BearingIndex
THE BEARINGINDEX DIRECTORY

NJJ

NJJ / Jinjinnaichi: miniature and thin-section deep-groove ranges, separately listed flexible and four-point-contact products.

NJJ · FLEXIBLE RINGS · FOUR-POINT · MINIATURE

Start with the bearing’s role inside the assembly.

NJJ’s official catalogue offers conventional miniature/thin-section bearings alongside F-8 through F-40 flexible references and a distinct 4P four-point-contact range. A wave-generator component, a four-point support and a small flanged bearing require different interface and test evidence. Retain the actual product reference and proposed manufacturing build throughout the enquiry. Flexible range [1] Four-point range [2] Company scope [3]

Prepare a sourcing inquiry
01

F-20 needs the cam and flexspline conversation.

NJJ’s F-20 page describes a flexible bearing with bearing-steel rings/rolling elements and a nylon cage, with the outer ring deforming for a harmonic-drive application. Treat this as a component proposal requiring actual material/BOM and assembly qualification; it is not a complete reducer, a robot-joint torque rating or an aerospace approval. F-20 product and original table [4]

Published F-20 fieldValueWhat to include in the approval drawing
Inner-ring d / width B35.56 / 8.13 mmActual cam interface, fit, section and mounting datum.
Outer-ring D / width C49.073 / 7.24 mmFlexspline interface and separate outer-ring width; do not reduce the build to one common B.

These are the labels and numbers in NJJ’s original image table, not an installed ellipse specification. Provide the reducer geometry and operating cycle, request the controlled free/installed ring sections and permitted deformation, and agree installed torque, temperature and fatigue-test conditions. Confirm cage grade, grease and traceability. The generic product text includes broad mechanism/application claims without an order-specific test report; do not transfer them into a guaranteed reducer ratio, stiffness or service life.

02

4P6900 is a separate design enquiry.

The original four-point table gives 4P6900: d10, D22, B6 mm, with dynamic/static rating fields of 1590/1270 N. NJJ describes a Gothic-arch raceway, but the reviewed data does not specify the offered contact angle, clearance/preload, mounting tolerances or a permitted moment-load envelope. Request the actual section and load/deflection information for the combined operating loads. 4P6900 original [5]

Do not replace an approved pair by prose alone

The product description compares a four-point bearing with a back-to-back angular-contact arrangement. That wording does not approve an interchange in your assembly. Compare supports, fits, stiffness, axial/radial duty, moment, speed and temperature, then qualify the proposed build with numerical acceptance.

The category shows two entries labelled 4P6804 with different destination pages. Retain the supplier’s complete offered drawing/reference rather than counting duplicate labels as verified separate variants. Broad spindle, wind-yaw or robot application wording is not evidence that this small reference is approved for those systems. Actual category entries [2]

03

Resolve F608’s flange field before machining the housing.

The F608 product prose gives bore8 and outside diameter22 mm and describes flange OD22 mm. The same page’s original table gives the F608 row d8 / D22 / Df25 / Bf1.5 / B1 7 mm. The flange-OD fields conflict; do not silently choose the table value as a production specification. Obtain the supplier-controlled drawing and confirm the flange seat and axial stack before approving the sample. F608 prose and original table [6]

The site also publishes an MR82 miniature reference. Its generic low-friction/high-speed description is not a numerical running-torque, noise or precision guarantee for your instrument or motor. Specify closure, clearance, lubricant, materials and installed fits, and agree the noise/torque method, fixture and limits. A dental-equipment application statement on the homepage does not establish sterilisation resistance, medical approval or a particular handpiece build. MR82 entry [7] Homepage application wording [8]

04

Identify the manufacturer, trader and covered plant.

The contact page lists both Ningbo Zhenhai Jinjinnaichi Bearing Co., Ltd. and Ningbo Sinoring International Trading Company Limited, with the contact address No.9 Fengshuidun Road, Luotuo, Zhenhai. Confirm who contracts/invoices/exports the order and who manufactures, owns the quality records and handles nonconformances. Do not infer a particular ownership or agency arrangement from the shared contact page. Published contacts are +86-574-86583010 and [email protected]. Actual contact page [9]

The honour gallery’s ISO9001:2015 image covers deep-groove ball-bearing production and prints an expiry in October2022. Its displayed registration/physical addresses are Shangxin Village/Jinju Road rather than the current Fengshuidun contact. Obtain a current issuer-verifiable certificate and site annex for the offered plant; this historical image does not establish current certification. The same gallery includes software-copyright documents, trademark material, a television advertising plaque and association membership. Those items are distinct from product qualification or an active system certificate. Original gallery, visually read [10]

The government-hosted 2024 enterprise technical-R&D-centre list names the Jinjinnaichi low-noise precision-bearing centre with the exact legal company as supporting entity (entry388). This is dated recognition of the named centre, not an independent audit of a particular bearing’s noise, robot suitability or current system status. Original government list [11]

  1. Agree the build: resolve F608 or flexible-ring drawing fields and document materials, closure/cage, grease, clearance and revision.
  2. Review the offered production route: request part-linked process, measurement/calibration and lot records. Facility photographs and the stated130+ lines do not establish order capacity or numerical capability.
  3. Qualify installed duty: retain sample lot and controlled report, approve the relevant motor or reducer assembly trial, then define repeat-production sampling and change/requalification triggers.

Confirm a dated production slot, delivery, technical-review responsibility and warranty/nonconformance terms in the quotation. Manufacturer equipment gallery [12]

YOUR NEXT STEP

Prepare an NJJ role-specific enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Manufacturer reference listNJJ · flexible category ↗

    Actual F-series entries, not a complete reducer or system approval.

  2. Manufacturer reference listNJJ · four-point category ↗

    Actual4P entries including repeated4P6804 labels; no inferred variant count.

  3. Manufacturer statementNJJ · company scope ↗

    Small/thin/nonstandard range and line descriptions; no available capacity or capability audit.

  4. Manufacturer product/table, visually readNJJ · F-20 original product ↗

    Distinct inner/outer dimensions and advertised material/role; installed ellipse and fatigue qualification not supplied.

  5. Manufacturer product/table, visually readNJJ · 4P6900 original product ↗

    10/22/6 and1590/1270N; no contact-angle/preload or moment/stiffness approval.

  6. Manufacturer prose/table discrepancyNJJ · F608 original product ↗

    Prose flangeOD22 vs originalDf25; Bf1.5/B1 7 fields retained, controlled drawing required.

  7. Manufacturer product publicationNJJ · MR82 product ↗

    Actual reference and generic text; no numerical noise/torque or installed precision guarantee.

  8. Manufacturer application statementsNJJ · homepage applications ↗

    Dental and motor application statements do not establish medical/sterilisation or specific assembly qualification.

  9. Manufacturer contact publicationNJJ / Sinoring · official contacts ↗

    Two named entities and Fengshuidun9/contact routes; ownership/agency and contracting role not inferred.

  10. Manufacturer original images, visually readNJJ · honour gallery ↗

    Historical ISOexpiry2022 and old site, software/trademark/advertising/association documents; current system status unconfirmed.

  11. Government original PDFNingbo · 2024 enterprise technical-R&D-centre list ↗

    19-page original, entry388 onPDF18 supporting exact entity; no individual bearing performance endorsement.

  12. Manufacturer facility publicationNJJ · equipment gallery ↗

    Published plant/equipment images, not order-level calibration/capability or schedule.

Report a source correction → · Return to inquiry checklist ↑

NJJ published product scope reviewed

The manufacturer website describes miniature and thin-wall deep groove bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:34

Source documentation retained for editorial review.