BearingIndex
THE BEARINGINDEX DIRECTORY

GE12ES — 12 × 22 × 10 mm

BOUNDARY DIMENSIONSUNIT / mm

Wuling’s GE12ES image gives d 12 / D 22 / B 10 / C 7 / d1 min 15 mm and an 11° angle entry. B and C are different ring widths; the angle is drawn between the shaft axis and housing axis. A generic d/D/B sketch does not describe the full articulating interface.

Spherical plain

GE12ES

GE12ES is a spherical plain designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 12 × 22 × 10 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
12 mm
Outside D
22 mm
Width B
10 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Read the GE12ES row before choosing a seal or approving the joint’s motion.

Wuling’s original image confirms 12/22/10 mm for GE12ES and adds outer-ring width 7 mm, d1 min 15 mm and an 11° angle entry. Its series heading shows ES and ES-2RS, but the exact 12ES row lists no 2RS partner. The same row’s dynamic 10.8 and static 54 fields have no stated unit. These details answer different procurement questions; none should be decided from the three-number size alone.

The series heading supplies two constructions; the 12ES row supplies one designation.

Wuling’s original parameter image [1], linked by its GE.ES product page [2], shows two section sketches and the headings GE...ES and GE...ES-2RS. Read the exact row before transferring that family presentation into an order.

Location in the same imageDesignations actually printedWhat the quote must resolve
12 mm bore rowGE12ES; its second designation space is blank.If sealing is required, ask Wuling for the exact offered construction and drawing. This row does not document GE12ES-2RS.
15 mm bore rowGE15ES and GE15ES-2RS.This shows that the image can name a 2RS partner explicitly. It is not a sealed 12 mm alternative.

A blank second space means this examined table does not list that designation. It does not prove that Wuling cannot make any sealed 12 mm joint. Ask for a current model-specific response if the supplier proposes GE12ES-2RS; keep that response and its drawing distinct from the source record for GE12ES.

The adjacent sketches illustrate the series’ different constructions. They are not a photographed GE12ES lot or confirmation of this offer’s seal material and lubrication holes. Likewise, a seal request does not decide whether the actual sliding pair needs maintenance. Get the selected construction’s sliding-surface materials, seal arrangement and lubrication path on the quotation.

Keep another brand’s suffix rules separate. Schaeffler’s HG1 catalogue [3] identifies its separate GE12-DO with a footnote stating no relubrication facility. A matching nominal size cannot transfer that construction to Wuling’s GE12ES, or confirm that the Wuling part has a replenishment hole. Ask about the actual offered part.

11° is the image’s tilt entry, not the joint’s full swivel travel.

In the Wuling drawing [1], the angle arrow is at the shaft axis relative to the housing axis. The exact GE12ES row reads a°11. Keep that motion separate from back-and-forth rotation about the bore axis.

GE12ES image fieldPublished entryKeep this interface on the drawing
d / D12 / 22 mmNominal shaft bore and outside diameter.
B / C10 / 7 mmSeparate ring widths; B 10 does not give the width of the outer ring.
d1 min15 mmRetain d1 and its minimum qualifier on the offered drawing; do not relabel it as bore d 12.
a°11°Axis tilt shown in the section, with the offered tolerance and actual adjacent-part clearance to be checked.

Schaeffler HG1, printed page 45 [3], distinguishes swivel motion about the bearing axis between two reversal points from tilt between the ring axes. That terminology helps describe the requirement; it does not supply Wuling’s permitted swivel travel, frequency or operating life.

For example, a requirement for 12° of axis tilt already exceeds Wuling’s listed 11° entry. Ask Wuling for another controlled configuration or an explicit engineering assessment rather than approving the row from its 12 mm bore. A requirement for 12° of swivel travel is a different question: the 11° tilt entry alone neither approves nor rejects it.

Attach the actual shaft shoulder, locating washers, housing retention and required positions of the articulated assembly. Have Wuling identify B/C/d1 on its offered drawing and show clearance throughout the requested tilt. The 11° catalogue entry is not a measured guarantee that your surrounding hardware can reach 11°, and it supplies no permission to grind a washer or enlarge a housing to obtain more movement.

C 7 mm and dynamic C 10.8 belong to different groups.

The exact row contains two uses of C: C 7 under Dimensions(mm) is an outer-ring width, while dynamic C 10.8 under Load ratings is a load-field number. The static field reads Co 54. The image gives no unit for the two load columns.

As published for GE12ES [1]Confirmed scopeUnresolved issue
C 7Outer-ring width 7 mm.It is not dynamic load C.
Dynamic C 10.8 / static Co 54Two source numbers under their dynamic/static labels.Unit, load-direction definition and applicable construction/conditions.
Weight 0.0160.016 kg in the original image.Catalogue mass, rather than a measured delivered part or a load-capability test.

Do not append kN from convention or from Schaeffler’s separate data. Do not treat 54 as an allowable installed load just because it is the larger number. Ask Wuling to return its GE12ES rating definitions and units, identify the selected sliding pair and explain how the required loads and motion are assessed.

Send the actual load history with radial/axial directions, the separately defined tilt and swivel motion, and the reversal frequency. A bare “12×22×10, 54 load” request leaves both the interface and load meaning unresolved. A useful response ties the exact GE12ES construction to the controlled drawing and a permissible-duty assessment; until then the image’s load numbers remain source-labelled numbers rather than a sizing result.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Inner-ring width B (mm)Source recorded
Wuling
GE12ES
1222102026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish GE12ES.

Wuling

Lishui, Zhejiang, China

Linear and spherical plain bearing systems

Wuling publishes linear-motion parts and articulating joints. Its radial spherical-plain catalogue separates ring widths and lists seal variants by exact row; specify the joint’s required movement and the complete offered construction.

Published ranges: Linear ball bearings · Stud-type needle track rollers · Rod-end and spherical plain bearings · Linear guides and sliding units

52 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Wuling about GE12ES

Applications the publishing works state.

ApplicationStated by
Machine toolsWuling
Medical machineryWuling
Printing machineryWuling
Textile machineryWuling

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for GE12ES.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Wuling · GE12ES source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Wuling · original GE.ES parameter image ↗

    Exact GE12ES row and all headings actually read: dimension group mm; 12/22/10/7/d1 min 15, angle 11°, weight 0.016 kg. Load 10.8/54 has no unit, and the 12ES row has no second sealed designation. Family sketches do not establish the delivered configuration.

  2. Wuling · GE.ES product publication ↗

    Official single-split radial spherical plain-bearing page links the original image and identifies the supplier. It provides no separate GE12ES load-unit clarification, controlled angle tolerance or configuration-specific duty approval.

  3. Schaeffler · HG1 plain-bearing catalogue ↗

    2016 catalogue, printed pages 45/188 actually read: swivel/tilt distinction and separate GE12-DO relubrication footnote. Used as named background, rather than Wuling construction, maintenance, rating or interchange approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.