BearingIndex
THE BEARINGINDEX DIRECTORY

La Leonessa Yancheng

La Leonessa Yancheng describes an Italian-invested slewing-bearing operation founded in 2011. Its published domestic production range is 400–2,000 mm outside diameter, with internal-geared, ungeared and flanged constructions. For a candidate assembly, obtain load-case calculations, mounting/drive interfaces, a controlled drawing and installation instructions. Distinguish the 2026 company-reported ISO surveillance audit from product-specific classification approval.

SLEWING SUPPORT · ENGINEER THE COMPLETE ROTATING ASSEMBLY

A slewing bearing needs a load case, a mounting plan and a drive interface.

La Leonessa Yancheng (牛力士轴承(盐城)有限公司) describes an operation established in 2011 through investment by Italian La Leonessa S.p.A., offering calculated, customized slewing-bearing solutions for China and Asia. Its certification/introduction material states a domestic production envelope of 400–2,000 mm outside diameter. Treat this as the manufacturer’s stated size envelope, not a load rating or proof that every Leonessa item is produced in Yancheng. Company introduction [1] Published domestic size range [2]

Prepare a sourcing inquiry
01

Describe the loaded machine before choosing a ring diameter.

The concrete-pump case discusses high overturning moments and stability requirements. It provides an application explanation, but no named bearing designation, complete load diagram or independently verified customer approval. Use it to frame an engineering discussion rather than to approve a pump or lifting-machine replacement. Actual concrete-pump application case [3]

  1. Define each operating state. Send axial and radial forces, overturning moment, their directions and where they act. Identify normal duty, start/stop, emergency and any other required design cases; state how these values were derived.
  2. Explain motion and environment. Give rotation or oscillation duty, speed, cycles, shock/vibration, exposure, temperature and maintenance access. Do not replace this information with the machine’s nominal tonnage.
  3. Include the supporting assembly. Provide mounting-plane drawings, available envelope, ring connection and supporting-structure stiffness information. Ask the supplier to identify its calculation assumptions and what needs approval by the machine designer.
  4. Release a named candidate. Obtain a controlled bearing drawing, load-capacity assessment and agreed acceptance criteria. Confirm separately any required analysis of bolts, support structure and gear drive.

No model-specific load, rotational-speed, moment or service-life rating was established from the viewed product pages. The size envelope alone cannot resolve these requirements.

02

Internal gear, no gear and flange construction create different interfaces.

The actual catalogue pages include single-row roller/internal gear, single-row ball/without gear and a Z-type external-geared single-row ball flange construction. The internal-geared page’s viewed drawing shows ring/roller components, mounting holes, seals and lubrication provision with dimension symbols. It is a geometry aid, not an order-specific rated drawing. Internal-geared roller construction and viewed drawing [4] Ungeared ball and flange listings [5]

Published routeInterface questions for your assemblyRequired release evidence
Internal-geared rollerPinion location, gear geometry, drive torque, backlash and available space inside the ring.Exact gear definition, mating-pinion arrangement and candidate drawing; confirm required tooth checks and calculation responsibility.
Ungeared single-row ballHow rotation is driven externally, which ring rotates and how loads enter both mounting faces.Complete mounting/drive arrangement and bearing selection for the actual load and motion duty.
External-geared flangeFlange interfaces, hole pattern, gear/pinion clearance and fastener access.Controlled flange/gear drawing, fastener arrangement and supporting-face acceptance requirements.

Specify hole count, pitch-circle dimensions, locating features, ring orientation and every supplied component. Similar outside diameters or broad construction names do not establish interchangeability. Ask whether the bearing, pinion, fasteners, lubrication fittings and installation support are included in the quotation.

03

Make mounting acceptance and a maintenance baseline part of delivery.

Before installation

Agree mounting-face flatness, cleanliness and the actual support arrangement with the bearing and machine designers. Obtain the approved fastener specification, tightening method and sequence for this assembly. A bearing inspection report cannot establish that the machine’s mounting face or bolt joint is acceptable.

Record the bearing identification, mounting checks and initial operating-clearance measurement before first operation. Keep the measurement method and operating conditions consistent for future comparisons.

