ZXY explicitly lists bore 42 mm, outside diameter 49 mm and width 22 mm for HK42×49×22-2RS TN6. Its page supplies no individual controlled drawing for this row; these three dimensions do not define the delivered cage, seals, rings or mating raceway.
Needle roller
HK42×49×22-2RS
HK42×49×22-2RS is a needle roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 42 × 49 × 22 mm. The publishing works are in Hubei province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Keep TN6 on the order, and keep the 22 mm row separate from the two 24 mm records.
ZXY’s current needle-bearing table prints HK42×49×22-2RS TN6, with 42 mm bore, 49 mm outside diameter and 22 mm width. This directory’s earlier label omitted TN6. The same official table also contains two different 24 mm records, including an old-code entry with a mass number. Neither supplies a documented substitute or mass for the 22 mm part.
Three catalogue rows answer three different ordering questions.
ZXY’s official needle-bearing table [1] distinguishes new designation from old designation. The 22 mm row places HK42×49×22-2RS TN6 in the new-designation column. Its old-designation cell is blank. Retain TN6 in the enquiry and ask ZXY what it specifies for this offered part; the examined page does not define it. Another manufacturer’s suffix convention cannot establish ZXY’s cage material or temperature limit.
Exact source row [1]
Designation columns
Bore / outside / width
Weight cell
22 mm part on this page
New: HK42×49×22-2RS TN6. Old: blank.
42 / 49 / 22 mm
Only “Kg”, with no number.
Separate HK24 row
New: HK42×49×24-2RS. Old: blank.
42 / 49 / 24 mm
Only “Kg”, with no number.
Separate old-code K24 row
New: blank. Old: K42×49×24-2RS.
42 / 49 / 24 mm
0.0548 kg, for this row only.
The two 24 mm entries are separate rows. ZXY does not pair K42×49×24-2RS with HK42×49×24-2RS in one new/old-code record here. Similar lettering and matching dimensions do not establish a supersession. If a quote changes HK to K, obtain ZXY’s explicit identification of the supplied construction and any replacement relationship. Do not silently remove TN6 because a proposed 24 mm designation does not contain it.
If a supplier offers a 24 mm part: the listed width is 2 mm greater than the 22 mm record. That difference flags an axial-interface question. It is not permission to add a spacer, machine a shoulder or accept a different running clearance. Have the responsible designer compare the offered drawing with the retained shaft/housing arrangement before approving it.
Resolve the remaining order identity on one marked drawing: which rings, cage, seals and lubricant are supplied; which shaft or housing surfaces act as raceways; and what TN6 means for that construction. The category text discusses arrangements that can use a shaft or housing bore as a raceway, but it does not establish that this exact HK22 offer omits a ring or uses a particular cage. The family illustrations are not a controlled drawing of the delivered item.
The exact 22 mm row leaves vehicle and installation-position cells blank. Obtain a part-specific application confirmation for the actual vehicle or machine; the page’s general transmission and driveline uses are not vehicle-fitment approval. Its weight cell gives no numeric mass: neither zero nor the old-code K24 row’s 0.0548 kg belongs in an HK22 receiving specification.
A usable quote returns HK42×49×22-2RS TN6, an identified drawing revision and supplied-component scope. If ZXY proposes a shorter designation or a 24 mm replacement, keep the change explicit and obtain its technical explanation and your application approval. The original table alone supplies no model-specific load rating, speed limit, seal compound or operating-life result.
What each manufacturer published.
Manufacturer
Bore (mm)
Outside diameter (mm)
Width (mm)
Source recorded
ZXY HK42×49×22-2RS Current source’s full new designation: HK42×49×22-2RS TN6. The line above preserves the earlier directory label.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.
ZXY publishes automotive bearings, hub units and driveline components. Its needle-bearing table distinguishes complete new designations from old-code records; confirm the exact offered construction and vehicle position before choosing a replacement.
Published ranges: Automotive bearing products · Vehicle-bearing development and manufacture
12 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Exact HK42×49×22-2RS TN6 row: new-code column, 42/49/22 mm, mass cell only Kg, blank old code/vehicle/position. Separate HK24 and old-code K24 rows distinguish width, designation-column placement and mass attribution. Family text and illustrations do not define TN6 or the delivered HK22 configuration.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies