Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Track rollers
SG25
SG25 is a track rollers designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 8 × 30 × 14 mm. The publishing works are in Fujian province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Will changing an SG20 carriage to SG25 solve the problem?
The published dimensions establish a redesign, not a capacity upgrade: Runstar SG25 uses an 8 mm mounting bore and a 10 mm guide-size field. If the aim is a heavier carriage, first separate the dimensional changes from the missing load evidence.
Four interfaces change before any capacity claim can be considered.
Runstar SG25 [1] is labelled shields and lists d/D/B = 8/30/14 mm, B1 = 15.5 mm and 49 g. The SG20 comparison item [2] is labelled Rubber seal and lists 6/24/11 mm, B1 = 12.75 mm and a different guide-size field. This is a dimensional comparison of named constructions, not a seal-equivalence claim.
Change from SG20
SG25 field
Drawing work needed
Mounting bore: 6 → 8 mm
d 8 mm
Re-specify the axle and its fit/support; an unchanged 6 mm axle is not the nominal new interface.
Outer diameter: 24 → 30 mm
D 30 mm
Check wheel centre, neighbouring brackets and the moving envelope.
Body/inner ring: 11/12.75 → 14/15.5 mm
B 14; B1 15.5 mm
Rework support faces and spacer stack using the axial-profile drawing.
Guide field: 8 → 10 mm
10 mm
Identify the mating rail and contact contour; retaining the old rail needs explicit qualification.
The outer-radius increase is 3 mm by arithmetic. It is not an automatic 3 mm change in carriage height, because installed height depends on the groove/rail contact and axle position. Resolve that geometry on the assembly drawing.
A larger wheel cannot answer the missing load question.
The examined SG25 page publishes no allowable load, contact-contour tolerance or preload setting. Its 49 g mass and 30 mm diameter cannot fill those gaps. Do not assign another brand’s SG25 or an INA rating to this Runstar item.
If more payload is the reason for the change, send the current and proposed wheel-position drawings with payload location and rail support positions. Ask for selection evidence for this SG25/rail combination. A response that simply divides payload by wheel count leaves load distribution and moment effects unanswered.
The proposal needs two separate approvals: the revised axle/spacer/rail geometry, and the permissible duty of the proposed roller and rail. Schaeffler’s system-design guidance [3] supports considering the supporting geometry and rigidity; its values are not SG25 limits.
If the aim is only to replace a worn SG25, there is no SG20-to-SG25 conversion to justify. Use the SG25 axial-profile drawing to preserve B1 support and shields clearance, and identify the existing rail profile. A match on 8/30/14 establishes an envelope, not those contact details.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
11 mm
Mean diameter dm
(D + d) / 2
19 mm
Arithmetic on the figures above — not a bearing life calculation for your load case.
Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.
Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs
223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Request a quote for SG25.
Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.
Printed page 21: adjacent construction and displacement-force factors. General system context, not Runstar load, preload, material or lubrication limits.
Guide checked 2026-10-08. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies