BearingIndex
THE BEARINGINDEX DIRECTORY

22315 — 75 × 160 × 55 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22315

22315 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 75 × 160 × 55 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
75 unit unconfirmed
Outside D
160 unit unconfirmed
Width B
55 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

“It turned freely” is not a completed commissioning record.

For an assembled 22315 installation, ask which load and speed conditions will be used in the test run and who will accept the results. A demonstration without documented conditions cannot establish performance in the intended duty.

The factory row does not prescribe a commissioning load or speed sequence.

The exact Luan 22315 row/header [1] list d/D/B entries 75/160/55 without dimension units, grease/oil speeds 2000/2800 r/min, dynamic/static ratings 262/388 kN and reference mass 5.4 kg. Those are catalogue entries; they do not state the load to apply in a test run, an acceleration sequence or acceptance criteria.

Before starting the assembled machine, obtain the responsible maker/designer’s procedure for this actual bearing and arrangement. Identify the installed bearing, completed assembly checks, intended lubricant and proposed test conditions. Do not turn a catalogue speed entry into an instruction to accelerate directly to that speed.

Ask separately how the required bearing load will be established during the test. The dynamic and static ratings above are not a prescribed test force. If the proposed demonstration is described as “empty” or “no load,” have the responsible designer assess the actual bearing reactions and minimum-load requirement before accepting that plan.

SKF’s test-running guidance explicitly addresses load during startup.

SKF’s test-running guidance, printed 206 [2], calls for partial load and, with a wide speed range, low or moderate speeds. It warns against starting unloaded and rapidly accelerating to high speed because rolling elements may slide and damage raceways; minimum bearing load must be addressed.

This is general technical guidance, not a numeric startup instruction for Luan 22315. Give the supplier the actual machine configuration and proposed sequence. Request its written response on the load, speed changes and conditions appropriate to the supplied bearing.

Record which operating state a test actually covers. A short demonstration, a loaded commissioning sequence and an assessment of intended production duty are different evidence. If the supplier reports only that the shaft rotated, ask for the missing conditions and observations rather than interpreting that statement as full-duty acceptance.

A temperature or sound observation is a finding to assess, not a diagnosis by itself.

The same SKF page discusses an initial temperature rise and grease redistribution. It lists multiple possible contributors to unusually high temperatures, including lubrication, loading/distortion, associated parts and seals. That discussion does not diagnose any actual 22315 installation.

Ask for dated observations linked to the test stage, load, speed, lubricant and defined measurement point. If a result is unexplained, preserve the observation and have the responsible party assess it against the procedure. Do not label the machine “normal,” prescribe more lubricant or claim a damaged bearing from a lone temperature reading or sound description.

Commissioning recordInformation the buyer should request
Procedure and prerequisitesApproved sequence and criteria, actual bearing identity and arrangement, completed assembly checks and lubricant information.
Load and speed conditionsHow the actual bearing load is assessed, the agreed test stages and speed changes, and any unresolved minimum-load question.
ObservationsTime/stage, actual operating conditions, defined measurement locations, readings with units and recorded noise/vibration observations where required.
Acceptance and follow-upWho reviewed the findings, which criteria were met, what remains unexplained and whether further inspection or verification is required before release.

The exact Luan row/header and actual SKF test-running page were independently read and visually checked. No test has been performed here, no machine temperature, vibration or noise has been observed, and no Luan startup speed, test load, duration, threshold or fault cause has been selected. Request those decisions for the actual supply and machine.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22315
262388200028005.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22315.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22315

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22315.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22315 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22315 row and headers ↗

    Acquired 2026-10-09; exact row/header independently read/viewed:75/160/55 units unstated;2000/2800r/min;262/388kN;5.4kg. Test procedure unspecified.

  2. SKF · test running after assembly ↗

    Printed 206 independently read/rendered/viewed:load/startup guidance and observations. No Luan test conditions or diagnosis inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.