Hengyi
Haian Hengyi advertises copper-alloy bushes and sliding plates, solid-lubricant inlaid versions and steel-backed copper composites. Its HYB60, HYB60S, HYB61S, HYB63 and HYB63S pages describe materially different constructions. Qualify the actual alloy, lubricant, mating surface and installed duty; a lubricant temperature or independent catalogue limit is not a complete assembly rating.
Choose the sliding construction before quoting the bush or wear plate.
Haian Hengyi Sliding Bearings Co., Ltd. (海安县恒益滑动轴承有限公司) states that it was established in September 1996 in Haian, Nantong. Its published offer spans machined copper-alloy parts, solid-lubricant inlaid parts and steel-backed copper-alloy composites. These routes need different drawings and acceptance records. Start with the sliding pair and actual lubrication access, rather than treating every HYB product as the same maintenance-free material. Official history and offer [1]
A copper bush, an inlaid plate and a bonded composite are different purchases.
| Published family | Actual described construction | What the enquiry must resolve |
|---|---|---|
| HYB60 | Finished copper-alloy bearing; the page lists several alloy grades and bush, shell and washer forms. | Exact alloy and form, shaft/housing interfaces and the required oil/grease arrangement; copper alloy alone does not establish dry-running suitability. |
| HYB60S and HYB61S | Solid lubricant embedded in copper alloy; HYB60S includes bush/washer forms while HYB61S is a sliding-plate offer. | Base alloy, lubricant identity and pattern, contact area, mating surface and permissible operating/maintenance conditions. |
| HYB63 | Low-carbon steel backing with a rolled tin-bronze layer described as over 2 mm, compounded through a special process. | Steel and bronze grades, finished layer thickness, bonding integrity, fixing method and lubrication arrangement. |
| HYB63S | Steel-backed copper-alloy sliding plate with embedded solid lubricant; marketed for high-load/low-speed duty with limited lubrication access. | Both bonded-layer acceptance and the lubricant/mating-surface duty limits; the S version is not automatically interchangeable with HYB63. |
These are manufacturer descriptions, not independently measured sample properties. HYB60 original [2] HYB60S original [3] HYB61S original [4] HYB63 original [5] HYB63S original [6]
The HYB61S page advertises workpiece length below 4,000 mm, while HYB63 and HYB63S state length below 6,000 mm, width below 1,200 mm and thickness 10–300 mm. These are published processing envelopes, not confirmation that every combination can be supplied now. Send the complete drawing, mass, quantity and handling requirements for a part-specific feasibility response.
Keep the website’s code and unit ambiguities out of the purchase order.
HYB60 and HYB60S distinguish alloys such as CuSn12, CuSn10Pb10 and CuAl10Ni5Fe5. They are not interchangeable merely because they share a family prefix. The published strength-table headings use N/m²; the table does not supply a sufficiently clear approved material specification. Obtain the exact material standard, grade, units, test method and heat/lot certificate. Do not silently reinterpret the website values as MPa. Actual HYB60 alloy table [2] Actual HYB60S alloy table [3]
The HYB60S bush table was also read and visually checked in the browser. It labels the bore and outside diameter ID F7 and OD m6, then gives part numbers against lengths. For the 12 mm bore / 18 mm outside-diameter row, the 10 mm length cell reads 21810 while nearby cells include 121812 and 121815. The 25 mm bore / 33 mm outside-diameter row has 331520 under the 15 mm length column. These are actual published ambiguities, not corrected order codes. Ask for the current controlled drawing and full designation rather than reconstructing missing digits. Actual dimensional table and viewed row alignment [3]
For a cylindrical or flanged bush
Specify bore, outside diameter, length, flange dimensions and required tolerances; provide shaft/housing drawings, installed clearance, retention and lubricant placement. Agree whether inspection is before or after installation and how the complete assembly is accepted.
For a plate or thrust washer
Specify working face, thickness, flatness, fixing-hole/countersink layout, backing support and contact movement. Identify allowable wear and the method of replacement. For a composite, distinguish total thickness from the finished bronze layer.
A lubricant temperature and three independent limits do not define one approved duty.
The HYB60S/HYB61S lubricant table associates graphite-based HYB-301 with a 400 °C temperature limit and HYB-302 with a 300 °C limit and water-lubrication wording. Those are the page’s lubricant-table statements, not verified continuous operating temperatures for the full bush, mating shaft, fit and lubricant combination. Confirm the exact lubricant formulation and environment before using either value. “Maintenance unnecessary” also needs part-specific written conditions. Original lubricant wording [3] Sliding-plate lubricant wording [4]
HYB63 and HYB63S publish a bronze-surface table: CuSn6.5P0.1 has a listed moving-load limit of 250 N/mm², while CuSn6Zn6Pb3 and CuSn8P0.3 have 150 N/mm²; each row separately lists surface temperature below 300 °C and maximum sliding speed 1.5 m/s. These are manufacturer reference entries. Do not assume the listed maximum pressure, speed and temperature are permitted simultaneously. No complete approved combined-duty or PV envelope was established from these pages. HYB63 original limit table [5] HYB63S original limit table [6]
- Describe contact and movement. Provide actual loads/contact area, continuous sliding or oscillation, stroke, starts/stops and shock. Ask the supplier to document pressure and speed assumptions for the proposed geometry.
- Identify the mating surface. State material, hardness, finish, alignment and support. Request the proposed requirements and allowable deviations for the complete sliding pair.
- Describe lubrication and environment. Identify initial lubrication, replenishment access, dry/wet service, temperature cycle and abrasive/corrosive contamination. Agree the actual running-in and maintenance procedure.
- Validate the candidate pair. Agree representative duty, wear/friction/temperature acceptance and inspection intervals. A general material table cannot replace a drawing-linked application trial.
Separate material release, composite-layer acceptance and company qualifications.
For a copper-alloy part, request alloy/heat traceability, agreed material tests and dimensional results. For an inlaid part, add lubricant identity, placement and working-face inspection. For HYB63/HYB63S, ask how the bonded interface and remaining bronze thickness are inspected, with acceptance methods/results tied to the lot. The product pages’ cost-reduction and patent-number wording is not a price commitment, present patent-status verification or delivered-layer test report. Composite construction and claims [5] Inlaid-composite claims [6]
The original honour image was loaded and enlarged in the browser. It names 海安县恒益滑动轴承有限公司, identifies high-tech enterprise certificate GR202132008270, and states 30 November 2021 with three-year validity. That image establishes a historical company-level certificate, not current renewal status or a bearing test certification. Obtain present originals and issuer evidence for the current entity/site/scope. Generic ISO/CE wording and customer names in the company description were not independently verified as current certificates or customer approvals. Actual enlarged historical certificate [7] Company-description scope and unverified claims [1]
The official contact page publishes 68 Kai Yuan Avenue, Haian Industrial Area, +86 513 88690066, and [email protected] / [email protected]. The email domain differs from hazc.com; the page alone does not establish the contractual role of those contacts. Confirm the legal seller, manufacturing/inspection site, responsible engineering owner and receiving address before sending drawings or arranging samples. No enquiry was sent. Actual official contact [8]
Prepare a Hengyi sliding-pair and construction brief
Tick what you have ready. Copy the full checklist with its current status for your procurement notes.
Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.
Documented models.
20 model recordsEvidence, with boundaries.
Our review approach →Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.
- Actual official publicationHengyi · company introduction ↗
1996 history and stated range; client names, capacity and generic ISO/CE wording remain manufacturer claims.
- Actual official product and material tableHengyi · HYB60 copper-alloy bearing ↗
Different alloy/form routes; strength-unit headings not silently converted into approved values.
- Actual official tables and browser dimensional-table image checkedHengyi · HYB60S inlaid bearing ↗
Construction, lubricant wording and ambiguous order codes; no universal maintenance/temperature approval.
- Actual official productHengyi · HYB61S inlaid sliding plate ↗
Plate form and processing-length statement; operating conditions must be approved for the actual pair.
- Actual official construction and limit tableHengyi · HYB63 steel-backed copper-alloy plate ↗
Steel backing, rolled bronze layer and separate limits; cost/patent claims not independently verified.
- Actual official construction and limit tableHengyi · HYB63S inlaid composite plate ↗
Embedded lubricant plus composite; separate table maxima are not a combined-duty guarantee.
- Original manufacturer image loaded, enlarged and visually read in browserHengyi · original historical high-tech certificate image ↗
Exact entity, GR202132008270, 30 November 2021, three-year period; no current status inferred.
- Actual official publicationHengyi · dedicated contact ↗
Kai Yuan Avenue, 88690066 and dftrd.com email routes; contractual role/current responsibility requires confirmation.
Report a source correction → · Return to inquiry checklist ↑
Hengyi published product scope reviewed
The manufacturer website describes self-lubricating sliding bearings and wear plates.
Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.
Company-level record; not a model test report · 2026-09-24 04:20:33
Source documentation retained for editorial review.