BearingIndex
THE BEARINGINDEX DIRECTORY

LK

LK / Quanzhou Guoxing focuses on mounted insert-bearing units with cast and pressed housing forms. Its standing, sliding-block and suspended housings require different mounting and service interfaces. Obtain the full insert/housing drawing and locking arrangement before approving a replacement; the historical catalogue has incomplete and placeholder records.

LK · CAST AND PRESSED MOUNTED-BEARING HOUSINGS

Start with the housing’s mounting role, then approve the insert and lock.

Quanzhou Guoxing Bearing Co., Ltd. (泉州国兴轴承有限公司) identifies LK as its brand and mounted insert-bearing units as its main product. Its official catalogue separates cast standing, flange, sliding-block, suspended and pressed housings. That variety helps frame the enquiry, but each offer needs a current drawing and a defined insert/housing combination. Official company and brand [1]

Prepare a sourcing inquiry
01

Standing, sliding-block and suspended housings need different drawings.

Actual official detailInformation to releaseWhat the family page does not settle
Standing housing with set-screw insertShaft centre height, base width, hole/slot spacing, mounting surface, housing material and fastening access. Actual standing-unit page [2]The full insert/bore/suffix, dimensions and load/speed approval.
Sliding-block housing with set-screw insertGuide-slot geometry, adjustment travel, retention and tensioning interface, plus shaft and bearing position. Actual sliding-block page [3]The complete tensioning mechanism, travel stop, guide fit and supplied hardware.
Suspended housing with set-screw insertSupport/bracket connection, installation orientation, available envelope, shaft access and maintenance clearance. Actual suspended-unit page [4]The machine bracket or complete suspended support assembly.

The reviewed details provide category names and photographs without a controlled dimensional table. Request the exact unit code and revision-controlled drawing; do not infer a bolt pattern, load rating or casting grade from a similar photograph. For replacement, provide the original designation, mounting measurements and failed-part condition together.

The catalogue also separates narrow and high-centre standing forms, adjustable flange forms and pressed housings. Confirm the required architecture and actual envelope before comparing quotations. A housing that accepts a similar insert can still have a different mounting role or structural requirement. Actual separate catalogue categories [8]

02

Confirm the lock and accessories as part of the supplied unit.

The three mounted-unit details above explicitly name set-screw arrangements. A separate actual product detail is titled insert bearing with adapter sleeve; the catalogue identifies a UK entry. Keep the locking specification with the full bearing designation instead of ordering all forms as the same shaft fit. Actual adapter-sleeve detail [5] Catalogue UK entry [8]

Set-screw unit

Release shaft diameter and tolerance, surface condition, available locking position and duty. Ask for the approved screw type, tightening procedure, permitted speed/load and rotation requirements for the offered insert.

Adapter-sleeve arrangement

Confirm bearing bore/taper, sleeve designation and shaft interface, and whether sleeve, locknut and locking device are included. Obtain the actual mounting/clearance instructions and access needed to fit and service it.

For either arrangement, specify operating loads, belt/tension forces where relevant, speed, vibration, alignment, temperature and environment. Agree housing/insert seating, seal and grease configuration, lubrication access and installed rotation checks. Do not apply a generic permissible misalignment or a maintenance-free claim without selected-unit data.

The official catalogue also contains an “xxxx” product with “5555” identifier. It has not been treated as a real model specification. Ask for a signed technical offer resolving the exact code and drawing before purchasing any unclear record. Actual catalogue record [8]

03

The housing-line project is evidence to investigate, not a delivery-capacity receipt.

The Quanzhou Taiwanese Investment Zone notice dated 8 December 2025, concerning proposed subsidies for 2024 technical-upgrade projects, lists Guoxing’s bearing-housing production-line expansion as entry 3. This is a dated proposed-subsidy project record. It does not establish current completion, available output or qualification of your selected casting and assembly. Actual government project notice [6]

The company website describes machinery and annual production. Request current, order-specific manufacturing responsibility: who makes the housing/casting, performs machining and seating inspection, manufactures or buys the insert, and assembles the final unit. Confirm the actual production site and subcontracted steps rather than turning general equipment counts into a capacity commitment. Supplier production description [1]

  1. Approve the technical offer. Freeze insert/housing drawings, material, locking accessories, seals, lubricant and mounting interfaces.
  2. Inspect a traceable sample. Agree dimensional and material checks, housing/insert fit, lubrication access and rotation acceptance under the intended installation.
  3. Validate the machine duty. Check alignment, running behaviour, temperature and representative load/contamination with the buyer’s engineering team.
  4. Control repeat batches. Retain lot markings, inspection evidence, approved component sources and written change approval.

Request current quality-system or application evidence where required by the buyer, identifying entity/site/scope and the selected model. Broad use in agriculture, food or mining machinery does not independently establish programme approval or a specific service life.

04

The contact page gives an office location: confirm the actual factory visit.

The official contact explicitly labels its location office address: Nanshan Road intersection, Quanzhou Taiwanese Investment Zone. It lists 0595-87585198 as both telephone and fax and [email protected]. Confirm the responsible engineer, current factory/audit address, receiving point and contracting/payee name before visiting or ordering; the office description is not a complete manufacturing-site address. Actual contact labels [7]

Send the drawing and duty together with sample and serial quantities. Request an itemised quotation stating insert-only or complete-unit scope, sleeve/lock/fastener inclusion, samples, tooling where applicable, serial schedule, packing/corrosion protection and delivery terms. Confirm available stock by exact code and lot separately from the catalogue listing.

Keep the approved configuration and installation/maintenance documents with the order. Agree claim evidence such as lot identification, mounting and shaft measurements, lubrication history and observed running conditions so a service issue can be assessed against the actual supplied unit.

YOUR NEXT STEP

Prepare an LK housing-and-insert enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Official actual company pageGuoxing · company profile ↗

    LK brand, mounted-bearing focus and supplier production descriptions; current capacity and programme approval not established.

  2. Official actual category detailGuoxing · standing mounted unit ↗

    Standing/set-screw family and photograph; selected-unit controlled dimensions required.

  3. Official actual page and browser viewGuoxing · sliding-block mounted unit ↗

    Sliding-block/set-screw housing family; tensioning assembly and exact geometry not established.

  4. Official actual category detailGuoxing · suspended mounted unit ↗

    Suspended/set-screw family, not a complete machine support design.

  5. Official actual titled detailGuoxing · adapter-sleeve insert detail ↗

    Separately named adapter-sleeve arrangement; exact bearing/sleeve and inclusion to confirm.

  6. Government actual notice/tableQuanzhou investment zone · proposed technical-upgrade subsidies ↗

    2025-12-08, 2024 project proposed-subsidy row3 housing-line expansion; no current completion/output receipt.

  7. Official actual dedicated contactGuoxing · contact ↗

    Office at Nanshan intersection, same telephone/fax number and email; precise manufacturing/receiving route to confirm.

  8. Official actual catalogue recordsGuoxing · product catalogue ↗

    Separate housing categories and UK listing; xxxx/5555 placeholder excluded as real model evidence.

Report a source correction → · Return to inquiry checklist ↑

LK published product scope reviewed

The manufacturer website describes housed insert ball bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.