BearingIndex
THE BEARINGINDEX DIRECTORY

SR144TLW — 3.175 × 6.35 × 2.78 (unit unconfirmed)

HISTORICAL DIMENSION INTERPRETATIONUNIT UNCONFIRMED

Runstar’s exact SR144TLW detail states open construction and stainless steel balls, with d 3.175, D 6.35 and B 2.78. The examined dimension labels do not state their unit. The directory’s historical mm interpretation is retained as unconfirmed; the product photographs are not a dimensioned manufacturing drawing.

Ball bearings

SR144TLW

SR144TLW is a ball bearings designation documented on BearingIndex from 1 manufacturer publication. The historical directory dimension interpretation is 3.175 × 6.35 × 2.78 (unit unconfirmed). The examined source does not state its dimension unit. The publishing works are in Fujian province, China. The historical record is retained; the individually reviewed guide identifies the unresolved source fields.

Bore d
3.175 unit unconfirmed
Outside D
6.35 unit unconfirmed
Width B
2.78 unit unconfirmed

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Keep the SR144TLW construction attached to the quote, not just its three numbers.

Runstar’s exact SR144TLW entry identifies an open bearing with stainless steel balls. SR144TLWN uses the same listed dimension numbers but is described with ceramic balls. The supplier’s SR144TLW marketplace listing also writes width 2.779 in its title/specification and 2.78 in its own catalogue table. Resolve both the construction and the dimensional wording before accepting an offer.

Open steel balls, ceramic balls and a shield are different offers.

The exact official SR144TLW detail [1] labels its construction 开式 (open) and its memo 不锈钢球 (stainless steel balls). SR144TLWN [2] is also open but its memo says 陶瓷球 (ceramic balls). Both display d 3.175, D 6.35 and B 2.78 without a dimension unit. Matching those fields does not make the material change disappear.

Complete Runstar designationExamined construction statementWhat changes from the TLW request
SR144TLW [1]Open; stainless steel ballsKeep this exact identity on the drawing and quotation.
SR144TLWN [2]Open; ceramic ballsA different ball-material statement despite identical listed dimension numbers.
SR144TLZW [4]Single shield; steel ballsA shielded configuration, rather than the requested open TLW.
SR144K1TLW [4]Open; steel balls, separable inner ringThe catalogue adds a separable-ring construction. Do not remove K1 from the offer identity.

The latter two statements come from Runstar’s own supplier listing catalogue [4]; they are configuration descriptions, not independent interchange approvals. Ask the supplier to identify any departure from SR144TLW explicitly. Do not order a generic “SR144 dental bearing” and let its matching size field decide which construction arrives.

The stainless-steel-ball memo does not specify a steel grade, and the ceramic-ball memo does not establish a ceramic composition or the material of every ring. The examined photos show several bearing views; they do not verify the quoted lot’s ball or cage material. Request the selected construction’s material specification together with its complete designation.

Ask for one drawing that resolves 2.78 versus 2.779.

SR144TLW source locationWidth wordingEvidence boundary
Official exact detail [1] and list [3]B 2.78The examined d/D/B labels do not print a unit.
Supplier listing title and Specification [4]3.175 × 6.35 × 2.779No dimension unit or explanation of the extra digit in the examined field.
Same supplier listing, catalogue row [4]3.175 × 6.35 × 2.78SIZE(dxDxB) supplies neither a tolerance nor a stated unit.

Keep the two source locations with the enquiry and ask Runstar which dimensional specification its SR144TLW quotation uses. The extra digit is not itself a manufacturing tolerance, a measured sample result or proof that one source rounds the other. This page retains the historical mm interpretation as unconfirmed; it does not compute an installation allowance from these bare numbers.

Request a revision-controlled drawing that names the dimension unit, identifies the surfaces defining B and states the tolerances for the offered open steel-ball construction. Attach the original assembly or rotor identification and its axial locating surfaces. A catalogue number and a product photo do not establish compatibility with a particular handpiece or permission to change its bearing arrangement.

Keep the marketplace claims separate from the offered specification. The supplier attributes say ABEC-7 and “Rpm50000-500000”. That broad speed wording is a seller statement, not a configuration-specific test record or an approved operating point. Ask the supplier to identify the selected bearing, lubrication, assembly and conditions behind any speed or precision evidence it provides.

The official list leaves the exact TLW torque, mass, ball size and ball count as dashes. They are unprovided fields in that list, not zero values. If torque matters to acceptance, obtain the proposed TLW construction’s test method and conditions; do not substitute a value from a different suffix or treat the marketplace’s speed range as torque evidence.

A quote ready for comparison should therefore identify SR144TLW / open / stainless-steel balls, resolve the width wording and dimension unit in one controlled drawing, and attach any required performance evidence to that same construction. Commercial or category claims about dental use do not answer these configuration questions.

What each manufacturer published.

ManufacturerBore d — source number (unit unconfirmed)Outside diameter D — source number (unit unconfirmed)Width B — source number (unit unconfirmed)Source recorded
Runstar
SR144TLW
3.175
Historical directory interpretation: 3.175 mm. The exact SR144TLW detail and list omit the dimension unit; obtain the offered drawing.
6.35
Historical directory interpretation: 6.35 mm. Source unit not explicitly confirmed in the examined exact entry.
2.78
Historical directory interpretation: 2.78 mm. Official entry and supplier catalogue say 2.78; the supplier listing title/specification says 2.779, without an explained tolerance or explicit unit.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish SR144TLW.

Runstar

Zhangzhou, Fujian, China

Miniature ball and thrust bearings

Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.

Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs

223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Runstar about SR144TLW

Applications the publishing works state.

ApplicationStated by
Fishing tackleRunstar
Medical equipmentRunstar
Precision instrumentsRunstar
Small motorsRunstar

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Request a quote for SR144TLW.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Runstar · SR144TLW source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Runstar · exact SR144TLW detail ↗

    Open and stainless-steel-ball memo; d 3.175/D 6.35/B 2.78 with dimension units unstated. Photos do not establish a quoted configuration or controlled drawing.

  2. Runstar · exact SR144TLWN detail ↗

    Same dimension numbers and open type, but ceramic-ball memo. No material composition or interchange approval established.

  3. Runstar · dental list, page2 ↗

    Exact TLW row and headers: dimension units unstated; torque/mass/ball fields show dashes. These are missing values, not zero or proof of no other published information.

  4. Runstar supplier listing · SR144TLW on Made-in-China ↗

    Supplier-owned listing, not independent product testing: title/specification2.779 versus catalogue2.78, construction rows and ABEC7/broad-speed attributes. No confirmed dimensional tolerance, clinical suitability or lot verification inferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.