BearingIndex
THE BEARINGINDEX DIRECTORY

NN3006-K-W33 — 30 × 55 × 19 mm

BOUNDARY DIMENSIONSUNIT / mm

YJB identifies a 30 × 55 × 19 mm NN3006-K-W33. Its mounting drawing separates da/Da from the bore and outside diameter, and illustrates S at the ring faces. S 1.4 is not a stated radial-clearance or tapered-seat drive-up instruction. The shared section labels F even though the selected NN3006 row supplies E 48.5 mm and leaves F blank.

Cylindrical roller

NN3006-K-W33

NN3006-K-W33 is a cylindrical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 30 × 55 × 19 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
30 mm
Outside D
55 mm
Width B
19 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 30 × 55 × 19 mm NN3006 offer can still describe a different bearing.

YJB’s exact NN3006-K-W33 row and model PDF identify the same outline, but the outline alone does not settle the bore design, precision or mounting arrangement. NSK’s independently published plain NN3006 has that outline and explicitly describes a cylindrical bore and normal tolerance class. Use this concrete difference to check a shortened replacement quote, then return to YJB’s own mounting values and operating conditions.

Resolve the shortened model before treating the replacement as a match.

YJB’s selected detail page [1] and its NN3006-K-W33 PDF [2] both give bore d 30 mm, outside diameter D 55 mm and width B 19 mm. A quote reduced to “NN3006, 30×55×19” loses the remaining designation and configuration. An independently published example shows why that matters.

Actual published entryWhat the source identifiesReplacement question
YJB NN3006-K-W3330 × 55 × 19 mm; mass 0.19 kg. The examined model page does not state a numerical taper, precision class or selected radial clearance.Have YJB identify the offered bore profile, tolerance class and clearance arrangement on its own drawing.
NSK NN3006The same 30 × 55 × 19 mm outline. NSK explicitly describes this default NN3006 entry as cylindrical bore and ISO NORMAL CLASS.This separate manufacturer entry demonstrates an unresolved configuration difference. It is not an approved replacement for YJB’s complete designation.

The NSK page [3] is a comparison source, not another supplier record for this YJB model. Its properties cannot define what YJB means by K or W33, nor can its normal tolerance class be assigned to the YJB offer. Equally, a precision-family heading on YJB’s site does not select a numerical tolerance class for the delivered bearing.

Return a shortened quotation with the full required name NN3006-K-W33 and the existing bearing-seat drawing. Ask the seller to mark any change in bore geometry, precision or internal-clearance specification and explain the resulting mounting procedure. If the seller actually proposes a plain NN3006, compare that proposed manufacturer’s exact drawing with the old seat before accepting it. Keeping the 30/55/19 outline unchanged does not resolve those questions.

The 38 and 50 installation entries describe different interfaces from d 30 and D 55.

YJB’s installation sketch [4] places da and Da at the surrounding shaft/housing abutments and ra1 at a corner. Keep those callouts separate when checking the old mounting drawing. In particular, da h12 38 does not change this bearing’s nominal 30 mm bore.

YJB NN3006-K-W33 entryRead it with the drawingWhat to return with the enquiry
d 30 / D 55 / B 19 mmThe bearing’s nominal outline, in the dimensions-mm group.Actual seat geometry and fits; the row does not supply a complete shaft-seat machining specification.
da h12 38 / Da H12 50Entries under installation dimensions. The lower-case and capital callouts refer to different mounting surfaces; the group does not separately state its unit.Marked abutment diameters and their units. Do not transfer h12/H12 to d or D.
ra1 1 / S 1.4ra1 is shown at the mounting corner; S is shown between ring-face positions. The selected source does not explicitly define S’s unit or allowable operating movement.Corner clearance, locating faces and the manufacturer’s definition of S. Do not use 1.4 as a radial-clearance or drive-up target.
E 48.5 mm / F —The selected row supplies E, while the shared series section labels F. The blank F entry is not zero.A controlled NN3006-K-W33 section identifying E; do not relabel E 48.5 as F 48.5.

There is also a concrete cross-brand abutment difference: the separate NSK NN3006 page specifies da minimum 35 mm, while YJB lists da h12 38 in its installation group. These have different stated qualifiers as well as different numbers. Do not replace YJB’s 38 with NSK’s 35 or treat either as a universal NN3006 shaft-shoulder rule.

For an existing 30 mm spindle seat, attach a section showing the shoulder, spacer, retaining arrangement and housing corner. Ask YJB to return the selected drawing with d, da, D, Da, ra1 and S marked and the units confirmed. That comparison can identify an actual interference or locating mismatch; merely measuring the outside envelope cannot. No machining tolerance, permissible axial travel or tapered-seat adjustment is inferred from the catalogue sketch.

