BearingIndex
THE BEARINGINDEX DIRECTORY

NNCF5004CV — 20 × 42 × 30 mm

BOUNDARY DIMENSIONSUNIT / mm

Wanda’s double-row full-complement NNCF5004CV has a 20×42×30 mm envelope and an additional s 1 mm entry on its semi-locating section. The section also labels bearing chamfer r min 0.6 mm. Check the locating/displacement direction, initial ring position and mating shoulders; three size numbers do not define the axial arrangement.

Cylindrical roller

NNCF5004CV

NNCF5004CV is a cylindrical roller designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 20 × 42 × 30 mm. The publishing works are in Jiangsu province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
20 mm
Outside D
42 mm
Width B
30 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Check the s1 axial interface and the 7300/10500 speed headings separately.

Wanda identifies NNCF5004CV as a double-row full-complement bearing in its semi-locating NNCF range. The exact row adds s 1 mm to the 20×42×30 mm dimensions and lists 7300 r/min reference speed versus 10500 r/min limiting speed. Those are not grease and oil columns. Selection needs the intended axial arrangement and an operating assessment, rather than approval from the envelope or the larger speed alone.

The s1 entry needs a direction and a starting position on the assembly drawing.

Wanda’s exact NNCF5004CV row and section [1] identify a semi-locating, double-row full-complement bearing. The section marks s at the ring relationship near one end; the row gives s 1 mm. It is a different requirement from the 20 mm shaft bore, 42 mm outside diameter or 30 mm width.

Wanda’s selected entryNNCF5004CV valueResolve on the drawing
Principal d / D / B20 / 42 / 30 mmCheck the offered ring fits and seating, rather than use the nominal envelope as a complete installation specification.
Section reference s1 mmAsk Wanda to identify the permitted direction, defined initial ring position and available movement after assembly.
r in the row / r min on section0.6 mmObtain the permissible shaft/housing shoulder corner and diameters; a bearing chamfer reference is not that permission.

A requirement for 1 mm movement in both directions is not established by this single s entry. If the shaft has a fixed support at the other end, identify which direction its thermal movement takes relative to this bearing. Ask Wanda to mark the installed ring position and movement limits before fixing the mating shoulders and retention.

As design background, SKF’s NNCF explanation [2, printed p.501] describes one-direction axial location with movement toward the other direction and a retaining ring that must not carry operating axial load. That is SKF’s design guidance; have Wanda confirm the selected NNCF5004CV’s load path and retention details. Do not use a retaining feature as an unverified thrust stop.

The two roller rows do not turn this semi-locating section into a bearing that locates both directions. Likewise, s1 is not a radial-clearance class or an instruction to create 1 mm radial play. Request the selected clearance and fits independently, plus the tolerances and displacement datum on the offered drawing.

9000 r/min is between the two entries, which calls for an operating assessment.

Exact Wanda table heading [1]NNCF5004CV entryUse the stated meaning
Reference speed7300 r/minThe table does not call this a grease speed.
Limiting speed10500 r/minThe table does not call this an oil speed or a tested continuous duty.
Dynamic C / static C053 / 53 kNKeep both ratings and their definitions; equal numbers are not a combined 106 kN load.
Mass0.20 kgMass does not define the permitted installed load or movement.

For a 9000 r/min requirement, the requested speed is higher than Wanda’s 7300 reference entry and lower than its 10500 limiting entry. That comparison identifies a question for engineering review; it does not approve the application merely because 9000 is below the larger number. Provide the load, lubrication, temperature and cooling conditions and obtain Wanda’s applicable assessment.

SKF’s speed guidance [2, printed p.135] distinguishes thermal reference speed from mechanical limiting speed and calls for assessment of actual load, viscosity and heat dissipation. This explains why two speed headings matter; SKF’s reference conditions do not establish Wanda’s calculation basis or validate its 10500 entry for this installation. Ask Wanda to state its own conditions and permitted operating duty.

The catalogue’s C and C0 entries are both 53 kN. Neither entry is explicitly a permissible axial load on the flange/retention arrangement, and their equality does not make them interchangeable limits. Give Wanda the force direction and combined duty for the intended semi-locating installation; obtain the allowable axial operating load separately from the catalogue’s basic ratings.

Keep the complete NNCF5004CV designation in the quote, controlled drawing and inspection record. Do not substitute a different NNC/NNCL arrangement from the three-number envelope, or attach a grease/oil speed pair by convention. The offered design must retain the required axial function and operating conditions together.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Dynamic load rating (kN)Static load rating (kN)Bearing chamfer r min (mm)Reference mass (kg)Source recorded
Wanda
NNCF5004CV
20423053530.6
Wanda’s series section labels bearing chamfer r min; this is not the permissible mating-shoulder radius.
0.22026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish NNCF5004CV.

Wanda

Nantong, Jiangsu, China

Forklift bearings and slewing supports

Wanda publishes forklift rollers, full-complement cylindrical roller bearings and slewing bearings. Its NNCF table separates axial-displacement geometry from reference and limiting speeds; specify the complete bearing, mating interfaces and installed-duty assessment for the offered configuration.

Published ranges: Forklift mast and side-roller bearings · Chain and combined-roller bearings · Full-complement cylindrical roller bearings · Slewing bearings

82 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Wanda about NNCF5004CV

Applications the publishing works state.

ApplicationStated by
Construction equipmentWanda
ForkliftsWanda
Industrial robotsWanda
Logistics equipmentWanda

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for NNCF5004CV.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Wanda · NNCF5004CV source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Wanda · Exact NNCF5004CV row, speed headings and semi-locating section ↗

    Double-row full-complement, semi-locating NNCF: d/D/B: 20/42/30 mm; r 0.6/s 1 mm; C/C0: 53/53 kN; reference speed 7300 and limiting speed 10500 r/min; mass 0.20 kg. The section labels s and bearing r min, without a complete selected assembly datum or shoulder specification.

  2. SKF · Rolling bearings: NNCF design and speed definitions ↗

    Printed p.501 (PDF503): NNCF directional location/displacement and retaining-ring guidance. Printed p.135 (PDF137): thermal reference versus mechanical limiting speed and application assessment. Technical background, not approval of Wanda’s supplied part.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.