BearingIndex
THE BEARINGINDEX DIRECTORY

GE20ES — 20 × 35 × 16 mm

INNER AND OUTER RING WIDTHS DIFFERUNIT / mm

Both original sections distinguish inner-ring B 16 mm from outer-ring C 12 mm. The 20 × 35 × 16 mm record is not the outer-ring housing-seat width. Check the joint’s tilt and oscillating travel separately.

Spherical plain

GE20ES

GE20ES is a spherical plain designation documented on BearingIndex from 2 manufacturer publications. The two manufacturers list GE20ES at d 20/D 35/inner-ring B 16 mm, with outer-ring C 12 mm. Jingjiu lists 30/146 kN dynamic/static ratings and an approximate 9° inclination. Its rating numbers alone do not establish operating life. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
20 mm
Outside D
35 mm
Inner-ring width B
16 mm

Compare the 2 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A GE20ES quote needs a life requirement as well as a load rating.

Jingjiu publishes GE20ES with a 30 kN dynamic rating. SKF’s actual sizing example shows why that number alone cannot settle the life requirement. Keep the offered manufacturer and joint movement in the review.

A published GE20ES candidate fails its life target.

In SKF’s concrete-transporter torque-support example [3], the inputs are alternating radial load 12 kN, oscillation half-angle 15°, frequency 10 min−1, maximum 80 °C, relubrication every 40 hours and a 7,000-hour rating-life target.

SKF example stageResult
Initial load screenRequired C 24 kN; GE20ES C 30 kN passes.
GE20ES life calculationAbout 160 hours with initial lubrication; about 1,500 hours with planned relubrication. Below the target.
Larger GE25ES, recalculatedAbout 7,490 hours with relubrication; meets the example target.

SKF’s example is not a supplier life guarantee. GE25ES needs a 25 mm bore, changing the 20 mm-pin installation.

Keep the offered manufacturer in the calculation.

Jingjiu [1] explicitly gives GE20ES dynamic 30 kN and static 146 kN. Wuling [2] prints the numbers 30 and 146 but gives no load unit in that table. The identical numbers do not establish equivalent ratings, wear behaviour or life. Do not attach the SKF result to either quotation.

For a retained 20 mm pin, the useful supplier answer is an assessment of its offered GE20ES against your force directions, movement, temperature, maintenance and required life or wear limit. If that assessment calls for a larger bearing, the pin and joint become part of the redesign. A quote merely repeating “30” has not answered the life question; changing the label to a larger model has not solved the retained-pin problem.

The 9° entry and the oscillation half-angle describe different movement.

Jingjiu’s row gives a° approximately 9, and its section shows the angle between the tilted bore axis and the outer-ring axis. Wuling’s original section and GE20ES row also show a 9° angle. It is an inclination entry, not the full back-and-forth angular travel of an aligned joint.

SKF’s movement diagram separately defines oscillation half-angle β; end-to-end travel is 2β. Its example’s 15° half-angle is therefore not a 15° misalignment requirement. The original diagrams [3] show the distinction.

On your joint sketch, draw the housing axis and the pin axis for the required tilt. Separately mark the two endpoints of the oscillating movement and state cycles per minute. Writing only “swings 9°” leaves two different motions possible. Keep the manufacturer’s approximate catalogue angle separate from the assembled joint’s usable movement; shoulders, covers and spacers still need to clear at the required positions.

The outer ring occupies a different axial span.

Both supplier sections assign B 16 mm to the inner ring and C 12 mm to the outer ring, with d 20 and D 35 mm. Identify which ring each shoulder or retaining face locates. A housing seat based on the headline’s 16 mm alone would ignore the published 12 mm outer-ring span. The drawing must show the retaining faces and movement clearance; neither the width difference nor the 9° entry supplies the location of an actual stop.

Jingjiu groups GE20ES with GE20ES-2RS under “requiring maintenance”; Wuling lists both designations on the same size row. The grouping confirms published variants, not an identical offered closure or a maintenance-free conversion. Keep the exact selected configuration and a workable lubrication route on the joint drawing. The inquiry below retains the GE20ES supplier records; specify a different sealed offer explicitly rather than assuming the quote includes it.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Inner-ring width B (mm)Dynamic load rating (kN)Static load rating (kN)Reference mass (kg)Source recorded
Wuling
GE20ES
203516
Wuling also lists outer-ring C 12 mm in its actual section/table.
—
No value retained here. Wuling’s source prints Dynamic C 30 and Static Co 146 without a load-unit label; these are not established as kN.
—
The source number is 146 with no stated load unit. Do not infer its unit from Jingjiu’s same-number entry.
—
Not retained in this older dataset. The source row now read lists 0.061 kg.
2026-09-24 source ↗Request
Jingjiu
GE20ES
203516
Jingjiu’s separate outer-ring width C is 12 mm.
30
Jingjiu explicitly labels this column kN. Not a life guarantee or a transferable SKF calculation.
1460.066
Jingjiu lists approximately 0.066 kg; Wuling’s source gives 0.061 kg for its own row.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

Compare the recorded figures.

PropertyFindingSources
BoreAll 2 sources publish 20 mm2
Outside diameterAll 2 sources publish 35 mm2
Inner-ring width BAll 2 sources publish 16 mm2

Where the figures differ, use the drawing from the manufacturer you buy from.

The works that publish GE20ES.

Jingjiu

Lishui, Zhejiang, China

Spherical plain bearings and linear motion

Jingjiu publishes linear-motion components, ball screws and spherical/rod-end bearings. Its spherical-bearing catalogue separates designs requiring maintenance from maintenance-free designs and labels the GE15ES/GE15ES-2RS row’s load ratings in kN. Choose the complete joint and mounting drawing, then confirm its sealing and lubrication requirements for the actual motion.

Published ranges: Lubricated and self-lubricating spherical plain bearings · Rod-end and angular-contact plain bearings · Linear ball bearings and guideways · Ball screws and supporting components

42 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Jingjiu about GE20ES

Wuling

Lishui, Zhejiang, China

Linear and spherical plain bearing systems

Wuling publishes linear-motion parts and articulating joints. Its radial spherical-plain catalogue separates ring widths and lists seal variants by exact row; specify the joint’s required movement and the complete offered construction.

Published ranges: Linear ball bearings · Stud-type needle track rollers · Rod-end and spherical plain bearings · Linear guides and sliding units

52 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Wuling about GE20ES

Applications the publishing works state.

ApplicationStated by
Machine toolsWuling
Medical machineryWuling
Printing machineryWuling
Textile machineryWuling

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for GE20ES.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Wuling · GE20ES source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. Jingjiu · GE20ES source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Jingjiu · GE20ES / GE20ES-2RS original table and section ↗

    Requiring-maintenance category. GE20ES row: dimensions in mm d20/D35/B16/C12/dk29/d1 24, approximate angle9°; explicit ratings30/146 kN and approximate mass0.066 kg. Original section shows B/C and inclination.

  2. Wuling · original GE20ES dimension table and section ↗

    GE20ES and GE20ES-2RS grouped row: dimensions mm d20/D35/B16/C12/d1min24; angle9°, mass0.061 kg. Dynamic C30/static Co146 lack a load-unit label. Separate ring spans and tilt illustrated.

  3. SKF · actual GE20ES sizing example and movement diagrams ↗

    Printed62–63: SKF sizing case/results. Printed39: oscillation diagram. Printed104: tilt and bores. Does not calculate either directory supplier’s life.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.