Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Needle roller
HK/18×25×25
HK/18×25×25 is a needle roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 18 × 25 × 25 mm. The publishing works are in Hubei province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Will replacing HK/18×25×25 also require work on the shaft raceway?
That depends on the actual bearing arrangement and shaft condition. ZXY’s own needle-bearing explanation requires shaft or housing surfaces used as raceways to meet bearing-raceway requirements. Its HK/18×25×25 row gives dimensions and mass, but no shaft finish, hardness, fit limits or named vehicle application.
An 18 mm dimension does not specify a usable shaft raceway.
ZXY’s actual HK/18×25×25 row [1] gives d = 18 mm, D = 25 mm, B = 25 mm and mass 0.032 kg. It does not specify an inner ring, a shaft raceway tolerance or a permissible wear limit. Obtain the exact item drawing to establish which surface the needles run on.
ZXY’s accompanying explanation says that, where an arrangement omits a ring, the shaft or housing surface serving as the raceway needs hardness, machining accuracy and surface quality comparable to a bearing-ring raceway. Its two series illustrations show different arrangements, but neither is an individually labelled HK/18×25×25 drawing. They cannot decide the supplied item’s construction.
Actual arrangement to establish
Evidence needed before replacement
Needles run directly on the shaft
The approved shaft-raceway drawing and an inspection against its material, surface and geometry limits; changing the bearing alone does not document the shaft’s condition.
A separate inner ring supplies the raceway
The approved inner-ring designation and dimensions, its condition, and the shaft-seat requirement for that ring. Do not infer an interchangeable ring from “18”.
The old assembly is not yet identified
A sectional drawing or clear dismantled-part identification for ZXY to confirm the rolling surface and supplied components.
SKF’s raceway explanation [2] helps define the inspection request: material and heat treatment, hardness, roughness and texture, and geometry including roundness and run-out. It supplies no model-specific ZXY acceptance limits. Ask ZXY for those limits and assess the actual shaft against them; a nominal diameter measurement alone does not cover these requirements.
Visible tracks or damage should be documented for the manufacturer’s assessment. This page has no measured shaft, sample photograph or wear criterion and therefore cannot decide whether an existing shaft should be reused, ground or replaced.
The catalogue’s vehicle and installation-position cells are blank.
ZXY’s table includes columns for vehicle model, installation position and remarks. All three cells are blank for HK/18×25×25. The manufacturer’s general mention of transmissions, universal-joint supports and rear suspensions does not identify a vehicle or gearbox that takes this item.
For automotive replacement, provide the vehicle and gearbox or assembly identifier, production version, old part markings and the controlled parts reference. Ask for written confirmation of the exact bearing position and construction. Matching 18 / 25 / 25 mm is a dimensional screen; it is not a documented vehicle fitment.
The same ZXY table explicitly writes 2RS or TN6 on some other HK rows. HK/18×25×25 has neither suffix in the examined row. That difference does not prove its sealing or cage material; request those details for the actual offer instead of borrowing an adjacent row’s suffix.
ZXY describes the examined needle-bearing range as carrying radial load only. Identify where the actual assembly carries axial force and request the offered item’s load, speed, lubricant and installed-clearance requirements. No rated load or speed appears in this row, so the compact envelope and 32 g converted catalogue mass cannot supply a load-capacity or operating-life estimate.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
3.5 mm
Mean diameter dm
(D + d) / 2
21.5 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
ZXY publishes automotive bearings, hub units and driveline components. Its needle-bearing table distinguishes complete new designations from old-code records; confirm the exact offered construction and vehicle position before choosing a replacement.
Published ranges: Automotive bearing products · Vehicle-bearing development and manufacture
12 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for HK/18×25×25.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Fresh text and exact row read, including mm/kg headers and blank fitment cells; both embedded series images actually viewed. General raceway requirements kept conditional; no model-specific ring, sealing, cage or shaft limits inferred.
PDF page 181, printed 179: raceway-property explanation read and full page rendered/viewed. Background for the inspection request; no SKF fit class or acceptance number transferred to this ZXY model.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies