BearingIndex
THE BEARINGINDEX DIRECTORY

22318K — 90 × 190 × 64 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

The source does not state dimension units. Obtain the offered drawing before using these historical values.

Spherical roller

22318K

22318K is a spherical roller designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 90 × 190 × 64 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Anhui province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
90 unit unconfirmed
Outside D
190 unit unconfirmed
Width B
64 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

An axial-load claim needs the shaft and sleeve arrangement as well as the bearing.

For a 22318K quotation on an adapter sleeve, ask where axial forces are reacted and whether the arrangement has a fixed abutment. The maker’s rating for the bearing alone does not document that mounting interface.

The Luan row does not describe the axial restraint of your assembly.

The Luan 22318K row/header [1] list d/D/B entries 90/190/64 without dimension units, grease/oil speeds 1700/2200 r/min, dynamic/static ratings 365/542 kN and reference mass 8.8 kg. They do not identify your sleeve, shaft shoulder or axial-retention capacity.

SKF’s actual sleeve arrangements, printed 787, figure 19 [2], distinguish adapter sleeves on plain and stepped shafts. The illustration is a general SKF arrangement, not a drawing of Luan 22318K. Ask the responsible designer to show the actual bearing, sleeve, locking components and any fixed abutment on the machine section.

Mark where axial force in each direction is reacted. Do not assume that “sleeve included” means the quoted package supplies every restraint needed by the assembly. Identify any missing distance, shoulder or retention component as an unresolved design item.

SKF gives a separate condition for an adapter sleeve without a fixed abutment.

On printed 784 [2], SKF first describes the spherical roller bearing’s ability to accommodate axial loading, then gives a specific formula for bearings correctly mounted on an adapter sleeve on plain shafts without fixed abutment: Fₐₚ = 0.003 B d. The symbols define B as bearing width in mm, d as bearing bore diameter in mm, and Fₐₚ as maximum permissible axial load in kN.

For its exact 22318 EK catalogue row on printed 796 [2], B is 64 mm and d is 90 mm. Substituting those SKF dimensions into that conditional formula gives 0.003 × 64 × 90 = 17.28 kN. This is an arithmetic illustration of SKF’s stated condition; it is not a measured capacity or a release of any installed assembly.

The formula does not use the bearing’s basic dynamic or static rating. It also does not use a sleeve’s shaft diameter in place of bearing bore d. A stepped-shaft arrangement with a fixed abutment is not the same stated condition. No result from this example is assigned to Luan: its units, actual construction, sleeve compatibility and mounting state remain to be confirmed.

Ask the quotation to cover both the bearing and its restraint.

Question to closeEvidence for the actual Luan proposal
Which arrangement is supplied?Controlled assembly section showing the exact sleeve/locking parts, shaft form and any fixed abutment; full bearing drawing with units.
Which forces must be restrained?Axial bearing reactions and direction for the relevant operating and exceptional cases, with the complete reaction path identified.
Which assessment applies?Maker’s retention basis for that assembly and mounting state, separately from the bearing load/life assessment. Keep its conditions and actual inputs with the result.
Who releases the proposal?Responsible review of the interface and bearing duty, required mounting evidence and remaining restrictions before acceptance.

If the supplier responds with only the 542 kN static rating, ask for the missing axial-retention basis. If it adds an abutment or changes the sleeve, require the revised drawing and review instead of carrying over an earlier assembly decision.

The exact Luan row, SKF 22318 EK row, conditional formula and sleeve figures were independently read and visually checked. No Luan sleeve, fixed-abutment design, retention limit or operating load is approved here. The worked number is explicitly SKF-specific and conditional; it is not a capacity test.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Limiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
Luan Rolling Bearing
22318K
365542170022008.82026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 22318K.

Luan Rolling Bearing

Luan, Anhui, China

Spherical and cylindrical roller bearings

Lu’an Rolling Bearing publishes LZ spherical and cylindrical roller bearings, non-standard bearings and rolling elements. Its multi-model tables must be read by the exact row designation. Request the offered drawing, confirmed dimension units and complete construction before approving a replacement.

Published ranges: Spherical roller bearings · Cylindrical roller bearings · Nonstandard bearings · Spherical and cylindrical rollers

168 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Luan Rolling Bearing about 22318K

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 22318K.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Luan Rolling Bearing · 22318K source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Luan Rolling Bearing · exact 22318K row and headers ↗

    Acquired2026-10-09;exact row/header read/viewed:90/190/64 units unstated;1700/2200r/min;365/542kN;8.8kg.No actual sleeve/retention rating.

  2. SKF · conditional axial loading, sleeve arrangements and exact 22318 EK dimensions ↗

    PDF786/printed784 Fap=.003Bd for correctly mounted adapter sleeve/plain shaft/no fixed abutment, explicit symbols/units;PDF789/printed787 fig19 plain/steppedshaft;PDF798/printed796 exact22318EK90/190/64mm. Actual pages/rows/figures read/rendered/viewed;17.28kN is conditional SKF arithmetic,not Luan or tested assembly capacity.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.