BearingIndex
THE BEARINGINDEX DIRECTORY

KGBAL

Taizhou Kejin, branded KGBAL, specialises in spherical plain bearings and rod ends. Its actual GE..UK-2RS drawing identifies a sealed steel/PTFE-fabric construction with different inner/outer ring treatments. Select the sliding pair, mounting fit and oscillation duty first, then verify candidate performance and any aerospace certificate or special-process scope separately.

KGBAL KEJIN · SPHERICAL PLAIN BEARINGS AND CONTROLLED SLIDING PAIRS

Select the sliding pair and mounting fit for the actual joint duty.

Taizhou Kejin Bearings Co., Ltd. (台州科锦轴承有限公司), using the KGBAL brand, dates its founding to 2001 and publishes spherical plain bearings, rod ends, hydraulic and pneumatic connection parts. Its selection service describes engineering support and custom design where catalogue products do not meet the requirement. Submit the joint drawing and operating cycle so the enquiry can reach the right product and validation route. Actual company scope [1] Actual selection/custom-design service [2]

Prepare a sourcing inquiry
01

Read the complete GE..UK-2RS construction before comparing equivalents.

The actual GE..UK-2RS drawing describes a maintenance-free, sealed steel/PTFE-fabric sliding pair. It identifies a heat-treated, hard-chrome-plated bearing-steel inner ring and a heat-treated, phosphated bearing-steel outer ring. These details came from the supplier’s actual drawing image, not a generic interpretation of the suffix. Confirm the current drawing revision and candidate materials/treatments before approving a replacement. Actual drawing and table, viewed in browser [3]

GE20 UK-2RS catalogue pointPublished valueBuyer check
Bore / outside diameter / inner-ring width20 / 35 / 16 mmVerify shaft, housing and shoulder geometry against the controlled drawing.
Outer-ring width C12 mmKeep inner/outer ring widths distinct in the mounting stack.
Approximate tilt angle9°Confirm actual installation clearance and required articulation.
Dynamic / static ratings45 / 104 kNRequest the applicable duty/life calculation and limits; these are not a universal allowable service load.
Sliding pair and sealsSteel/PTFE fabric; sealedConfirm liner, wear limit, sealing and maintenance rules for your exposure and motion.

The radial catalogue also lists other families, including GE..FW-2RS, ETL/XTL variants and inch-designation families. The rod-end catalogue lists CM/CF, GAR and other routes. A cross-reference or similar bore does not settle liner construction, outer-ring width, articulation, thread handedness or the housing strength of a rod end. Request a controlled comparison of the complete incumbent and proposed part. Actual radial-family listing [4] Actual rod-end-family listing [5]

02

Define the mounting fit and oscillation cycle together.

KGBAL’s fit guidance discusses cracking, creep/wear, reduced clearance, seizure and deformation associated with unsuitable installation fits. Give the actual shaft/housing tolerances, support geometry, material and temperature range; ask engineering to approve the fit and installed clearance for the selected sliding pair. Do not reuse a rolling-bearing fit or apply a blanket interference rule to every joint. Actual fit and tolerance guidance [6]

Specify radial/axial loads, shocks, oscillation angle/frequency, dwell and reversals, expected cycles, temperature, dirt/water/chemicals and corrosion exposure. For a sealed PTFE construction, agree liner wear, running torque, play and sealing acceptance. Ask for the precise lubrication/cleaning restrictions; do not add grease to a maintenance-free sliding pair without the supplier’s approved instruction.

The equipment page labels high/low-temperature oscillation testing, peel-strength testing, life testing, metrology, material examination and flaw detection. Request the tests relevant to the quoted liner and ring process, with specimen identity, conditions, calibration and pass limits. A photograph of a rig does not establish completed duty validation or accredited scope for every test. Actual named testing equipment [7]

  1. Review the joint design. Agree dimensions, articulation, fits, sliding pair, seals and thread/attachment details.
  2. Approve representative samples. Record initial dimensions, play and torque, then test the agreed load/motion/environment cycle.
  3. Inspect the end condition. Measure wear/play, liner and ring condition, torque and sealing against agreed limits.
  4. Control repeat manufacture. Link accepted material, liner bonding/treatment and inspection revisions to lot traceability and change notification.
03

Check the certificate, process and programme approval separately.

The AS9100D page displays an Intertek certificate image for Taizhou Kejin Bearings Co., Ltd. at Dongdu South Road, Xiahui Village, Shaojiadu Street, Linhai. The image names AS9100:D and ISO 9001:2015, a scope of design and production of joint bearings and machining of metal parts, issue date 3 December 2023 and expiry date 2 December 2026. This describes the displayed certificate; current status was not independently authenticated with the issuing body. Obtain the current original and verify entity, site, scope and status before approval. Actual certificate image viewed in browser [8]

The quality page says the joint-bearing inspection centre obtained Nadcap-NDT accreditation in October 2022. It also contains older ISO 9001:2008 and ISO/TS 16949:2009 development wording. Request the current applicable Nadcap certificate/scope and approved methods for the process used on your part; do not interpret the dated text as every process being accredited or as current automotive IATF certification. Actual dated NDT claim and quality-system wording [9]

For an aerospace enquiry, identify the programme/drawing authority and required product qualification, approved processes, material traceability, first-article and inspection documentation. A management-system certificate or NDT scope does not provide aircraft fitment approval, permission to substitute an incumbent bearing, or the approval of a specific liner/material process. Agree these deliverables with the customer’s quality and engineering teams.

04

Connect the drawing review to Kejin’s corporate sales and factory route.

The national standards platform lists Kejin among the drafting organisations for GB/T 12765-2023, spherical plain bearing mounting dimensions, and GB/T 304.3-2023, spherical plain bearing fits, both shown as current and implemented 1 December 2023. This independently supports those particular drafting contributions. It does not certify the proposed part or settle its application-specific fit and life. Actual mounting-dimension record [10] Actual fit-standard record [11]

Use the dedicated company contact: sales telephone +86-576-85622313, email [email protected], and Manager Wang, 18957657862. The footer gives the Linhai economic-development-area address on Dongdu South Road, Xiahui Village, Shaojiadu Street. The dedicated page also lists Guangdong, Wuxi and Suzhou offices. Confirm the contracting entity, production/inspection site and sample-receiving address for the quoted order. Actual corporate contact directory [12]

Some product-category sidebars instead show a Yuhuan address and a different phone/email. Do not route a technical enquiry using those inconsistent sidebar details without company confirmation. The dedicated contact and actual model detail’s [email protected] address provide the corporate enquiry route. Actual conflicting category sidebar [4] Actual model enquiry email [3] Dedicated company details [12]

Ask for the engineering owner, controlled proposal, stock or custom-build status, sample/serial lead time, tooling/qualification responsibilities, quote, packaging, warranty and change-control agreement. The selection page’s inventory and development claims are not a current allocation or promised completion date for your candidate. Actual selection-service scope [2]

YOUR NEXT STEP

Prepare a KGBAL joint-bearing enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Official actual company publicationKGBAL · company introduction ↗

    2001 founding, joint-bearing focus and application scope; rankings/customer claims not used as independent approval.

  2. Official actual engineering-service textKGBAL · selection service ↗

    Selection and custom-design route; no live inventory or delivery commitment verified.

  3. Official actual drawing images viewed in browserKGBAL · GE..UK-2RS drawing and table ↗

    Steel/PTFE, ring treatments and GE20 row; catalogue values not application qualification.

  4. Official actual family/category listKGBAL · radial spherical plain bearing families ↗

    Series choices and inconsistent sidebar details; family labels not complete construction.

  5. Official actual category listKGBAL · rod-end families ↗

    CM/CF/GAR and other families; thread/construction requires candidate drawing.

  6. Official actual technical guidanceKGBAL · fits and tolerances ↗

    Installation-fit failure modes; candidate fit must be approved against actual duty.

  7. Official actual equipment labelsKGBAL · testing equipment ↗

    Temperature oscillation, peel strength, life, material and metrology equipment; not completed lot reports.

  8. Official certificate image actually viewed in browserKGBAL · displayed AS9100D certificate ↗

    Displayed entity/site/scope and2023–2026 dates; issuing-body status not independently authenticated.

  9. Official actual dated quality/process claimsKGBAL · quality assurance ↗

    October2022 Nadcap-NDT and older system wording; current applicable scope requires verification.

  10. Primary actual current standard recordSAMR · GB/T12765-2023 ↗

    Mounting dimensions and Kejin drafting contribution; not candidate certification.

  11. Primary actual current standard recordSAMR · GB/T304.3-2023 ↗

    Fits, implementation date and Kejin drafting contribution; not application approval.

  12. Official actual sales and office directoryKGBAL · dedicated corporate contacts ↗

    Corporate email/phone/Manager Wang and regional offices; confirm exact contracted production/receiving route.

Report a source correction → · Return to inquiry checklist ↑

KGBAL published product scope reviewed

The manufacturer website describes spherical plain and rod-end bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.