F&D / CBB
Fuda / F&D / CBB: a sourcing guide organised around the manufacturer’s bearing-design request and production evidence.
Give the engineering team the conditions, not just the size.
Fuda identifies F&D and CBB as its bearing brands and describes applications including industrial motors, household appliances and automotive equipment. Company profile [1] Its most useful sourcing resource is the bearing-design form: it asks about lubrication, temperatures, load, fits, running requirements and previous failures. Design request [2]
Follow the questions Fuda actually asks.
The official form groups the request into working information, performance, bearing fit, customer requirements, history and assembly dimensions. It also offers synchronous and reverse-design options. [2] Our suggested preparation follows those groups so an engineer can identify missing conditions early.
Environment and lubrication
Record whether the bearing faces water, dirt, abrasive material, chemicals or electrical-conductivity concerns. Give bearing, shaft, housing and ambient temperatures separately where measured. Identify grease code or the intended oil-delivery arrangement. These are different inputs from “indoor use”.
Motion, load and location
Describe shaft orientation, which ring rotates, whether the position locates the shaft, load directions and any impacts. State the operating-speed range and duty cycle. If data is unknown, mark it unknown and ask how to obtain it; do not enter nominal values merely to complete a form.
Fits and running targets
Provide shaft/housing materials, relevant dimensions and tolerances, and whether the shaft is hollow or the housing thin-walled. Discuss clearance, running accuracy, noise, friction torque and stiffness as a connected specification, rather than picking dropdown classes without the assembly context.
The form’s options are inputs to an engineering discussion. They do not show that every product is stocked in every clearance, precision or noise class. This guide has not submitted the manufacturer’s form or obtained an engineering approval.
A failed bearing is a different request from a new design.
Fuda’s form explicitly requests the previously used bearing and supplier, failure mode, cage and seal information, equipment cycle and service history. [2] That is especially useful when a motor or appliance has noise or life problems after a seemingly dimensionally correct replacement.
Capture what was installed
Photograph the markings and mounting position. Record the full suffix, closure, grease information and available drawing revision. Note what changed between the successful and failed configurations.
Describe the symptom and timing
Separate observed symptoms from a suspected cause. State hours/cycles, loading, temperature, lubrication and installation history. Keep the failed part available for an agreed examination.
Approve the proposed change deliberately
Ask which specification changes Fuda proposes, why, and how the sample will be tested. Confirm the allowable assembly changes and the evidence required before switching serial production.
Trace the material and process claims to your order.
The technology-centre page describes dimensional, mechanical, life and material laboratories; its production presentation includes turning, heat treatment, grinding, assembly, greasing, final inspection and packing. It also discusses bearing-steel-pipe manufacture. [3] Those are manufacturer-published activities, not a batch report reviewed by BearingIndex.
For finished bearings
Ask for the material specification, controlled drawing and critical-property inspection plan. For a noise-sensitive order, define the measurement conditions and acceptance limit, and ask whether the report covers individual bearings or an assembly test.
Do the published quality-system names qualify the order?
The corporate page states certification claims, but this review has not validated current certificate numbers, expiry dates or plant scopes. Request and verify the certificate applicable to the proposed entity/site, then agree the product-level acceptance separately.
The name on the box and the name on the contract may differ.
The official subsidiary page names Cixi Zhongzhou Bearing and Cixi Unite Machinery and gives Pengqiao Industrial Zone, Henghe, Cixi as the manufacturing-base address. [4] A CCCME supplier profile uses Fuda Bearing Corporation Co., Ltd., lists F&D/CBB and gives the same industrial-park context. [5]
Use those records to start an identity check. Ask which legal entity manufactures the selected variant, issues the quotation and provides the inspection records. The chamber profile contains supplier descriptive material; it does not independently establish current production capacity or product approval.
The official company introduction explicitly ties its scale figures to 2021. [1] Do not use them as today’s available capacity or as a promise of short delivery. Ask for the quantity and delivery window of your actual request.
What should a usable quotation include?
The complete bearing designation and agreed drawing, closure/grease/clearance, inspection deliverables, sample terms, quantity, delivery destination, promised date and contracting company. A brand and series alone leave too many conditions open.
Prepare a Fuda engineering request.
Tick what you have ready. Copy the full checklist with its current status for your procurement notes.
Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.
Documented models.
0 model recordsNo documented models yet.
Try broader requirements, or explore the manufacturer’s published product scope.
Explore manufacturers →Evidence, with boundaries.
Our review approach →Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.
- Manufacturer publicationFuda · company profile ↗
Brand/application identity and explicitly 2021 scale statements; not current capacity or verified certificates.
- Manufacturer engineering formFuda · bearing-design request ↗
Actual requested technical inputs. Form options do not establish available variants or engineering acceptance.
- Manufacturer publicationFuda · technology centre and laboratory ↗
Published laboratory, material and process activities; no order report or factory audit reviewed.
- Manufacturer publicationFuda · subsidiaries and manufacturing bases ↗
Named subsidiaries and industrial-park address; exact contracting and production entity needs confirmation.
- Chamber-hosted supplier profileCCCME · Fuda Bearing Corporation profile ↗
Brand and address context; company-supplied descriptions are not independent verification of capacity or quality.
Report a source correction → · Return to inquiry checklist ↑
No reviewed model or batch reports are available. Independent verification is not implied.