BearingIndex
THE BEARINGINDEX DIRECTORY

NNCF5005CV — 25 × 47 × 30 mm

WANDA DIRECTORY RECORDUNIT / mm

These are Wanda’s recorded principal dimensions. They do not specify the shaft-shoulder diameter, mating fillet or axial-load support. A matching SKF designation needs its own mounting data; do not combine the two brands into one specification.

Cylindrical roller

NNCF5005CV

NNCF5005CV is a cylindrical roller designation documented on BearingIndex from 1 manufacturer publication. The listed Wanda bearing has a 25 mm bore, 47 mm outside diameter and 30 mm width. The drawing check below concerns SKF’s separately published NNCF 5005 CV and does not release a Wanda mounting arrangement. The publishing works are in Jiangsu province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
25 mm
Outside D
47 mm
Width B
30 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 30 mm shoulder clears one SKF 5005 check, but falls short of its axial-load support recommendation.

For a selected SKF NNCF 5005 CV, the mounting table gives two different shaft-shoulder values: da min 28.7 mm and recommended das 31.5 mm for axial loading. A drawing with a 30 mm shoulder therefore needs more than a tick against the minimum diameter. The worked check below shows what to mark and what remains unresolved. This is an illustrative drawing, not a measured customer installation. The supplier record on this page is Wanda’s NNCF5005CV; SKF’s mounting values are kept separate.

Mark the loaded contact face before approving the shaft drawing.

Illustrative inputs: SKF NNCF 5005 CV, a 25 mm shaft seat, a 30 mm shaft shoulder, and an application that loads the inner-ring flange axially. Only the bearing dimensions and SKF recommendations below are catalogue facts; the proposed shoulder and duty are example inputs.

1. The minimum-diameter check passes.

The SKF 25 mm mounting row [1] gives da min 28.7 mm. The example shoulder is 30 − 28.7 = 1.3 mm above that minimum, calculated as a diameter difference. That answers the minimum-abutment comparison. It does not answer whether the same contact face follows the recommendation for an axially loaded flange.

2. The loaded-support recommendation is not met by that number.

The same row gives das 31.5 mm, with a footnote identifying it as the recommended shaft abutment diameter for axially loaded bearings. The example 30 mm shoulder is 31.5 − 30 = 1.5 mm smaller in diameter. This is why checking only 28.7 mm would leave the axial-support decision incomplete.

Keep “recommended” on the drawing review: 31.5 mm is not a published minimum axial-force rating, and reaching it does not establish an approved operating load. SKF’s flange-support explanation [2] also calls attention to the supporting face and total axial runout. The flange should be supported only up to half its height. Simply making a shoulder as large as possible is not the stated approach.

Return the drawing with the actual contact face identified, rather than just changing an outside-diameter callout. Show the shoulder, any intervening spacer and the inner-ring flange in section. If a spacer provides the bearing contact, its contact geometry needs review; the diameter of a shaft shoulder elsewhere is not a substitute for that interface. Record the axial force direction with that section so the support review follows the loaded flange.

3. Check the corner independently.

SKF lists bearing chamfer r1,2 min 0.6 mm and adjacent-part fillet ra max 0.5 mm in separate columns. An illustrative shaft drawing calling for a 0.6 mm fillet exceeds that 0.5 mm entry by 0.1 mm. It cannot be cleared merely because the bearing-chamfer number is also 0.6.

Retain the distinction between the bearing corner and the shaft or housing corner on the drawing. The same SKF row has housing abutment Da max 43.5 mm; this is a separate housing-side check, not another permissible shaft diameter. The review needs the contacting faces, the applicable fillets and their tolerances together.

Result of this example: the 30 mm shoulder passes the stated da minimum comparison; it falls short of the published axial-load recommendation. The proposed 0.6 mm mating fillet also exceeds the separate ra maximum. Neither changing the shoulder to 31.5 mm nor correcting one corner alone releases the complete assembly.

Use the example to find missing drawing information, not to machine for another brand.

The actual Wanda NNCF5005CV record [3] is 25 × 47 × 30 mm and gives r 0.6 mm and s 1 mm. Its section [4] identifies r min at the bearing corner. The examined publication does not give this model’s shaft abutment diameter, permissible mating fillet or axial-load support recommendation.

If Wanda is the part being purchased, the SKF example therefore identifies what is missing from the installation review; it does not establish whether a 30 mm shoulder is acceptable for Wanda. Retain the actual shaft and housing section, identify the axial force and contact faces, and obtain Wanda’s requirements for those interfaces. Keep its approved values with the order drawing. Do not print “das 31.5 / ra 0.5” as Wanda specifications.

Conversely, if the order explicitly selects SKF NNCF 5005 CV, review the SKF dimensions against the current selected drawing and complete load assessment. The directory inquiry below addresses Wanda’s listed product 2779, not an offer of SKF stock. Keep the bearing identity on the drawing and purchase order so a later brand substitution triggers a new interface review.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Dynamic load rating (kN)Static load rating (kN)Bearing chamfer r min (mm)Reference mass (kg)Source recorded
Wanda
NNCF5005CV
25473060650.6
Wanda labels this as bearing chamfer r min. Its 0.6 mm value is not an allowable shaft-shoulder fillet; the separate SKF ra max 0.5 mm applies only to the examined SKF bearing.
0.232026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish NNCF5005CV.

Wanda

Nantong, Jiangsu, China

Forklift bearings and slewing supports

Wanda publishes forklift rollers, full-complement cylindrical roller bearings and slewing bearings. Its NNCF table separates axial-displacement geometry from reference and limiting speeds; specify the complete bearing, mating interfaces and installed-duty assessment for the offered configuration.

Published ranges: Forklift mast and side-roller bearings · Chain and combined-roller bearings · Full-complement cylindrical roller bearings · Slewing bearings

82 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Wanda about NNCF5005CV

Applications the publishing works state.

ApplicationStated by
Construction equipmentWanda
ForkliftsWanda
Industrial robotsWanda
Logistics equipmentWanda

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for NNCF5005CV.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Wanda · NNCF5005CV source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. SKF · NNCF 5005 CV mounting dimensions ↗

    Printed p.565, 25 mm row: da min28.7, das31.5 with axial-load recommendation footnote, Da max43.5, bearing r1,2 min0.6 and ra max0.5 mm. Model identity and 25/47/30 mm are on preceding printed p.564.

  2. SKF · flange support ↗

    Printed p.512: support surfaces and total axial runout for axial loading; inner flange supported to half height. Full-complement das values are in product tables.

  3. Wanda · NNCF5005CV original row ↗

    25/47/30 mm, r0.6 and s1 mm; C60/C065 kN; reference6100/limiting9000 r/min;0.23 kg. No selected-model mating-shoulder limits in this publication.

  4. Wanda · NNCF section ↗

    Original bearing section labels d/D/B, s and r min. It does not dimension the shaft-shoulder contact face.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.