A 17,000-speed proposal needs the actual lubrication conditions and confirmed units.

YJB’s selected webpage and model PDF print nG脂 16000 and nG油 19000 under “极限转速 min”. The website does not explicitly print revolutions per minute in that heading, and its oil column does not name oil-bath or oil-air delivery. The PDF repeats these labels; downloading it does not settle the missing definitions.

If a quotation proposes operation at 17,000, specify that you mean 17,000 r/min and ask YJB to assess the offered bearing and lubricant arrangement at that condition. Simply putting the requested number between 16000 and 19000 assumes their intended unit and treats an unspecified oil entry as operating approval. Both assumptions need the manufacturer’s answer, including actual oil delivery or grease specification, load, temperature and mounting condition.

Another NN3006 speed table is not a substitute. NSK’s separate default NN3006 lists grease 12000 and oil-bath 14000 min−1. It names the oil method and rotational unit explicitly. Those numbers belong to that different entry and cannot fill the conditions of YJB’s 19000 oil number.

The YJB load table has a separate issue: it labels Cr “KN” alongside 29000 and Cor “KN” alongside 34000. Preserve that unit-and-number discrepancy for confirmation; do not silently publish 29/34 kN, change the header to N or calculate a life estimate from it. A second Cr on the same page is radial stiffness, explicitly 680 N/μm. It has a different physical meaning from the basic dynamic load rating, and is not another load capacity or an allowable measured spindle deflection.

Ask YJB to return a specification for the exact offered NN3006-K-W33 with corrected load units, an explicit rotational-speed unit and lubricant method, followed by its mounting and clearance procedure for the submitted drawing. Use those confirmed inputs for the actual operating assessment. Until that reply resolves the conditions, the historical directory speed numbers below remain reference entries with the unit limitation displayed beside them.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)YJB grease speed — source number (unit unconfirmed)YJB oil speed — source number (unit unconfirmed)Reference mass (kg)Source recorded
YJB
NN3006-K-W33
30551916000
Historical record interpreted this as rpm. YJB’s current detail page and model PDF print nG脂 16000 under “极限转速 min”, without an explicit revolutions-per-minute unit. Confirm the intended unit and offered lubrication configuration.
19000
Historical record interpreted this as rpm. YJB prints nG油 19000 under the same incomplete “min” speed heading. It does not specify oil-bath or oil-air here; do not borrow another brand’s lubrication definition.
0.192026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish NN3006-K-W33.

YJB

Hangzhou, Zhejiang, China

Precision spindle and machine-tool bearings

YJB publishes precision angular-contact, double-row cylindrical roller and ball-screw bearing ranges. Its NN3006-K-W33 catalogue separates bearing dimensions from mounting callouts. Confirm the offered bore, precision and lubrication configuration against the actual spindle drawing.

Published ranges: Angular contact ball bearings · Cylindrical roller bearings · Double-direction thrust angular contact bearings · Tapered roller and nonstandard designs

740 designations documented here · 1 reviewed evidence record · source recorded 2026-10-07

Ask YJB about NN3006-K-W33

Applications the publishing works state.

ApplicationStated by
Instrument motorsYJB
Machine-tool spindlesYJB
Medical equipmentYJB
RoboticsYJB

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for NN3006-K-W33.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YJB · NN3006-K-W33 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YJB · exact NN3006-K-W33 detail ↗

    Exact model entry actually read: outline, mass, E/F, mounting callouts, S, load labels, grease/oil speed labels and radial stiffness. No taper, precision class or speed approval inferred.

  2. YJB · NN3006-K-W33 model PDF ↗

    One-page original PDF actually extracted and viewed in the browser. It repeats the model values and KN/min labels rather than resolving their unit questions.

  3. NSK · NN3006 series, default NN3006 entry ↗

    Separate manufacturer comparison actually read: default NN3006 has the same outline, cylindrical bore, normal tolerance class, da minimum 35 mm and explicitly labelled grease/oil-bath speed values. Not a YJB interchange approval or a supplier for this exact model.

  4. YJB · linked installation illustration ↗

    Original 600×600 image actually viewed. Separates installation da/Da/ra1 and illustrates S at ring faces; does not establish a complete model-specific machining or clearance procedure.

  5. YJB · linked NN/NNU series section ↗

    Actual original section labels F and depicts two arrangements. The selected NN3006 row has E 48.5 mm and F blank; the illustration is not used to relabel that value.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.