Hongchi
Ningbo Hongchi: miniature metric/inch and flanged bearing enquiries, plus thin-section bearings and nonstandard grooved wheels.
For a miniature assembly, the flange and closure can change the fit.
Hongchi describes manufacture and sale of metric/inch miniature bearings, flanged bearings and plane thrust ball bearings with a stated 1–40 mm bore range. Its published FR188, 6800/63800 and U/V wheel pages provide useful starting dimensions for different enquiries. Confirm the offered variant and its complete drawing before treating a catalogue row as an approved assembly. Company scope [1] FR188 variants [2]
FR188 open and ZZ do not have the same axial envelope.
The official FR188 table uses mm, including for this inch-series reference. Both displayed variants have d = 6.350 mm, D = 12.700 mm and flange outside diameter 13.894 mm. Their bearing and flange widths differ. Original FR188 table [2]
| Displayed variant | Bearing width (mm) | Flange width (mm) | Assembly decision |
|---|---|---|---|
| FR188 open | 3.175 | 0.584 | Check shoulder seating, lubricant provision and exposed bearing protection. |
| FR188 ZZ | 4.762 | 1.143 | Recheck the axial stack and flange recess instead of approving by bore/OD alone. |
The page title also mentions RS/RZ, but the displayed width rows are OPEN and ZZ. Obtain separate dimensions, sealing structure and torque requirements for any RS/RZ quotation. Do not extend the ZZ dimensions to an unshown variant. Send the supplier a section drawing showing which ring is retained, the flange recess and allowable axial stack.
The same 10 × 19 interface can still require a different housing width.
6800
The published 6800 table gives d = 10 mm, D = 19 mm, and B = 6 mm for both OPEN and ZZ. Its lubricant entry names SRL. 6800 table [3]
63800
The 63800 table gives d = 10 mm, D = 19 mm, and B = 7 mm for both OPEN and ZZ. Its lubricant entry names the LY series. 63800 table [4]
Retain the extra digit in the designation: the 1 mm width difference matters to shoulders, spacers and retention. Ask for the actual closure, ring/ball materials, cage, internal clearance and lubricant identification on the offered BOM. The general material choices and grease temperature figures on these pages do not establish the complete bearing’s operating limits or prove that two variants have equivalent starting torque.
Specify the rail contact geometry, not just a groove width.
| Official wheel reference | d / D / B (mm) | Published groove width | Drawing still needed |
|---|---|---|---|
| U8-21M | 8 / 21 / 7 | 4 mm | Full groove radius/profile, contact position and rail section. |
| V10/22M | 10 / 22 / 8 | 6 mm | Included angle, groove/root profile and mating rail geometry. |
These dimensions come from the separate U and V product pages. Neither groove-width entry is a complete rail interface specification. U8-21M [5] V10/22M [6]
- Describe the track: send the rail cross-section, material/finish, alignment and usable travel, together with wheel axle/shoulder drawings.
- Define the working contact: give load directions, wheel spacing, speed, reversal frequency and expected contamination; agree contact geometry and adjustment.
- Approve the complete assembly: specify runout, rolling resistance and a trial under the actual rail load and travel. An internal bearing rating alone cannot approve the wheel/rail system.
Ask for Hongchi’s offered-part records before relying on generic technical text.
The company page lists roundness, roughness, length, microscope and vibration instruments. Request the measurement method, calibration status and acceptance report for your part and lot, particularly when low motor noise or starting torque is the purchasing reason. Published equipment statement [1]
Some published technical text names ZGSL or 双联, while the product-table consultation note names 宏诚精密. Their relationship to the offered Hongchi part is not established here. Treat those pages as technical reading rather than proof that Hongchi supplies every stated precision grade, uses those named instruments or performs the described incoming-material controls. Precision text [7] Noise text [8] Material text [9] Product consultation note [2]
Clarify the standard beside the material fields.
The product tables cite GB/T 305-1998 in their inspection-standard fields. The national standards platform identifies it as an outer-ring snap-ring groove/ring dimensions and tolerances standard, withdrawn on 1 May 2020. It is not evidence of steel chemistry, hardness or noise acceptance. Ask the supplier to identify the actual applicable material and geometry standards and provide part-linked test records. Primary standard record [10]
For a small motor or fan, agree mounted load, speed, fit, clearance, lubricant, warm-up and measurement conditions, then numerical noise/vibration and torque acceptance. The website’s application list, including medical equipment, does not establish qualification for a particular device.
Confirm who makes, quotes and warrants the selected variant.
The official company/contact pages identify 宁波宏驰轴承有限公司 and give 贵安路199号, 光明村, 庄市街道, 镇海区, Ningbo. The contact body and site header/footer publish different phone numbers; ask the responding supplier to confirm the current legal/manufacturing site and authorised order contact rather than inferring another factory from a telephone prefix. Official contact route [11]
The contact page links to a 1688 shop. That route reached a verification challenge during this review, so its current licence and manufacturing scope could not be checked. Obtain the business licence, contracting entity and production site directly and match them to the quotation and invoice. Official-linked marketplace route [12]
Hongchi states ISO9001 and environmental/RoHS credentials on its company page. Obtain current issuer, scope/site and validity documents, plus material-compliance evidence for the exact BOM where required. These website statements are not current certificate verification, and no stock, price or delivery promise is established by the reference tables. Company credential statements [1]
Prepare a Hongchi variant-and-interface enquiry
Tick what you have ready. Copy the full checklist with its current status for your procurement notes.
Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.
Documented models.
80 model recordsEvidence, with boundaries.
Our review approach →Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.
- Manufacturer publicationHongchi · company introduction ↗
Miniature scope, instrument list and credential self-statements; no current certificate or plant audit established.
- Manufacturer variant tableHongchi · FR188 ↗
Explicit mm OPEN/ZZ widths/flanges; no separate RS/RZ width specification; consultation note names another entity.
- Manufacturer reference tableHongchi · 6800zz ↗
10/19/6 mm and SRL entry; exact offered BOM/limits require confirmation.
- Manufacturer reference tableHongchi · 63800zz ↗
10/19/7 mm and LY entry; no whole-bearing temperature or equivalence validation.
- Manufacturer wheel tableHongchi · U8-21M ↗
8/21/7 mm, groove width 4 mm; complete rail-contact section not supplied by those fields.
- Manufacturer wheel tableHongchi · V10/22M ↗
10/22/8 mm, groove width 6 mm; angle/root and working load require drawing and qualification.
- Technical reading with unresolved attributionPublished technical text · bearing precision ↗
Names ZGSL; not accepted as proof of Hongchi part precision or audited process.
- Technical reading with unresolved attributionPublished technical text · vibration and noise ↗
Names ZGSL; named equipment and procedures not independently attributed to Hongchi.
- Technical reading with unresolved attributionPublished technical text · materials ↗
Names 双联; no inference of Hongchi supplier network or incoming controls.
- Primary standards authorityNational standards platform · GB/T 305-1998 ↗
Snap-ring groove/ring dimensions and tolerances; withdrawn 2020-05-01, not a material/noise certificate.
- Manufacturer contact publicationHongchi · contact page ↗
Legal name/address, body/header phone differences and official marketplace link; current contracting scope needs confirmation.
- Marketplace access limitedHongchi-linked 1688 shop · verification-limited ↗
Link read on official contact page; verification challenge prevented current business-licence/manufacturing review.
Report a source correction → · Return to inquiry checklist ↑
Hongchi published product scope reviewed
The manufacturer website describes miniature metric, inch and thrust bearings.
Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.
Company-level record; not a model test report · 2026-09-24 04:20:34
Source documentation retained for editorial review.