BearingIndex
THE BEARINGINDEX DIRECTORY

22317 — 85 × 180 × 60 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22317

22317 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 85 × 180 × 60 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
85 unit unconfirmed
Outside D
180 unit unconfirmed
Width B
60 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The 22317 number does not give every maker the same load rating.

A replacement quotation must identify the complete bearing and the rating set used in its assessment. The checked Luan, NSK and SKF entries below publish different ratings; a similar dimension pattern cannot justify borrowing another maker’s figures.

Three identified publications give three different rating sets.

The Luan 22317 row/header [1] give d/D/B entries 85/180/60 without dimension units, grease/oil speeds 1800/2400 r/min and reference mass 7.4 kg. Its dynamic/static ratings are 308/440 kN. The two separately checked catalogue examples have their own complete designations and explicit dimensional units:

Publication and complete designationPublished dimensionsDynamic / static basic ratings
Luan 22317 [1]85 / 180 / 60 — units unstated308 / 440 kN
NSK 22317EAE4 [2]85 / 180 / 60 mm600,000 / 630,000 N
SKF 22317 E [3]85 / 180 / 60 mm577 / 620 kN

NSK’s values convert to 600/630 kN; the conversion changes the unit, not the bearing to which the ratings belong. Neither catalogue resolves Luan’s missing dimension unit or approves interchangeability. Do not replace Luan’s 308/440 kN with a larger value found by searching the shared number.

If an offer quotes a different rating, ask for its complete designation, manufacturer document and revision. Record the offered construction and the basis for the difference before comparing proposals.

The catalogue needs bearing reactions; the machine’s total load is not enough.

NSK’s actual table and equations, printed C268–C269 [2], distinguish dynamic equivalent load P from static equivalent load P₀. Its dynamic formula is P = X Fᵣ + Y Fₐ, with a branch determined by Fₐ/Fᵣ relative to e. For its exact 22317EAE4 row, e is 0.33; the table lists Y₂ = 3.1, Y₃ = 2.1 and Y₀ = 2.0.

For the NSK table’s lower-ratio branch, X is 1 and Y is Y₃; above e, X is 0.67 and Y is Y₂. Its static equation separately uses P₀ = Fᵣ + Y₀ Fₐ. These are NSK’s definitions and coefficients for the stated design, not coefficients verified for Luan 22317.

For your enquiry, provide the radial and axial reactions at each bearing position, their directions and the operating cases. Ask the responsible designer how those reactions were obtained from the machine arrangement. A payload value without lever arms, support positions or the relevant bearing reactions leaves the calculation incomplete.

Do not label 308 kN or 440 kN as the machine’s permitted working load. Ask Luan for the applicable equivalent-load method and coefficients, then request an assessment against the actual rotating and static cases. Keep catalogue ratings, calculated equivalent loads and the final duty decision as separate fields.

Require a decision that can be traced back to this offered bearing.

  1. Identify the item. Attach the offered Luan drawing with dimension units, full construction and rating document. Compare the actual mounting interfaces and clearance requirements with the machine drawing.
  2. Identify the duty. Give normal and peak reactions, standstill or slow-motion loading where relevant, speed/time history and the intended lubrication. State required service and any missing inputs.
  3. Identify the calculation. Require the maker’s applicable coefficients, load cases, life/static assessment basis and assumptions for that exact supply. Ask which uncertainty still prevents approval.
  4. Record the outcome. Keep the responsible reviewer’s decision and conditions with the quotation. A larger published basic rating or matching dimension pattern alone is not an acceptance record.

The Luan row and both exact catalogue rows, headers and NSK equations were independently read and visually checked. No bearing reactions, service life, safety factor or permissible operating load have been calculated here. The comparison identifies questions for a documented replacement review; it is not a performance test or a replacement approval.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22317
308440180024007.42026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22317.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22317

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22317.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22317 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22317 row and headers ↗

    Acquired 2026-10-09; exact row/header read/viewed:85/180/60 units unstated;1800/2400r/min;308/440kN;7.4kg.

  2. NSK · 22317EAE4 exact row and equivalent-load equations ↗

    PDF135 / printedC268–C269 independently rendered/read/viewed:exact cylindrical22317EAE4 row;85/180/60mm;600000/630000N;e.33,Y2 3.1,Y3 2.1,Y0 2.0;dynamic branches and separate static equation. No Luan coefficients inferred.

  3. SKF · exact 22317 E catalogue row ↗

    PDF798 / printed796 independently rendered/read/viewed:22317E85/180/60mm;577/620kN. Full design and maker kept with ratings;no interchangeability approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.