BearingIndex
THE BEARINGINDEX DIRECTORY

U3-13M — 3 × 13 × 6 mm

BOUNDARY DIMENSIONSUNIT / mm

Hongchi lists U3-13M bore 3 mm, outside diameter 13 mm, width 6 mm and groove width 3.5 mm. These dimensions do not specify the groove radius, depth or a compatible rail profile. The page’s shared section illustration is not a dimensionally matched U3-13M drawing.

Non-standard

U3-13M

U3-13M is a non-standard designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 3 × 13 × 6 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
3 mm
Outside D
13 mm
Width B
6 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 3.5 mm groove-width entry does not identify the rail that U3-13M can run on.

Hongchi’s non-standard U-series page gives U3-13M dimensions of 3×13×6 mm and groove width 3.5 mm. Its linked illustration combines different profiles and includes dimensions that do not match that envelope. Before replacing a guide roller, obtain the selected groove drawing and mating-rail section. The neighbouring U4-15M also lists width 6 mm and groove width 3.5 mm, but changes the bore, outside diameter, loads and speeds.

Keep the 3.5 mm table entry separate from the shared section illustration.

Hongchi’s U3-13M parameter table [1] explicitly labels bore, outside diameter, width and groove width in millimetres. It does not attach a groove radius or depth to that row. The illustration linked from the same page [2] needs a separate identity check.

EvidenceWhat is visibleWhat it settles
U3-13M tableBore 3 mm; outside diameter 13 mm; width 6 mm; groove width 3.5 mm.The published model-row dimensions, without a complete groove profile.
Left section illustrationAn angled groove with a 90° annotation.A depicted profile, without evidence that U3-13M has that angle.
Right section illustrationA curved groove; dimensions marked 6.93 across the width and 16.54 at the outside.These numerals do not match the U3-13M table’s width 6 and outside diameter 13. Do not transfer this section’s geometry to the model.

The same illustration URL appears on the adjacent U4-15M page [3]. It contains no visible U3-13M designation establishing a selected, controlled drawing. Enlarging the image does not create a model identity or make its small tolerance annotations reliable. Request a current drawing carrying the complete offered designation and revision; neither pictured profile is a basis for releasing the U3-13M mating part.

In particular, groove width 3.5 mm is not a stated groove radius of 1.75 mm, permission to use a 3.5 mm round rail, or a groove-depth dimension. A buyer choosing a roller for an existing rail needs the rail section and the bearing’s actual groove section together. Mark the intended contact region, nearby clearances and mounting orientation so the manufacturer can evaluate that interface.

The product photograph shows five bearings without a readable U3-13M marking or dimensional scale. It cannot close the drawing gap. Ask for the actual offered part’s profile and dimensions rather than judging fit from the photograph’s apparent shape.

The page’s footer identifies Ningbo Hongchi Bearing, while its table footnote directs selection questions to “宏诚精密”. The examined page does not explain that name difference. Confirm who issues the drawing and quotation; do not infer a corporate relationship from the footnote.

The neighbouring roller keeps two dimensions but changes the shaft and ratings.

Hongchi links U4-15M [3] as the next item. Comparing its actual row with U3-13M [1] shows why the shared groove-width number is insufficient for substitution.

Published fieldU3-13MU4-15M
Bore / outside / width3 / 13 / 6 mm4 / 15 / 6 mm
Groove width3.5 mm3.5 mm
Dynamic Cr / static Cor1300 / 488 N957 / 350 N
Grease speed entry40 × 1000 rpm48 × 1000 rpm
“润滑剂” speed entry48 × 1000 rpm56 × 1000 rpm

U4-15M does not retain the 3 mm shaft bore or 13 mm outside envelope. Its larger outside diameter also does not make its published load ratings higher: the table gives lower dynamic and static figures than U3-13M. This is a comparison of manufacturer entries, not a tested ranking or a replacement approval. Keep the requested U3-13M designation and assess any U4 proposal against both the shaft and rail interfaces.

U3-13M’s dynamic 1300 N and static 488 N are separate bearing ratings; do not add them to claim a 1788 N working load. The page gives no equivalent allowable rail-contact load. Have the manufacturer assess the actual load direction, contact geometry and rail material alongside the bearing’s internal duty. Passing the 3 mm shaft check does not establish the external rolling contact.

The U3 row’s grease entry corresponds to 40,000 rpm. Its other entry corresponds to 48,000 rpm but is labelled “润滑剂” — lubricant — rather than explicitly identifying an oil and operating condition. For a 45,000 rpm requirement, the first published entry is below the requirement and the second does not by itself approve a suitable lubrication configuration. Ask Hongchi to select and assess the actual arrangement; do not silently relabel that column as oil.

The same page lists grease filling 25–30%, LY-series grease and a temperature entry of −50 to 150°C. It does not define the percentage’s reference volume or document simultaneous operation at 45,000 rpm and 150°C. Record the required temperature and speed together, and obtain the selected grease, filling basis and resulting duty confirmation.

Clearance is listed as 0.005–0.013 mm without a stated direction or measurement condition. It is not a guaranteed groove-tracking accuracy. The material table names GCr15 for rings and balls, with SPCC/SUS shield and SUS/MN cage entries; those alternatives do not prove that the entire unit is stainless steel. Confirm the delivered configuration and clearance definition rather than expanding the M suffix into an unsupported material claim. The page’s cited standard names also do not supply an identifiable test report for this model.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Source recorded
Hongchi
U3-13M
Hongchi’s U-series table additionally lists groove width 3.5 mm. The linked mixed-profile illustration does not establish this model’s controlled groove geometry.
31362026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish U3-13M.

Hongchi

Ningbo, Zhejiang, China

Miniature metric, inch and thrust bearings

Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.

Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings

80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Hongchi about U3-13M

Applications the publishing works state.

ApplicationStated by
Cooling fansHongchi
DronesHongchi
Miniature motorsHongchi
Precision instrumentsHongchi

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for U3-13M.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Hongchi · U3-13M source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Hongchi · exact U3-13M non-standard roller publication ↗

    Explicit 3/13/6 mm envelope and 3.5 mm groove-width entry; Cr 1300/Cor 488 N, grease 40 and lubricant 48 ×1000 rpm, clearance 0.005–0.013 mm and configuration entries. The table footnote describes selection data as reference information.

  2. Hongchi · shared angled and curved section illustration ↗

    Different illustrated profiles, without a visible U3-13M model identity. Right-section 6.93/16.54 numerals do not match the exact table envelope; do not use the image as this model’s controlled groove drawing.

  3. Hongchi · adjacent U4-15M publication ↗

    Distinct 4/15/6 mm model, groove width 3.5 mm, dynamic/static 957/350 N and grease/lubricant speed entries 48/56 ×1000 rpm. It links the same section illustration and does not establish interchangeability with U3-13M.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.