BearingIndex
THE BEARINGINDEX DIRECTORY

V6/16M — 6 × 16 × 7 mm

BOUNDARY DIMENSIONSUNIT / mm

Hongchi’s V6/16M table gives bore 6 mm, outside diameter 16 mm, total width 7 mm and a separate groove-width entry of 5 mm. The linked photograph shows a group of bearings; it is not a dimensioned V6/16M groove section. Obtain the selected roller profile for the actual track.

Non-standard

V6/16M

V6/16M is a non-standard designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 6 × 16 × 7 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
6 mm
Outside D
16 mm
Width B
7 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

A 6×16×7 mm match does not define the V6/16M track contact.

Hongchi adds groove width 5 mm to the V6/16M’s 6/16/7 mm dimensions. Its second table gives clearance 0.005–0.013 mm and several speed, grease and temperature entries, with an explicit reference-only footnote. These figures do not supply a complete track profile or a tested operating envelope. Start with the roller-to-track drawing, then tie the offered construction and operating conditions to the actual part.

The 5 mm groove, 7 mm total width and clearance entry describe different questions.

Hongchi’s exact V6/16M table [1] places width 7 mm and groove width 5 mm in separate rows. A three-number bearing search drops the fourth interface. Keep that groove entry visible when comparing a proposed guide wheel with the retained track.

V6/16M source field [1]Published figureWhat the figure does not supply
Bore / outside diameter6 / 16 mmThe groove’s contact geometry or effective rolling radius.
Total width / groove width7 / 5 mmGroove angle, depth, root radius, axial position and profile tolerances.
Clearance minimum / maximum0.005 / 0.013 mmThe measured direction, inspection conditions or installed wheel-to-track play.

The V designation and 5 mm width do not establish a 90° groove or compatibility with a standard rail. The linked photograph shows several different bearings without an exact V6/16M dimensioned section. It cannot fill the missing groove angle or identify which pictured part represents this offer.

Send a cross-section of the actual track and mark the intended contact locations alongside the proposed wheel section. Have the supplier return groove angle/depth/root radius, profile position and tolerances on the controlled drawing. Compare the full contact profile before accepting another 6×16×7 mm bearing. The width difference 7−5 is not a machining allowance or a permitted track modification.

The clearance range converts to 5–13 μm, but the page does not label it as an installed guide-play limit. Do not use it to set track spacing or preload, or promise positioning accuracy. Agree its measurement definition separately from the assembled wheel/track acceptance, which must include the actual mounting and contact arrangement.

Reference figures and standard numbers do not form one tested operating envelope.

The same page marks its data as reference-only. Its speed rows sit under a ×1000 rpm heading: grease 40 and a second row labelled 润滑剂, meaning lubricant, 45. That second label does not specifically identify oil. Keep the source wording while requesting the applicable lubrication method and conditions.

Exact source entry [1]Reading of the publicationRequired part-specific evidence
Speed rowsGrease 40×1000 rpm; “lubricant” 45×1000 rpm.Selected lubricant, load, temperature and acceptance conditions. Neither row supplies track travel speed without the actual rolling contact radius.
Grease entry / grease rateLY series / 25–30%.Exact grease and the percentage’s reference volume/inspection method; the entry is not a replenishment interval.
Temperature entry−50 to 150°C.The selected assembly’s applicable conditions and test record. The range does not establish operation at 40,000 rpm and 150°C together.
Basic dynamic / static ratingCr 1082 N / Cor 442 N.Rating definitions and application assessment; these are not a tested track-contact load limit.

The material rows name Gcr15 for rings and balls, SPCC/SUS for shields and SUS/MN for the cage. Retain them as supplier statements and resolve the slash-separated alternatives for the actual offer. A list of possible materials does not identify the delivered batch.

There is a concrete evidence problem in the adjacent inspection-standard column. It cites “GB-T 305-1998” beside several material entries. The official GB/T 305-1998 record [2] concerns external-ring snap-ring grooves and rings, and lists the edition as withdrawn from 1 May 2020, replaced by GB/T 305-2019. That reference does not verify Gcr15 composition or define this wheel’s rolling-track groove. Ask for the applicable material evidence and the selected profile’s drawing separately.

The grease/temperature rows cite “JB-T 8571-1997”. Its official record [3] describes sealed deep-groove bearing dust, grease-leakage and temperature-rise testing and marks that edition as withdrawn. The standard reference is not a V6/16M test report or a demonstrated −50 to 150°C operating result. Agree the applicable methods and obtain the part/configuration-linked results before relying on the range.

The page is branded Hongchi, while its selection footnote names 宏诚精密. Confirm which entity supplies the part and signs its drawing and technical response. These unresolved references do not prove the bearing is defective; they identify the documents needed to evaluate this particular wheel and its proposed duty.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Source recorded
Hongchi
V6/16M
61672026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish V6/16M.

Hongchi

Ningbo, Zhejiang, China

Miniature metric, inch and thrust bearings

Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.

Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings

80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Hongchi about V6/16M

Applications the publishing works state.

ApplicationStated by
Cooling fansHongchi
DronesHongchi
Miniature motorsHongchi
Precision instrumentsHongchi

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for V6/16M.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Hongchi · V6/16M source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Hongchi · exact V6/16M dimensional and operating tables ↗

    6/16/7 mm plus groove width 5 mm; clearance 0.005–0.013 mm; material alternatives, LY grease, 25–30% grease rate, temperature −50 to 150°C, Cr1082/Cor442N and separate grease/lubricant speed rows under ×1000 rpm. Reference-only footnote; group photograph does not define the exact groove.

  2. SAMR · GB/T 305-1998 scope and status ↗

    External-ring snap-ring groove/ring dimensions and tolerances; withdrawn 2020-05-01 and replaced by GB/T305-2019. Its scope/status do not certify the supplied V6/16M material or wheel-track geometry.

  3. SAMR · JB/T 8571-1997 scope and status ↗

    Withdrawn edition of a sealed deep-groove bearing dust, grease-leakage and temperature-rise test procedure. A supplier’s citation is separate from the selected V6/16M test conditions and results.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.