BearingIndex
THE BEARINGINDEX DIRECTORY

SG15-10 — 5 × 17 × 8 mm

ROLLER BODY / RAIL SIZE SEPARATEUNIT / mm

The 5 × 17 × 8 mm record does not describe the rail interface or the whole axial span. Runstar separately lists a 10 mm suitable rail and B1 9.75 mm wider inner ring. No groove section or mounting tolerance was found in these exact Runstar detail pages.

Track rollers

SG15-10

SG15-10 is a track rollers designation documented on BearingIndex from 1 manufacturer publication. Runstar lists SG15-10 with a 5 mm bore, 17 mm outside diameter, 8 mm body width and suitability for a 10 mm rail. Its SG15 shares the three body numbers but is listed for a 6 mm rail. Runstar gives the wider inner-ring width B1 as 9.75 mm. The publishing works are in Fujian province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
5 mm
Outside D
17 mm
Width B
8 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

The “10” is the listed rail size; the mounting bore remains 5 mm.

For Runstar’s SG15-10, separate the roller’s mounting hole from the rail it runs on. The manufacturer lists a 5 mm bore and a 10 mm suitable rail. Its SG15 retains the 5 × 17 × 8 mm body dimensions but lists a 6 mm rail. There are also two SG15-10 detail pages, labelled “shields” and “Rubber seal”; quoting the model alone leaves that choice open.

Keep the rail size in the replacement comparison.

The Runstar shielded SG15-10 [1] and rubber-sealed SG15-10 [2] both explicitly list “suitable rail size” 10 mm. The SG15 detail page [3] lists 6 mm. Their d, D and B entries alone do not reveal this difference.

Runstar designationMounting bore dOutside D / body BListed suitable rail
SG15-105 mm17 / 8 mm10 mm
SG155 mm17 / 8 mm6 mm

Retaining a nominal 10 mm rail: SG15-10 is the Runstar catalogue choice matching that stated rail size. SG15 is not a catalogue-equivalent rail match even if it fits the same nominal 5 mm mounting pin and appears to occupy the same body space. For a retained nominal 6 mm rail, the cited SG15 entry supplies the corresponding rail-size match instead. A worn rail measurement is not a new nominal size; compare it with the machine’s rail specification.

If changing the rail from 6 to 10 mm while retaining the pin, the equal bore does not establish the roller/rail contact position in the carriage. The exact Runstar pages give no groove section, roller-to-rail centre distance or adjustment range. Keep the rail and carriage drawing in the change review; this publication does not establish that the larger rail can be fitted by swapping the roller alone.

These entries identify a nominal rail match, not clearance, preload or permissible load. They do not specify a compatible flat track or establish a groove radius. Use the stated rail size rather than calculating a groove from D 17 and d 5.

“SG15-10” alone can name two different Runstar closures.

Runstar labels detail 6134181 [1] “shields” and detail 6134183 [2] “Rubber seal”. Both have d 5, D 17, B 8, B1 9.75 mm, suitable rail 10 mm and mass 9 g. Neither dimensional matching nor the model string separates those two offers.

For a replacement whose existing specification requires shields, quote Runstar SG15-10, shields, detail 6134181. For the manufacturer’s rubber-sealed form, quote Runstar SG15-10, Rubber seal, detail 6134183. These are descriptions from the actual pages, not invented order suffixes. Keep the chosen publication link with the quotation so the supplier cannot answer only with the common size.

The shielded page’s gallery also includes images used on the rubber-sealed page. A catalogue image therefore does not identify the ordered closure by itself. Check the offered part’s drawing and identification against the selected description; do not treat every image in that gallery as a separate verified configuration.

Do not clamp the mounting assembly to the 8 mm body number alone.

Runstar separately calls B1 9.75 mm the wider inner-ring width. It exceeds the stated B 8 mm by 1.75 mm, calculated from those figures. When reviewing the mounting pin and inner-ring spacer or clamp, carry the 9.75 mm span onto the assembly check. The pages do not locate each inner-ring face relative to the groove; the difference does not establish two equal 0.875 mm projections or an approved spacer thickness.

A different manufacturer’s SG15-10 is not a source for the missing Runstar geometry. The Motion drawing and exact row [4] use C 8 mm for the wider outer-ring span and B 5.75 mm for the inner-ring span. This is a different published section, despite the common designation, d 5, D 17 and 10 mm rail. Its drawing, 60° geometry and load figures do not become Runstar specifications.

The selected closure still needs its own operating basis. The examined Runstar entries do not publish a limiting speed or load rating for either form. Their dimensions cannot choose a closure for coolant, temperature or the required running resistance. State those actual requirements with the selected part; do not substitute Motion’s ratings or a generic shield-versus-seal claim for a Runstar approval.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Reference mass (kg)Source recorded
Runstar
SG15-10
5178
Runstar labels this B 8 mm and separately lists wider inner-ring B1 9.75 mm. The 8 mm entry is not the full inner-ring span.
0.009
Runstar lists 9 g, converted here to 0.009 kg. Its two SG15-10 detail pages have the same nominal figures but different closure descriptions.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish SG15-10.

Runstar

Zhangzhou, Fujian, China

Miniature ball and thrust bearings

Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.

Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs

223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Runstar about SG15-10

Applications the publishing works state.

ApplicationStated by
Fishing tackleRunstar
Medical equipmentRunstar
Precision instrumentsRunstar
Small motorsRunstar

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for SG15-10.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Runstar · SG15-10 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Runstar · SG15-10, shields ↗

    Exact description shields; d 5/D 17/B 8/B1 9.75 mm; suitable rail 10 mm; mass 9 g. Gallery includes some images also used on the rubber-sealed page.

  2. Runstar · SG15-10, Rubber seal ↗

    Exact description Rubber seal with the same nominal body, wider inner ring, rail-size and mass entries. No unique closure suffix, load rating or limiting speed stated here.

  3. Runstar · SG15, Rubber seal ↗

    d 5/D 17/B 8/B1 9.75 mm; suitable rail 6 mm and mass 8 g. Same three body numbers do not establish the SG15-10 rail interface.

  4. Motion · its own SG15-10 row and section ↗

    Separate manufacturer: dw 10/d 5/D 17/C 8/B 5.75 mm. Actual section identifies the outer-ring C and inner-ring B spans; used to distinguish manufacturer geometry, not to specify Runstar load, material or groove angle.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.