Runstar identifies the shaft-washer bore as 25 mm and housing-washer bore as 26 mm for 51105. PLB’s series drawing uses d1/D1 on different diameter features from Runstar’s text table. Use each supplier’s own drawing and labels; 25×42×11 mm alone does not identify every washer or mounting interface.
Thrust
51105
51105 is a thrust designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 25 × 42 × 11 mm. The publishing works are in Zhejiang, Fujian provinces, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Identify the two washers and the supplier’s drawing before approving a 51105 replacement.
Runstar and PLB both publish 51105 at 25×42×11 mm. Runstar additionally lists a 26 mm housing-washer bore and separate grease/oil speeds of 4300/6000 rpm. PLB publishes its own size and mass row with a series mounting diagram whose diameter symbols differ from Runstar’s detail. Keep those two evidence sets separate when checking the washers, mating shoulders and intended lubrication.
Runstar’s d1 is a 26 mm bore; PLB’s drawing puts d1 on an outside diameter.
Runstar’s 51105 detail [1] identifies the two washers separately. Keep the supplier’s component names with its numbers when checking an existing 25 mm shaft assembly. Ordering from the three-number size without the washer drawing leaves the second bore and seating interfaces unresolved.
Runstar detail label
Published 51105 value
Interface to check
Shaft-washer bore d
25 mm
Identify this washer and its shaft fit on the selected drawing.
Housing-washer bore d1
26 mm
This is not another 25 mm bore. Keep its component identity during assembly and replacement.
Housing-washer outside D / shaft-washer outside D1
42 / 42 mm
The equal outside sizes do not identify which washer belongs to each mating seat.
Assembled thickness H
11 mm
Check the complete stack and mating datums; the directory’s historical size field is called B.
PLB’s series section [3] labels total thickness H, an outside feature d1 and an inside feature D1. Runstar’s text table uses d1 for the housing-washer bore and D1 for the shaft-washer outside diameter. Consequently, copying “d1 = 26” from Runstar into PLB’s d1 field would assign the number to a different feature. Match the geometry and component names first, then use the offered supplier’s numerical drawing.
PLB’s exact 51105 publication [2] gives d25/D42/B11 mm and 0.056 kg; it does not give selected numerical values for the series diagram’s other interfaces. Its right-hand mounting sketch labels shoulder references da/Da and corner ra. Obtain these for PLB’s offered 51105, rather than fill them from Runstar’s row or from a different brand.
Runstar lists a 0.6 mm chamfer without a complete selected drawing defining each corner and the mating shoulder limit. That entry alone does not establish the permissible housing or shaft fillet. Request washer seating faces, allowable corner clearance, fits and axial retention together. If the application reverses its axial force or also needs radial support, provide the whole arrangement for review; PLB calls this family single-direction thrust, and Runstar describes axial loading. Neither exact row approves the machine’s complete support arrangement.
At 5000 rpm, Runstar’s grease and oil entries lead to different checks.
51105 publisher
Published mass and loads
Published speed information
Runstar [1]
55 g; Cr 15.2 / Cor 30.2 kN.
Grease 4300 rpm; oil 6000 rpm.
PLB [2]
0.056 kg, equivalent to 56 g. This exact row provides no load entries.
No selected speed entry in the exact row examined; ask PLB for its own assessed conditions.
For a 5000 rpm requirement, Runstar’s published grease entry is lower than the requested speed. The oil entry is higher, but that does not approve simply changing lubricant: ask Runstar to assess the oil supply, installed load, temperature and support arrangement for the offered configuration. A PLB quotation requires PLB’s own speed evidence; Runstar’s 6000 rpm figure cannot fill PLB’s missing entry.
The 1 g difference between the published masses is not a verified quality ranking or proof of a construction difference. Both catalogues show the same nominal three-number size, while selected fits, component details and operating conditions still require confirmation. Likewise, the larger static load number is not a general permissible machine load; obtain the applicable load definitions and assembly assessment.
Runstar lists bearing-steel 52100 (GCr15) washers and balls, with a copper or steel cage. Have the quotation select the actual cage and lubricant so that the delivered configuration is identifiable. The page’s −30 to 130°C range and speed entries are separate catalogue statements, without a combined installed-duty test here. Do not treat 6000 rpm at 130°C as a demonstrated operating point.
Runstar also displays ABEC-1 with higher grades offered, C0 with other groups offered, and “PASSED” entries for ISO9001:2015, REACH and ROHS. These page entries are supplier claims or options; they do not select an upgraded grade or provide the certificate/report for the particular shipment. Ask for the specified dimensional and running-accuracy records, offered material documentation and any required certificate scope, then retain them with the selected assembly drawing and order.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.
Compare the recorded figures.
Property
Finding
Sources
Bore
All 2 sources publish 25 mm
2
Outside diameter
All 2 sources publish 42 mm
2
Width
All 2 sources publish 11 mm
2
Reference mass
Ranges 0.055 – 0.056 kg across 2 sources
2
Where the figures differ, use the drawing from the manufacturer you buy from.
PLB connects a searchable miniature/automotive catalogue with named inspection equipment and ring/assembly process steps. Specify closure-dependent widths, keep alternator reference numbers separate from the delivered construction, and request part-linked test conditions for custom robot or rail-component work.
Published ranges: Automotive alternator and steering bearings · Motor bearings · Precision spindle-bearing applications · Nonstandard bearing designs
124 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.
Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs
223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Explicit washer dimensions: shaft bore25 mm, housing bore26 mm, both outside diameters42 mm, H11 mm and chamfer0.6 mm. Mass55 g, Cr15.2/Cor30.2 kN, grease4300/oil6000 rpm and offered cage/material entries. Site claims and options are not shipment records or combined-duty testing.
d25/D42/B11 under dimensions(mm), mass0.056 kg. The examined exact publication does not supply selected load/speed figures or numbers for the additional series drawing references.
Series H, d/D and d1/D1 geometry plus shoulder da/Da and corner ra references. PLB’s d1/D1 point to different diameter features from Runstar’s exact text labels; use the offered supplier’s controlled drawing.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies