BearingIndex
THE BEARINGINDEX DIRECTORY

Jujian

Hebei Jujian (河北巨健) presents VOST insert/housed bearings alongside deep-groove and tapered-roller products. Its actual insert detail separates set-screw, tapered-bore and eccentric-collar routes, making mounting interfaces and locking a useful starting point. The company describes controlled assembly, traceability, automatic lubricant filling and pre-dispatch checking; agree the candidate drawing and lot evidence rather than relying on category photographs.

VOST INSERT AND HOUSED BEARINGS · LOCKING, MOUNTING AND LOT ACCEPTANCE

Order the complete mounting and locking arrangement, not just the bore size.

Hebei Jujian Bearing Manufacturing Co., Ltd. (河北巨健轴承制造有限公司) advertises VOST insert/housed bearings, deep-groove ball and tapered-roller bearings. The company describes a temperature-controlled assembly workshop and tracking from incoming materials to dispatch. Treat those as manufacturer statements and use the published product distinctions to prepare a complete, verifiable order. Official brand/home publication [1] Actual company process/traceability description [2]

Prepare a sourcing inquiry
01

Choose the insert, locking system and housing together.

The actual housed-bearing detail distinguishes UC200/UC300 and UB(SB)200 set-screw families, UK200/UK300 tapered-bore families, and UEL200/UEL300/SA200 eccentric-collar families. It separately lists pillow-block, square/diamond/round-flange, take-up, ring and suspended housings. These are published families, not a complete candidate dimensional or whole-unit load table. Actual insert/locking/housing description [3]

Buying decisionSupply in the enquiryCheck on the proposed unit
Bare insert or complete housed unitExisting bearing and housing designations, photographs and drawing; identify which components are being replaced.Insert outer seat/interface, housing material, retention and complete unit drawing/rating.
Shaft lockingShaft diameter with metric/inch units, tolerance/finish, rotation direction and start/stop or reversing duty.Actual set-screw, tapered-bore or eccentric method; supplied fastening/adaptor parts and supplier’s installation instructions.
Mounting footprintBolt pattern/slots, centre height, flange pilot, available space and take-up travel where applicable.Controlled dimensions, mounting orientation, fastening requirements and accessible lubrication point.
Alignment and loadShaft deflection/misalignment, radial/axial loads, speed, duty and support spacing.Allowed alignment and loading for the complete proposed unit; a spherical outer surface is not unlimited alignment compensation.

For a replacement, request written compatibility against your existing insert/housing combination. Preserve the complete suffix and installation method; do not substitute a differently locked unit merely because its bore matches.

02

Make the lubricant and contamination plan part of the order.

Jujian’s 16 January 2024 filling page says it uses an automatic injection machine to provide uniform filling. Its insert detail describes a double sealing structure. Neither establishes the quoted unit’s grease product, fill quantity/tolerance, seal material, relubrication interval or suitability for every dirty/wet environment. Request those details for the selected construction. Actual automatic-filling statement [4] Seal statement in housed-bearing detail [3]

New machinery

Provide dust/fibre exposure, water or wash chemicals, operating temperature, speed/load and duty. Agree seal/lubricant compatibility, fill control and an accessible maintenance route; specify any applicable cleanliness or hygienic requirement rather than inferring it from an application name.

Replacement in a failing position

Provide removed-part markings, contamination/wear observations and the current grease and replenishment practice. Ask the supplier to explain the proposed construction and inspection/test evidence before repeating the failed arrangement.

Agree the applicable storage, installation, startup and replenishment instructions. Claims of long life or low friction do not supply a candidate-specific maintenance schedule or field-life guarantee.

03

Use the other product families with their own configuration checks.

The actual deep-groove listing separates open, metal-shield and rubber-sealed constructions in its 62/63/64 entries, including a brass-cage 63 category. The 62 rubber-sealed detail provides general structure/application prose, but no controlled complete model table for clearance, accuracy, seal friction, grease or speed. Ask for the complete candidate designation and drawing rather than carrying generic high-speed wording into the quote. Actual deep-groove list [5] Actual 62 sealed detail [6]

The actual 302 tapered detail discusses cone/cup separation, opposing axial support and preload, but also uses broad interchangeability wording. Require the exact cone and cup identification, paired source, total assembled width, accuracy and setting procedure for your order. A general “interchangeable” statement should not approve mixing arbitrary parts or brands. If ordering components, agree their compatibility and who accepts the assembled result. Actual tapered detail and compatibility wording [7]

Aerospace, railway and automotive names in the company introduction are application marketing, not candidate-specific approval or a customer qualification record. For a regulated or safety-critical purchasing specification, request the actual required material/process, traceability, testing and approval documents. Scope of company application statements [2]

04

Connect the incoming material, assembly controls and dispatch result.

The company describes full-process traceability, and its 16 January 2024 inspection page says every bearing is checked before leaving. This does not identify which checks are performed on each item versus by sampling, or prove a life test on every bearing. Agree the actual dimensional, rotational, clearance/locking and seal/lubrication checks, methods, calibrated instruments and acceptance record for the lot. Traceability and assembly statement [2] Actual pre-dispatch-check statement [8]

A 25 January 2024 “company strength” image actually viewed shows steel tubes and a GCr15 incoming-product quality document. It is an incoming-material photograph, not Jujian’s ISO certificate or a finished-bearing test report for your lot. Request the applicable current material certificate and its link through manufacturing/assembly to the finished product. Current company certificate originals and candidate test reports were not established in the material reviewed. Actual incoming-material photo and document [9]

  1. Approve the configuration. Freeze the drawing, materials, locking, seals, grease and marking for a representative first article.
  2. Approve the evidence. Agree the lot identifiers, material/process records and finished inspection results you will receive.
  3. Control repeat orders. Require notification before changing material, housing, seal, lubricant, process or manufacturing site; retain a sample/record against the approved revision.

The dedicated contact identifies Wang Wenzhi, mobiles 18903191608 / 18103198797, and Dianli East Street, Linxi Bearing Industrial Park, Xingtai, Hebei. Confirm the engineering owner, sample receiving point, current production scope, quantity, delivery and warranty terms. No enquiry was sent during the review. Actual dedicated contact [10]

YOUR NEXT STEP

Prepare a VOST housed-unit and lot-acceptance enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Official brand and product publication actually readVOST Hebei Jujian · homepage ↗

    VOST site title and advertised focus; not independent approval or capacity audit.

  2. Official actual manufacturing descriptionJujian · dedicated company introduction ↗

    Temperature-controlled assembly, process traceability and application statements; order records/approvals not supplied.

  3. Official actual detailed family descriptionJujian · actual housed/insert bearing detail ↗

    Locking and housing alternatives; no full model/whole-unit rating established.

  4. Official process statement dated 16 January 2024Jujian · automatic lubricant filling ↗

    Uniform injection claim; candidate lubricant, fill tolerance and maintenance require agreement.

  5. Official actual closure/category listJujian · deep-groove product list ↗

    Open/shield/rubber/brass-cage alternatives; not equivalent ratings or stock.

  6. Official actual product detailJujian · 62 rubber-sealed bearing detail ↗

    General construction prose; exact model clearance/accuracy/grease/speed requires confirmation.

  7. Official actual product detailJujian · 302 tapered-bearing detail ↗

    Separation, arrangement and broad interchangeability wording; arbitrary mixing not approved.

  8. Official actual process statement dated 16 January 2024Jujian · pre-dispatch inspection statement ↗

    Every-bearing check claim; scope, methods and lot results require agreement.

  9. Official page dated 25 January 2024; original image actually viewedJujian · incoming-material image ↗

    Steel tubes and GCr15 material quality document; not company ISO or current buyer lot evidence.

  10. Official actual dedicated contactJujian · factory contact ↗

    Wang Wenzhi, mobile numbers and Dianli East Street; receiving/current scope needs confirmation.

Report a source correction → · Return to inquiry checklist ↑

Jujian published product scope reviewed

The manufacturer website describes ball bearings and housed inserts.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.