BearingIndex
THE BEARINGINDEX DIRECTORY

22318 — 90 × 190 × 64 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22318

22318 is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 90 × 190 × 64 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
90 unit unconfirmed
Outside D
190 unit unconfirmed
Width B
64 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A seal material’s temperature range is only one part of a sealed-bearing proposal.

If a supplier proposes a sealed version for a 22318 position, obtain the complete designation and drawing. The checked SKF example is wider than its open counterpart, and its seal-material definition does not by itself approve the lubricant or the whole bearing at that temperature.

SKF’s actual 22318 open and sealed entries use different widths.

The Luan 22318 row/header [1] give d/D/B entries 90/190/64 without dimension units, grease/oil speeds 1700/2200 r/min, dynamic/static ratings 365/542 kN and reference mass 8.8 kg. The row does not specify a sealed construction or seal material.

SKF’s exact catalogue rows, printed 796 [2], list open 22318 E as 90 × 190 × 64 mm and sealed BS2-2318-2RS5/VT143 as 90 × 190 × 73 mm. The sealed example is 9 mm wider. Its full designation must stay with its drawing; “sealed 22318” leaves important construction information out.

Before reviewing temperature claims, compare the proposed width and interfaces against the actual assembly space. These SKF dimensions do not confirm Luan’s unstated units, prove that Luan supplies the same sealed design or approve either example as a replacement.

RS5 identifies a seal material; the rings and grease still need their own review.

SKF’s spherical-roller section, printed 776 [2], identifies RS5/CS5 seals as sheet-steel-reinforced HNBR. It separately identifies VT143 as the standard SKF LGEP 2 grease fill. These code meanings belong to SKF’s stated designs.

On printed 785 [2], SKF lists HNBR seal temperatures of −40 to +150 °C, but also says permissible bearing temperature can be limited by the rings, seals and lubricant. The same page’s ring heat-stabilization statement, at least 200 °C, is a separate material/design statement. It does not turn this sealed bearing and its grease into a 200 °C operating proposal.

For a quotation, ask the maker to assess the complete supplied construction at the actual temperature history. Specify where temperature was measured and how long peaks lasted. A housing reading without its location, method or relationship to the bearing/seal conditions leaves an important input unresolved.

Do not transfer the HNBR range or SKF’s ring treatment to an unspecified Luan seal, grease or bearing. Require the offered maker’s applicable limits and conditions for the actual supply.

Make the supplier’s temperature answer cover the complete item.

Proposal elementEvidence to request
Physical constructionFull designation and controlled drawing, actual seal arrangement, width and mounting interfaces; documented comparison with the machine space.
Rings and sealsApplicable ring condition and seal material for this supply, their temperature limits/conditions and the basis used for the stated duty.
Initial lubricantActual grease identity and applicable temperature/service assessment. A seal rating alone does not answer whether the initial grease suits the duty.
Operating decisionMaker’s assessment using actual temperatures, peak durations, load and speed; maintenance/replenishment conditions, responsible conclusion and remaining uncertainties.

If the offer says only “HNBR, suitable to 150 °C,” request the missing ring, lubricant and complete-duty basis. If it changes the grease or seal construction, keep the revised full designation and assessment with the quotation instead of assuming that the original example still applies.

The exact Luan row and SKF open/sealed 22318 rows, seal-code definitions and temperature-limit page were independently read and visually checked. No Luan sealed version, seal material, lubricant suitability, operating temperature or maintenance-free life is confirmed here. No thermal test or fit inspection has been performed.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22318
365542170022008.82026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22318.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22318

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22318.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22318 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22318 row and headers ↗

    Acquired2026-10-09;exact row/header read/viewed:90/190/64 units unstated;1700/2200r/min;365/542kN;8.8kg;seals/grease not identified.

  2. SKF · exact open/sealed 22318 entries, seal definitions and temperature limits ↗

    PDF798/printed796 exact22318E andBS2-2318-2RS5/VT143 widths64/73mm;PDF778/printed776 RS5HNBR andVT143LGEP2;PDF787/printed785 HNBR−40/+150°C and separate ring/seal/lubricant limits. Actual rows/pages/figures independently read/rendered/viewed. No complete Luan temperature approval inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.