BearingIndex
THE BEARINGINDEX DIRECTORY

NN49/500-S-K-M-SP — 500 × 720 × 167 mm

BOUNDARY DIMENSIONSUNIT / mm

YJB names this 500×720×167 mm, 214 kg row NN49/500-S-K-M-SP. Its additional E664/ns23.5/ds12 mm entries and S11.7 reference need the selected drawing. A separate Schaeffler NN30/500-AS-K-M-SP row shares the three sizes but uses a different designation and ds12.5 mm; the match is not an interchangeability approval.

Cylindrical roller

NN49/500-S-K-M-SP

NN49/500-S-K-M-SP is a cylindrical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 500 × 720 × 167 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
500 mm
Outside D
720 mm
Width B
167 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Confirm the complete YJB designation and ds12 interface before ordering this 500 mm bearing.

YJB publishes NN49/500-S-K-M-SP at 500×720×167 mm and 214 kg. Its table adds E664, ns23.5 and ds12 mm, plus installation references and S11.7. A separate Schaeffler NN30/500-AS-K-M-SP publication shares the principal sizes but has a different name and ds12.5 mm. The YJB row also needs clarification of load and speed headings. Keep those questions with the offered drawing and quotation before replacing a large precision bearing.

The same 500×720×167 size appears under a different official designation.

YJB’s current exact row [1] is named NN49/500-S-K-M-SP. Keep that source identity in the enquiry. Schaeffler’s separate SP1 row [2, p.154] provides a useful geometric comparison, rather than permission to rename YJB’s part or declare the names interchangeable.

PublicationComplete designation and shared dimensionsAdditional source geometry
YJB [1]NN49/500-S-K-M-SP; d/D/B 500/720/167 mm; mass214 kg.E664, ns23.5, ds12 mm.
Schaeffler [2]NN30/500-AS-K-M-SP; d/D/B 500/720/167 mm; mass214 kg.E664, ns23.5, ds12.5 mm.

The ds entries differ by 0.5 mm. The two publishers’ matching main dimensions and mass therefore do not establish the same detailed interface. Send YJB the exact old-part marking and its controlled drawing, and ask for written identification of the offered geometry and lubrication features. Do not silently change YJB’s designation or use another supplier’s ds12.5 for the YJB quotation.

The full suffix also belongs in that confirmation. Schaeffler’s row is not YJB’s suffix dictionary, tolerance specification or material certificate. Ask YJB to identify the offered bore geometry, cage and precision requirements on its own document. An unverified interpretation of K/M/SP cannot release machining or an installed setting.

YJB lists E664, while its shared series section labels F.

The exact YJB row gives E664 mm and a dash for F. Its shared series sections [3] label F on the depicted diameter, rather than E. Obtain the selected NN49/500 drawing to identify the measured interface; do not fill the dash with 664 or treat E and F as interchangeable letters.

YJB source reference [1]Published entryWhat the selected drawing must resolve
r1 / ns / ds6 / 23.5 / 12Identify the bearing corner and lubrication-feature geometry, with their selected tolerances.
S11.7S is a separate source column. Confirm its unit, starting faces and applicable installed relationship; it is not a published preload setting.
da h12 / Da H12564 / 677Retain h12/H12 exactly; obtain units, limiting dimensions and the mating-shoulder locations.
ra16Obtain the selected limit and unit for this mounting feature, separately from bearing r1.

YJB’s mounting view [4] shows S between relative end faces and a separate da/Da/ra1 seating sketch. These labels help frame the enquiry but do not supply a selected bore taper, axial drive-up distance or radial-clearance reduction procedure. Do not turn S11.7 into an instruction to push the ring by that amount.

The adjacent YJB NNU49/500-K-W33 row is 500×670×170 mm and 162 kg, with F568 rather than this row’s E664. Sharing a 500 mm bore is insufficient for that substitution. Use the actual inner/outer-ring support and mating dimensions, then obtain the supplier’s adjustment and inspection procedure for the offered assembly.

Resolve the load and speed headings before applying these values to a machine.

The current YJB detail [1] prints dynamic “Cr KN” with 2650000 and static “CorKN” with 5850000. Keep those as source entries pending clarification. This page does not relabel the numbers N or divide them by 1000 on the assumption that a header is wrong. Obtain a corrected, part-specific load definition and unit from YJB before using them in a calculation.

The grease/oil columns nG list 1000/1300, but their group heading is “limiting speed min”, without the complete rotational unit. The directory retains its historical numbers and explicitly marks that unit unresolved. Request confirmation of the rotational unit, offered lubrication system and applicable operating conditions before treating 1000 or 1300 as rpm limits.

Cr appears with two different meanings. The source also labels radial stiffness “Cr N/μm” and gives 10060. That entry is stiffness, not the dynamic-load figure. Ask for the selected load/clearance and calculation conditions; it is not a measured installed spindle stiffness or a positioning-accuracy guarantee.

Keep these three evidence questions separate: corrected load units, complete speed units and the stiffness basis. A supplier response should identify the same offered designation and drawing revision for all three, together with the required bearing setting and operating duty. For this published 214 kg assembly, also obtain the supplied component masses and handling instructions; the catalogue mass does not itself define an approved lift point or installation method.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Grease speed entry — unit unconfirmedOil speed entry — unit unconfirmedReference mass (kg)Source recorded
YJB
NN49/500-S-K-M-SP
5007201671000
Current YJB heading says limiting speed min, without a complete rotational unit; obtain its corrected unit and duty conditions.
1300
Same incomplete min heading; the historical number remains a source entry, not confirmed rpm.
2142026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish NN49/500-S-K-M-SP.

YJB

Hangzhou, Zhejiang, China

Precision spindle and machine-tool bearings

YJB publishes precision angular-contact, double-row cylindrical roller and ball-screw bearing ranges. Its NN3006-K-W33 catalogue separates bearing dimensions from mounting callouts. Confirm the offered bore, precision and lubrication configuration against the actual spindle drawing.

Published ranges: Angular contact ball bearings · Cylindrical roller bearings · Double-direction thrust angular contact bearings · Tapered roller and nonstandard designs

740 designations documented here · 1 reviewed evidence record · source recorded 2026-10-07

Ask YJB about NN49/500-S-K-M-SP

Applications the publishing works state.

ApplicationStated by
Instrument motorsYJB
Machine-tool spindlesYJB
Medical equipmentYJB
RoboticsYJB

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for NN49/500-S-K-M-SP.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YJB · NN49/500-S-K-M-SP source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YJB · Exact NN49/500-S-K-M-SP row ↗

    500/720/167 mm, 214 kg, r1 6/E664/ns23.5/ds12 in the mm group; F dash, separate S11.7 and mounting references. Load headings KN with 2650000/5850000, speed heading min with grease1000/oil1300, and a distinct radial-stiffness Cr10060 N/μm need the selected definitions and applicable conditions.

  2. Schaeffler · SP1, separate NN30/500-AS-K-M-SP geometry ↗

    Printed/PDF p.154: separate designation NN30/500-AS-K-M-SP, 214 kg, d/D/B500/720/167 mm, E664/ns23.5/ds12.5 mm. Geometric comparison only; it does not correct YJB’s name or approve a substitution.

  3. YJB · NN/NNU shared series sections ↗

    Two series sections label d/D/B, F, r1 and lubrication references ns/ds. Their F label does not resolve the exact row’s E664/F dash.

  4. YJB · Series mounting and relative-face view ↗

    S relative-face reference and da/Da/ra1 seating geometry; obtain the selected units, datums, tolerances and adjustment procedure.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.