After installation

The company’s maintenance publication discusses lubrication, bolt inspection, seal condition and clearance monitoring, including a baseline before initial operation. Those are useful handover topics; maintenance intervals and grease selection still need to match the supplied bearing and actual environment. Official maintenance discussion [6]

The official site published a Rev2 assembly and maintenance manual on 14 November2024. The publication page was read, but the linked PDF returned HTTP403 during this review, so its detailed contents and applicability were not verified. Request the current complete manual directly and have its revision identified in the order; do not assume the older website guidance supersedes it. Actual Rev2 publication and download route [7]

For acceptance, agree the dimensional/gear checks, material and heat-treatment evidence, traceability and any required functional inspection. Define who handles mounting supervision and a field complaint, what measurement records are needed, and whether those services are included. No response-time or on-site-service guarantee was verified.

04

Recent ISO audit news and workplace-safety recognition answer different questions.

A company announcement dated 28 May2026 reports that DNV representatives conducted annual surveillance of ISO9001, ISO14001 and ISO45001 on 27–28 April. This is a recent manufacturer report concerning management systems. Obtain certificate originals with entity, site, scope, number, validity and issuer-status evidence; the announcement itself is not an independently checked certificate database result. Actual 2026 surveillance-audit announcement [8]

The general certification page also mentions several classification societies, but does not establish the exact presently approved bearing, application, production site and validity from readable certificate particulars. If a vessel or other regulated project needs classification approval, name the required society, equipment and approval route, and request documents covering this supplied part. A management-system audit cannot substitute for that product/application approval. General certification claims and production envelope [2]

The Yancheng Emergency Management Bureau’s 31 August2026 announcement names 牛力士轴承(盐城)有限公司 at item210 among enterprises determined as level-three safety-production-standardization enterprises. It states a three-year validity period from announcement, subject to specified revocation conditions. This is a dated workplace-safety record; no later revocation/status search or bearing-quality approval is implied. Actual government announcement, item210 [9]

05

Separate manufacturing origin, contracting party and engineering support.

The domestic production envelope and Italian-investment history do not determine the origin of a particular quoted bearing. Request the manufacturing site, supplied brand/design owner, country-of-origin documents where required, and the exact legal seller for the candidate. For imported or group-supplied parts, confirm which entity handles warranty, replacement and local technical support. Company’s China/Asia positioning [1] Domestic production statement [2]

The dedicated contact page gives 65 Yandu East Road, Yancheng Economic Development Zone and +86 515 89026339. Confirm the receiving building, technical contact and delivery address before sending a sample or purchase order. Submit a complete load-and-interface package and request a drawing revision and calculation response, rather than asking for a price from outside diameter alone. Actual dedicated contact [10]

YOUR NEXT STEP

Prepare a Leonessa slewing-assembly enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Actual official introductionLeonessa Yancheng · company introduction ↗

    2011 investment/history and China/Asia customized-solution positioning; exact current ownership and order origin not independently checked.

  2. Actual official self-descriptionLeonessa Yancheng · certification and domestic production ↗

    400–2,000 mm domestic outside-diameter envelope and general society claims; no blanket current product approval.

  3. Actual official application explanationLeonessa Yancheng · concrete-pump case ↗

    Overturning moment/stability context; unnamed customer claims and rated model not independently established.

  4. Actual official detail and browser-viewed drawingLeonessa Yancheng · internal-geared single-row roller ↗

    Construction/interfaces visible; no order-specific numerical rating inferred.

  5. Actual official product detailLeonessa Yancheng · ungeared single-row ball listing ↗

    Read alongside actual flange detail at /falanxing/201.html; geometry families, no automatic interchangeability.

  6. Actual official text and linked maintenance graphic readLeonessa Yancheng · maintenance publication ↗

    Lubrication, bolts, seals and clearance topics; older general guidance not a universal interval or current-order instruction.

  7. Actual official publication pageLeonessa Yancheng · Rev2 manual publication, 14 November2024 ↗

    Manual/revision existence and download route read; linked PDF HTTP403, contents/applicability unverified. Sitemap /news/390.html failed404.

  8. Actual official announcement and browser readLeonessa Yancheng · DNV ISO surveillance news, 28 May2026 ↗

    Company-reported April27–28 ISO9001/14001/45001 audit; current original certificates and issuer status not independently verified.

  9. Original government announcement, actual full browser text readYancheng Emergency Management Bureau · 31 August2026 determination ↗

    Item210 exact company and conditional three-year workplace-safety-standardization recognition; no product certification or later status check.

  10. Actual official contactLeonessa Yancheng · dedicated contact ↗

    65 Yandu East Road and phone; exact contracting/manufacturing/receiving scope requires confirmation.

Report a source correction → · Return to inquiry checklist ↑

La Leonessa Yancheng published product scope reviewed

The manufacturer website describes custom slewing bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.