BearingIndex
THE BEARINGINDEX DIRECTORY

FR1-5 2RSEE — 2.3812 × 7.9375 × 3.5712 mm

RECORDED BODY DIMENSIONSUNIT / mm

The 2.3812 × 7.9375 × 3.5712 mm historical record describes bore, body diameter and outer-ring width. The sealed drawing also has a wider inner ring and a 9.1186 mm flange. Use those separate interfaces when checking the assembly.

Ball bearings

FR1-5 2RSEE

FR1-5 2RSEE is a ball bearings designation documented on BearingIndex from 1 manufacturer publication. Runstar’s sealed form has outer-ring width C 3.571 mm and inner-ring width B 4.366 mm. Compared with its FR1-5 EE open form, both ring widths and the flange thickness increase; the replacement guide below follows those interfaces. The publishing works are in Fujian province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
2.3812 mm
Outside D
7.9375 mm
Outer-ring width C
3.5712 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Changing FR1-5 EE from open to sealed changes the axial stack, even though the bore and body diameter stay the same.

Runstar’s FR1-5 EE open form and FR1-5-2RS EE sealed form share their published bore, body diameter and flange diameter. Their axial dimensions differ: the sealed form has a wider outer ring, wider inner ring and thicker flange. For an existing small mechanism, review the flange seat, the inner-ring spacer and the cover separately before accepting the sealed replacement. A suffix change alone is not a complete replacement specification.

Three axial dimensions change in an OPEN-to-2RS replacement.

The exact FR1-5-2RS EE sealed page [1] and FR1-5 EE open page [2] give bore 2.381 mm, body diameter 7.938 mm and flange diameter 9.1186 mm. These common dimensions explain why a sealed replacement may look plausible when compared only by the shaft and housing bore. The same pages show three different axial dimensions:

Axial interfaceFR1-5 EE openFR1-5-2RS EE sealedChange, calculated from published mm values
Outer-ring width C2.779 mm3.571 mm+0.792 mm
Inner-ring width B3.571 mm4.366 mm+0.795 mm
Flange thickness Bf0.5842 mm0.7874 mm+0.2032 mm

These are changes to three different spans, not instructions to add one shim. The table does not tell you how each ring face moves relative to the installed flange seating face. In particular, the 0.795 mm increase in inner-ring width is not a verified change in either individual end-face position.

Follow the stationary parts first.

On the existing assembly section, identify the surface that seats the flange and any shoulder or cover that locates the outer ring. Carry those references to the sealed bearing drawing. The thicker flange and wider outer ring must be checked against that arrangement together. Do not move a housing stop by the width difference alone: first establish which bearing face the stop contacts and where that face lies from the seating datum.

The flange also needs its own radial space. Its 9.1186 mm outside diameter is larger than the 7.938 mm body, so the body-bore number does not describe the flange seat or cover opening. Retaining the same body diameter does not settle either clearance.

Then follow the shaft, spacer and inner ring.

The sealed inner ring is 4.366 mm wide. The old open bearing’s inner ring is 3.571 mm wide. Identify the spacer and shaft shoulder that locate that ring, then check both ring-face positions using the selected drawing. A spacer chosen from the sealed page’s header “B 3.571” would use the outer-ring width instead of the detailed inner-ring width.

Finally check the stationary cover against the moving assembly at its actual installed positions. Changing the spacer to make one end line up does not by itself establish clearance at the other end. The source drawing depicts the wider inner ring, but does not dimension its individual projections from the flange seating datum.

What to return for drawing approval.

Send one section showing the flange seat, the outer-ring stop, the shaft shoulder, the spacer and the cover. Mark which ring each locating part contacts and the clearances that the mechanism requires. Ask for the sealed bearing’s ring-face coordinates from the chosen flange seating datum and the applicable limits. The existing dimensions plus that returned datum information allow a stack review; the three nominal increases above cannot release mating-part machining on their own.

Runstar’s part-numbered sealed section [3] uses B1 for the inner-ring span, C1 for the outer-ring span and Cf1 for flange thickness; its table uses B, C and Bf. Match the physical span when moving between the table and drawing. For the sealed part, 4.366 − 3.571 = 0.795 mm is the total nominal ring-width difference. It must not be divided into two assumed 0.3975 mm projections.

A ZZ EE replacement starts with different geometry evidence.

If the existing part is FR1-5ZZ EE [4], Runstar lists the same outer width 3.571 mm, inner width 4.366 mm and flange thickness 0.7874 mm as the sealed form. The OPEN-to-2RS increases above therefore do not apply to that starting part. Keep its complete designation with the assembly review instead of treating every FR1-5 EE variant as the same old bearing.

The ZZ page identifies shields; the 2RS page identifies rubber seals. Matching nominal ring and flange dimensions gives a useful geometric starting point, but no published numerical seal-drag or limit-speed comparison establishes the same running behaviour. If the purpose of changing the closure is protection from a specific exposure, state that exposure in the order and agree the selected seal construction and running requirement. This page does not assign a rubber compound, ingress rating or speed value that the selected product source does not provide.

Keep the replacement decision tied to the old form: OPEN requires review of the changed ring widths and flange thickness; ZZ has matching published nominal spans but a different closure. In both cases, retain the wide-inner-ring EE designation and the approved face locations. The old directory’s single width field is insufficient to specify that assembly.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Outer-ring width C (mm)Reference mass (kg)Source recorded
Runstar
FR1-5 2RSEE
2.38127.93753.5712
Stored in the old B field: 3.5712 mm. The detailed source identifies this as outer-ring C, displayed as 3.571 mm; inner-ring B is 4.366 mm.
0.00115
Historical header value: 1.15 g (0.00115 kg). The same page’s technical table gives 0.67 g; use neither as an agreed receiving tolerance.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish FR1-5 2RSEE.

Runstar

Zhangzhou, Fujian, China

Miniature ball and thrust bearings

Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.

Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs

223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Runstar about FR1-5 2RSEE

Applications the publishing works state.

ApplicationStated by
Fishing tackleRunstar
Medical equipmentRunstar
Precision instrumentsRunstar
Small motorsRunstar

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for FR1-5 2RSEE.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Runstar · FR1-5 2RSEE source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Runstar · FR1-5-2RS EE sealed detail ↗

    Detailed table: rubber seals; d 2.381 mm, D 7.938 mm, Df 9.1186 mm, outer C 3.571 mm, inner B 4.366 mm and flange Bf 0.7874 mm. Header B refers to the narrower outer span. Header/table mass values differ.

  2. Runstar · FR1-5 EE open detail ↗

    Open form with the same listed bore, body and flange diameters; outer C 2.779 mm, inner B 3.571 mm and flange Bf 0.5842 mm. Used as the defined starting part for the axial comparison.

  3. Runstar · FR1-5-2RS EE section drawing ↗

    Part-numbered section depicts separate inner/outer widths and flange. B1/C1/Cf1 differ from the table notation; individual ring-face offsets and tolerances are not specified.

  4. Runstar · FR1-5ZZ EE shielded detail ↗

    Shields; listed outer/inner widths 3.571/4.366 mm and flange thickness 0.7874 mm match the sealed nominal spans. No supplied seal-drag or speed equivalence is inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.