BearingIndex
THE BEARINGINDEX DIRECTORY

234406-M — 30 × 55 × 32 mm

BOUNDARY DIMENSIONSUNIT / mm

YJB’s 234406-M detail places this part in its double-direction thrust angular contact range and gives d30, D55 and B32 mm. The same entry also gives C16 and B1 8 mm. These are different dimension arrows in the manufacturer’s section sketch; a generic radial-bearing drawing does not describe this assembly.

Thrust

234406-M

234406-M is a thrust designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 30 × 55 × 32 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
30 mm
Outside D
55 mm
Width B
32 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 55 × 32 seat and a “Cr” number do not identify the 234406-M offer.

YJB’s 234406-M has a 30 mm bore; its nearby 234706-M has a 32 mm bore despite the same 55 mm outside diameter and 32 mm width. The 234406-M entry also uses “Cr” twice, with different numbers and incomplete explanations. Resolve those fields with YJB before using a quotation to specify load or rigidity.

Ask what 15300 and 276 measure before comparing them.

YJB’s exact 234406-M detail [1] separates a basic-load group from three final fields. Keep the original Chinese labels in your technical question: translating both occurrences of Cr into “load rating” would already make an unsupported decision.

YJB source positionAs publishedWhat the quotation must clarify
Basic-load group动载荷 Cr KN: 15300Confirm the load direction, intended unit and corrected specification. Do not silently reinterpret KN as N or divide the number to create a rating.
Basic-load group静载荷 Cor KN: 36000Confirm its definition and unit separately from the dynamic field.
Final fields after speedFv: 108 · KaE: 308 · Cr: 276Supply definitions, units and the configuration to which each value applies; these are not explained in the examined entry.

The model-specific downloaded PDF [2] repeats these labels and values. It is another presentation of the manufacturer’s record, rather than an independent test or a resolution of the missing definitions. Preserve both source locations when asking for a corrected specification.

Why a FAG catalogue does not settle YJB’s fields: Schaeffler SP 1, pages 161–163 [4], identifies a separate 234406-M-SP. Its axial ratings are Ca15700 N and C0a38500 N. Its final columns explicitly identify FV108 N as preload, KaE308 N as lift-off force and ca276 N/µm as axial rigidity. Those definitions and ratings belong to the FAG entry. Matching final numbers do not establish what YJB’s unqualified Cr276 means.

For a load calculation, obtain YJB’s confirmed axial-rating definition and unit. For an axial-displacement calculation, obtain YJB’s confirmed rigidity definition and its preload/configuration basis. Neither task can use “276” solely because another brand prints it with a rigidity unit. Keep FAG’s complete -M-SP designation in any separate comparison; the shared 234406 number does not certify YJB’s accuracy, cage or interchangeability.

The directory retains its historical 11000/16000 rpm fields with source notes. YJB’s current speed group prints “极限转速 min” and separate grease/oil labels, without an explicit reciprocal-minute unit. Ask for the intended unit and lubrication conditions together with the corrected load fields. Selecting the larger oil-labelled number does not establish the offered assembly’s suitability for that operating speed.

Separate the 30 mm bore from the shared 55 × 32 dimensions.

The nearest misleading match is in YJB’s own 234706-M detail [3]. Both entries are under its double-direction thrust angular contact range and share D and B, but the bore changes. Use the complete model and all three dimensions when identifying the old part.

YJB dimension, mm234406-M [1]234706-M [3]
Bore d3032
Outside diameter D5555
Width B3232
Dimension C1616
Dimension B188
Dimension d14747

A quotation identifying only 55 mm OD and 32 mm width leaves these two entries unresolved. The 2 mm bore difference is a difference between published entries, not an available fit allowance. Do not approve the 32 mm-bore proposal for a 30 mm interface from the matching OD and width.

Open the section sketch linked by YJB’s detail alongside your old assembly drawing. It marks B across the assembly, with separate C and B1 arrows; d and d1 are also separate arrows. The installation sketch then uses da and Da. YJB’s 234406-M entry lists da h12 as 40.5 and Da H12 as 50.5 in its installation group, rather than as the bore30 or outside diameter55.

Ask YJB to mark those exact arrows on the offered, revision-controlled drawing and identify their units and tolerance scope. Do not substitute da40.5 for the 30 mm bore, or Da50.5 for D55; do not treat B32, C16 and B1 8 as interchangeable axial-stack measurements. The linked sketch explains where symbols are placed but supplies no approval of your shoulder geometry, clamping or installed preload.

Send the existing axial locating surfaces and the full bearing-set identification with the drawing. Have YJB state which components and configuration its quote includes. The examined webpage and its generated PDF do not establish an installation torque, a preload-setting procedure or the acceptability of mixing components from a FAG -M-SP set.

What each manufacturer published.

ManufacturerLimiting speed — grease (rpm)Limiting speed — oil (rpm)Reference mass (kg)Source recorded
YJB
234406-M
11000
Historical directory entry: 11000 rpm. Current YJB detail says nG脂 11000 under “极限转速 min”; it does not print min⁻¹. Confirm the intended speed unit and offered lubrication conditions.
16000
Historical directory entry: 16000 rpm. Current YJB detail says nG油 16000 under “极限转速 min”; confirm the intended unit and oil arrangement rather than approving duty from this number.
0.292026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish 234406-M.

YJB

Hangzhou, Zhejiang, China

Precision spindle and machine-tool bearings

YJB publishes precision angular-contact, double-row cylindrical roller and ball-screw bearing ranges. Its NN3006-K-W33 catalogue separates bearing dimensions from mounting callouts. Confirm the offered bore, precision and lubrication configuration against the actual spindle drawing.

Published ranges: Angular contact ball bearings · Cylindrical roller bearings · Double-direction thrust angular contact bearings · Tapered roller and nonstandard designs

740 designations documented here · 1 reviewed evidence record · source recorded 2026-10-07

Ask YJB about 234406-M

Applications the publishing works state.

ApplicationStated by
Instrument motorsYJB
Machine-tool spindlesYJB
Medical equipmentYJB
RoboticsYJB

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for 234406-M.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YJB · 234406-M source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YJB · exact 234406-M detail ↗

    30/55/32 mm and separate C/B1/d1 arrows, source-linked section sketch; original KN15300/36000 labels, final Fv/KaE/Cr and minimum-speed headings that the page does not define. These ambiguities remain unresolved.

  2. YJB · generated 234406-M PDF ↗

    Two-page model PDF repeats the website fields. No independently corrected unit explanation or installed-assembly test is established.

  3. YJB · exact 234706-M detail ↗

    32 mm bore versus 234406-M30 mm, with shared D55/B32/C16/B1 8/d1 47 mm. Used only to expose incomplete identification, not to recommend a replacement.

  4. Schaeffler · Super precision bearings SP 1 ↗

    Pages161–163: separate FAG234406-M-SP row and symbol/unit explanations. Its explicitly defined ratings and final fields do not confirm or correct YJB’s values or configuration.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.