BearingIndex
THE BEARINGINDEX DIRECTORY

22316K — 80 × 170 × 58 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22316K

22316K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 80 × 170 × 58 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
80 unit unconfirmed
Outside D
170 unit unconfirmed
Width B
58 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The same bearing bore can belong to sleeve arrangements with different shaft diameters.

Before changing a sleeve type in a 22316K quotation, identify the complete assembly and actual shaft seat. A matching bearing bore is only one field; the proposed sleeve arrangement may require a different nominal shaft diameter.

The Luan row does not identify the shaft or sleeve assembly.

The exact Luan 22316K row/header [1] list d/D/B entries 80/170/58 with dimension units unstated, grease/oil speeds 1900/2600 r/min, dynamic/static ratings 288/405 kN and reference mass 6.4 kg. They do not specify a shaft seat diameter, sleeve type, assembly parts list or approved mounting arrangement.

Request the current bearing and proposed assembly drawing together with the actual shaft drawing. Mark the shaft seat separately from the bearing bore. If the supplier offers a different sleeve arrangement, ask it to identify every interface that changes before accepting the replacement.

A nominal diameter on a catalogue combination is not a machining tolerance or evidence of a measured installed shaft. Preserve the actual dimensions, tolerances and recorded measurements in the comparison rather than replacing them with a model-number assumption.

NSK’s two 22316 EAKE4 combinations share the bore, but not the shaft diameter.

NSK’s adapter table, printed C350, and withdrawal-sleeve table, printed C356 [2], separately list:

Exact NSK combinationSleeve-table typeShaft diameter d₁, mmNominal bearing bore d, mm
22316 EAKE4 + H2316XAdapter7080
22316 EAKE4 + AHX2316Withdrawal7580

Both rows explicitly identify an 80 mm nominal bore for this NSK bearing. Their shaft-diameter columns differ by 5 mm. That documented difference is enough to reject a comparison based only on the shared bore; it does not specify a shaft modification or approve either combination for Luan.

Keep the table type, complete bearing designation, exact sleeve code and shaft column together. Do not substitute H2316X for AHX2316 in an existing parts list merely because both reference 22316. Their different shaft fields need to be reconciled with the actual drawing and the responsible maker’s assembly proposal.

Make the supplier account for the shaft, axial location and service access.

Comparison to completeSupplier/designer response to request
Actual shaft versus proposed seatThe controlled shaft drawing and the proposed assembly’s required seat, units and tolerances; any difference explicitly identified and assessed.
Complete bearing and sleeve identityExact maker/designation, sleeve type and code, compatible components and approved parts list for the actual supply.
Axial location and lockingHow the bearing/sleeve is located in this arrangement, which existing shoulders or locking components are retained or changed and the approved drawing.
Mounting and later removalApplicable procedures, required access and tools, acceptance checks and unresolved constraints before the buyer commits to the proposal.

If a supplier cannot reconcile the shaft/interface drawing, keep the alternative as an unresolved proposal. Request clarification rather than describing it as a direct replacement or instructing the workshop to alter the shaft from these catalogue examples.

The exact Luan row/header and both NSK rows, table headings and diagrams were independently read and visually checked. No Luan sleeve compatibility, shaft diameter, tolerance, machining change, locking component or mounting result has been selected or verified. The dimension unit in the factory source still requires confirmation.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22316K
288405190026006.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22316K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22316K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22316K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22316K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22316K row and headers ↗

    Acquired 2026-10-09; exact row/header independently read/viewed:80/170/58 units unstated;1900/2600r/min;288/405kN;6.4kg. Shaft/sleeve arrangement unspecified.

  2. NSK · exact 22316 EAKE4 adapter and withdrawal examples ↗

    Printed C350 / PDF176:H2316X,shaft70/bore80mm. Printed C356 / PDF179:AHX2316,shaft75/bore80mm. Exact rows/headings/diagrams independently read/rendered/viewed; no Luan compatibility inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.