PLB 30205: bore d 25 mm, outside diameter D 52 mm, assembled width T 16.25 mm, inner-ring width B 15 mm and outer-ring width C 13 mm. T, B and C span different surfaces in PLB’s linked section sketch. Use T for the complete assembly’s axial width; B is not a substitute for T.
Tapered roller
30205
30205 is a tapered roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 25 × 52 × 16.25 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Identify the whole 30205 assembly, then keep the ring widths and suffixes visible.
PLB’s exact 30205 table gives three different axial dimensions: T 16.25, B 15 and C 13 mm. The complete assembly does not have a 15 mm total width. A second identification trap is NSK’s HR30205C: it shares d 25/D 52/T 16.25/B 15 mm with the comparison entries, yet specifies a 12 mm outer-ring width. The complete designation and the surfaces behind each dimension belong on the quotation.
The total width is 16.25 mm. The 15 mm field belongs to the inner ring.
Identify both nominal radial interfaces alongside the axial dimensions.
T
16.25 mm
Complete assembled width in PLB’s section sketch.
B
15 mm
Inner-ring width. Do not use it as the complete assembly thickness.
C
13 mm
Outer-ring width. This source-backed field is additional to the older directory’s stored dimensions.
If an enquiry says “30205, 25×52×15”, ask which surfaces define its last number. The 15 mm value can identify B, but it leaves T unresolved. PLB’s complete dimensional description here is d 25/D 52/T 16.25 mm, with separate B 15/C 13 mm ring widths. Keep the symbols on the drawing instead of reducing these five measurements to an unlabeled three-number size.
T minus B is 1.25 mm for this published entry. That arithmetic compares two different drawing dimensions; it is not an installed clearance, a spacer thickness or a preload adjustment. The source sketch has no controlled tolerance or setting procedure that would turn this difference into an installation instruction.
The detail also writes R 1.0 and r 1.0 without an explicit unit beside those fields. The small section sketch identifies separate corner arrows, but does not establish permissible mating fillets or a machining tolerance. Ask PLB to mark the offered interfaces and tolerances on a revision-controlled drawing, keeping the existing shaft and housing locating surfaces with the enquiry.
The downloadable model PDF repeats the same 30205 values. It is a manufacturer-generated presentation of this entry, rather than an independent measurement report. The directory keeps its historic d/D/T/B and 0.15 kg record and original recording date; the newly checked C 13 mm belongs to the cited current source.
Matching d, D, T and B still leaves a different outer ring.
The following comparison uses two NSK HR30205J [4] and HR30205C [5] entries as separately named designs. It does not relabel either as PLB 30205 or recommend either as a replacement.
Complete source designation
Bore / OD / total width / inner-ring width, mm
Outer-ring width C, mm
PLB 30205 [1]
25 / 52 / 16.25 / 15
13
NSK HR30205J [4]
25 / 52 / 16.25 / 15
13
NSK HR30205C [5]
25 / 52 / 16.25 / 15
12
NSK identifies its C configuration with a contact angle of about 20° and explains the C suffix as a medium-angle design requiring consultation for its application. The dimension symbol C in the table means outer-ring width; the C in HR30205C is part of NSK’s full designation. Keep both meanings separate.
Two offers can share the main envelope and still differ. The C-suffix entry’s 12 mm outer-ring width differs from the 13 mm entries. This difference is a source comparison, rather than a measured fit allowance or evidence that any ring can be moved to another assembly. Provide the actual old markings and cup/cone identity when asking a supplier to assess a change.
The matching five nominal dimensions of the PLB and NSK J entries establish only the geometry listed above. They do not establish equal internal design, contact angle, accuracy, component interchange or installed setting. PLB’s examined detail provides no model-specific load or speed ratings to compare with NSK’s entries. Leave PLB’s fields unprovided and ask PLB for its own 30205 specification; do not populate them from the better-documented NSK design.
For a comparable quotation, request the complete PLB 30205 assembly and its component identification, attach the T/B/C drawing arrows, and have the supplier identify every proposed suffix or brand change. If the old assembly is marked HR30205C, retain that complete marking in the request so the 12 mm outer-ring entry and its application-specific design are assessed explicitly.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.
PLB connects a searchable miniature/automotive catalogue with named inspection equipment and ring/assembly process steps. Specify closure-dependent widths, keep alternator reference numbers separate from the delivered construction, and request part-linked test conditions for custom robot or rail-component work.
Published ranges: Automotive alternator and steering bearings · Motor bearings · Precision spindle-bearing applications · Nonstandard bearing designs
124 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Current exact d 25/D 52/T 16.25/B 15/C 13 mm, 0.150 kg and source-linked section sketch actually examined. R/r fields omit explicit units; no controlled tolerances or PLB 30205-specific load/speed figures established.
Two-page manufacturer-generated model PDF repeats the dimensional values. It belongs to the same publication as the website, rather than an independent test or resolution of drawing tolerances.
Exact 25/52/16.25/15/13 mm dimension definitions. Used for the named comparison; its separate performance, abutment and setting data are not PLB specifications.
Exact 25/52/16.25/15/12 mm and about 20° contact-angle property; C suffix requires its own application assessment. Shared dimensions do not erase the suffix or approve replacing a PLB assembly.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies