BearingIndex
THE BEARINGINDEX DIRECTORY

SF692 — 2 × 6 × 2.3 mm

BOUNDARY DIMENSIONSUNIT / mm

Runstar’s open SF692 detail explicitly gives a 2 mm bore, 6 mm body outside diameter, 2.3 mm width, 7.5 mm flange outside diameter and 0.6 mm flange thickness. The 2 × 6 × 2.3 directory key does not include the flange. Use the five dimensions below and the offered drawing when reviewing the seat.

Ball bearings

SF692

SF692 is a ball bearings designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 2 × 6 × 2.3 mm. The publishing works are in Fujian province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
2 mm
Outside D
6 mm
Width B
2.3 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Adding a shield or seal changes more than the SF692 closure.

Runstar identifies SF692 as open, with width 2.3 mm and flange thickness 0.6 mm. Its SF692ZZ and SF692-2RS details retain the 2 mm bore, 6 mm body OD and 7.5 mm flange OD, but give width 3 mm and flange thickness 0.8 mm. Review both axial changes against the original seat before changing the complete designation.

Compare width and flange thickness separately.

Manufacturer fieldSF692 [1]SF692ZZ [2]SF692-2RS [3]
Closure stated in detailOpenShieldsRubber seals
Bore2 mm2 mm2 mm
Body outside diameter6 mm6 mm6 mm
Flange outside diameter7.5 mm7.5 mm7.5 mm
Width B2.3 mm3 mm3 mm
Flange thickness0.6 mm0.8 mm0.8 mm

The closed variants add 0.7 mm to the published width and 0.2 mm to the published flange thickness. These are differences between catalogue entries, not measured samples, available axial clearance or permitted tolerances. The open detail [1], shielded detail [2] and rubber-sealed detail [3] explicitly state millimetres. The list’s bare dimension numbers are not the unit evidence.

If the original seat locates the open SF692 by its flange face, mark that face and the opposing locating surface on your assembly drawing. Ask Runstar to show the B and flange-thickness datums for the proposed ZZ or 2RS drawing, then check the actual locating positions. Do not assume the 0.7 mm width difference is spare clearance, or subtract flange thickness from B to invent a machining depth: the web table supplies neither a controlled section drawing nor the relevant tolerances.

The 6 mm body OD and 7.5 mm flange OD are distinct interfaces. A 692 record sharing the directory’s 2 × 6 × 2.3 key does not establish the same complete envelope or the flange locating feature. The three-number match alone contains no flange geometry evidence. The site therefore does not recommend it as a same-envelope candidate here. Runstar’s own cross-reference table is a supplier mapping; no independently checked replacement drawing or installed interchange approval was obtained.

Keep the open SF692’s weight and closure evidence attached to their original fields.

Unresolved SF692 mass: the current list and the top of its detail say 0.28 g; the same detail’s weight(g) row says 0.35 g. The directory retains its historical 0.00028 kg value with this conflict flagged. Neither source position is treated as the confirmed order mass.

Send the two locations in the SF692 detail [1] and the exact list row [4] to Runstar and request a corrected, revision-controlled specification for the open part. Ask whether the value is the individual bearing’s mass and which construction it describes. Do not average the two values or borrow a closed variant’s weight to settle the open record.

The open detail also contains a “shields material” entry of stainless steel 304 alongside its explicit “Seal type: Open”. That material field does not prove the SF692 offer includes shields. Keep SF692 open explicit in the order, and have any proposed cover or seal change identified by the complete designation and its changed width/flange thickness. The same-page photograph and the category’s material options do not replace that configuration statement.

Its ISO9001:2015, REACH and ROHS rows display “PASSED”. The examined entry provides no linked candidate-specific report or current certificate evidence for those rows. If such evidence is needed for the order, request the document identifying the supplied construction and applicable scope; the word alone is not a verified result for your lot.

What each manufacturer published.

ManufacturerReference mass (kg)Source recorded
Runstar
SF692
0.00028
Historical 0.00028 kg = 0.28 g. Current SF692 list/top says 0.28 g; detailed table says 0.35 g. Unresolved source conflict.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

The works that publish SF692.

Runstar

Zhangzhou, Fujian, China

Miniature ball and thrust bearings

Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.

Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs

223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Runstar about SF692

Applications the publishing works state.

ApplicationStated by
Fishing tackleRunstar
Medical equipmentRunstar
Precision instrumentsRunstar
Small motorsRunstar

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for SF692.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Runstar · SF692 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Runstar · SF692 open detail ↗

    Exact SF692 identity/Open, five dimension fields with mm, 0.28 g top versus 0.35 g detailed weight, and parallel shields-material/PASSED fields. Not a controlled assembly drawing or verified lot report.

  2. Runstar · SF692ZZ shielded detail ↗

    Exact shielded variant: 2/6/3 mm, flange OD7.5 mm, thickness0.8 mm. Used to identify the proposed axial changes; not approved as a drop-in replacement.

  3. Runstar · SF692-2RS rubber-sealed detail ↗

    Exact rubber-sealed variant: 2/6/3 mm, flange OD7.5 mm, thickness0.8 mm. Seal compound, duty approval and interchange testing not established.

  4. Runstar · metric flanged miniature list ↗

    Exact SF692, SF692ZZ and SF692-2RS rows; SF692 weight0.28 g. Bare dimension columns lack unit labels; mm comes from each exact detail above.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.