BearingIndex
THE BEARINGINDEX DIRECTORY

22315K — 75 × 160 × 55 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22315K

22315K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 75 × 160 × 55 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
75 unit unconfirmed
Outside D
160 unit unconfirmed
Width B
55 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Record where and in what state each clearance reading was taken.

A before-and-after pair of numbers needs an identified method and bearing state. For 22315K, ask the supplier to document the measurement positions and approved acceptance criterion, rather than reporting only that a feeler gauge was used.

The factory publishes ratings, not a measurement instruction for this supply.

The exact Luan 22315K row/header [1] list d/D/B entries 75/160/55 without dimension units, grease/oil speeds 2000/2800 r/min, dynamic/static ratings 262/388 kN and reference mass 5.4 kg. They do not state a clearance class, measurement position, mounting state or permitted change.

Ask for a maker-approved measurement and mounting instruction for the actual construction and support arrangement. Include a drawing or photograph showing access and the installed orientation. If a report supplies readings without identifying the physical bearing or method, ask for those details before using the numbers in an acceptance decision.

Keep the supplied class or catalogue range apart from actual measurements. A number taken from a table is not evidence that an identified delivered bearing was checked at that value.

SKF’s feeler-gauge explanation changes the measurement position with the mounting state.

SKF’s explanation, printed 205 [2], describes measuring between the outer ring and uppermost roller before mounting. During mounting, it describes the lowest roller and either ring according to the internal design. It also calls for ring rotation before measurement and centring of the rings and roller complement.

This explains why “feeler gauge used” is an incomplete record. Request a sketch identifying the measured gap and state for each reading. Have the responsible maker explain how the approved procedure handles the actual bearing construction and mounting access; do not substitute one convenient visible gap for the required measurement.

The SKF page separately discusses deformation effects and a multi-position method for larger bearings, particularly with thin-walled outer rings. It is not a universal correction to apply to every 22315K reading. No correction formula or gauge technique has been selected for the offered Luan bearing here.

A useful report makes the reading reproducible and its purpose clear.

Record fieldQuestion for the supplier or installer
Bearing and stageWhich identified bearing was measured, and was it unmounted, at an intermediate mounting stage or at the final mounted condition?
Position and supportWhich ring/roller gap was measured, in what orientation and support state? Does the record match the approved method for the actual construction?
Method and readingWhich procedure and measuring equipment were used, what value/unit was recorded and were any access or measurement limitations left unresolved?
Comparison and decisionWhat criterion applies to these readings, what change is being assessed and who accepted the result or requested further verification?

If a pair of readings appears inconsistent, first give the responsible maker the complete records and actual arrangement. Do not infer bearing damage, incorrect class or a successful fit from the numbers alone. Ask whether the measurements are comparable under the approved procedure and what further check is required.

The exact Luan row/header and actual SKF measurement text/figures were independently read and visually checked. No physical bearing has been measured, no Luan clearance class or allowable reduction has been assigned, and no installed fit or operating clearance has been approved. The supplier must resolve the missing dimension unit and method for the actual offer.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22315K
262388200028005.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22315K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22315K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22315K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22315K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22315K row and headers ↗

    Acquired 2026-10-09; exact row/header independently read/viewed:75/160/55 units unstated;2000/2800r/min;262/388kN;5.4kg. Measurement method and class unspecified.

  2. SKF · clearance measurements before and during mounting ↗

    Printed 205 text/figures independently read/rendered/viewed:measurement positions, centring and qualified larger-bearing discussion. No Luan measurement procedure or correction selected.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.