BearingIndex
THE BEARINGINDEX DIRECTORY

Shengya

Zhejiang Shengya publishes tensioner-wheel, clutch-release and ball-cage-category products and accepts nonstandard bearing enquiries. Its LZ7170, LZ7200 and LZ7201 details state distinct outer diameter, height and bore dimensions. Use those as envelope checks, then obtain the complete interface and vehicle/duty evidence rather than inferring compatibility from a model name.

SHENGYA · AUTOMOTIVE BEARING AND NONSTANDARD INTERFACES

Separate a bearing envelope from a verified vehicle replacement.

Zhejiang Shengya Bearing Technology Co., Ltd. (浙江升亚轴承科技有限公司) reports a manufacturing history beginning in 1996 and offers small/medium bearings and nonstandard shapes. The current catalogue groups clutch-release bearings, tensioner wheels and a “ball-cage” category. Start with the actual product detail, then define the assembly it must fit and the evidence needed to approve it. Official company scope [1]

Prepare a sourcing inquiry
01

Three LZ details show why the full envelope matters.

The actual product descriptions publish outer diameter × height × inner diameter in that order. Preserve those labels when transferring data to an enquiry: treating the first value as a bore would select the wrong part.

Published modelOuter diameterHeightInner diameter
LZ7170 [2]30 mm25 mm11 mm
LZ7200 [3]62 mm28.5 mm12.5 mm
LZ7201 [4]68 mm30.5 mm24 mm

These are candidates in the tensioner-wheel category, not interchangeable alternatives. Ask for a section drawing defining the pulley running surface, belt width/profile, contact track, bearing location, spacers, mounting bore and axial offset. A height entry does not tell the buyer the installed belt plane or clamping stack.

For a replacement request, identify the original part number, engine/vehicle variant and installation position, and supply the existing assembly drawing or sample. Confirm whether the offer is a bearing, pulley with bearing, or a complete tensioner with bracket/spring/damping parts. The three detail pages do not establish those complete-kit contents or vehicle approvals.

Provide belt forces and speed, starts/stops, temperatures, contamination and expected duty. Agree runout, mounting torque, rotational resistance, noise and seal/grease requirements with the supplier, followed by representative belt-drive endurance tests.

02

Read the supplied component before interpreting its category name.

The HY-6006 release-bearing detail gives outer diameter 82 mm, height 16 mm and inner diameter 50 mm. An envelope is a useful first check, but does not define the clutch contact face, guide sleeve, carrier/fork interface, stroke or working preload. Ask for those details and the complete part supplied. Actual HY-6006 detail [5]

The actual “球笼” detail contains a bearing table with new/old designations. BR-30001 maps to 160106/6006-2RS with 30 × 55 × 13 mm; BR-30002 maps to FD-1-711-8/6006W19 with 30 × 55 × 19 mm. The same bore and outside diameter therefore leave a different height. The table also specifically describes BR-45001 as having a spherical outer ring. Do not erase that shape distinction or market this category as a complete CV-joint assembly from its name alone. Actual bearing table [6]

Clutch-release enquiry

State clutch type, contact geometry, actuation/guide arrangement, stroke, axial load, rotational duty and operating temperature. Request the actual carrier, seals, grease and any self-alignment specification, plus the acceptance tests.

Table-based replacement

Preserve new/old designations and complete suffixes. Compare bore, outer profile, height, retention and tolerances on a controlled drawing; request written equivalence for the intended assembly instead of treating a catalogue cross-reference as universal fit.

03

Make the nonstandard request measurable before tooling starts.

Shengya explicitly accepts nonstandard and special-shaped bearing work. Provide a drawing revision covering ring/envelope geometry, material and heat treatment, clearances, seals, lubrication, mating fits and critical dimensions. Agree design responsibility, feasibility review, tooling/sample ownership and which changes require buyer approval. Official nonstandard scope [1]

The company reports annual capability of 10 million small/medium bearings and shows facility/equipment images. This is its general capability statement, not present stock or allocation for a specific LZ or custom part. Request a production plan and inspection route for the actual item.

The government-hosted nine-page notice from the Taizhou Science and Technology Bureau, dated 6 June 2022, recognises the first 2022 batch of provincial technology-based SMEs. Page 6, entry 183 names Shengya in Wenling. This dated administrative recognition is not IATF certification, vehicle qualification or approval of a bearing design. Actual notice, cover and annex read [7]

  1. Approve drawing and material evidence. Require lot-linked critical dimensions, ring material/heat-treatment and agreed seal/grease identification.
  2. Approve the intended duty. Use representative belt-drive or clutch tests, recording loads, speeds, temperature, duration and failure criteria.
  3. Control serial changes. Freeze the approved part, process and inspection plan; require notice for material, tooling, grease/seal or production-site changes.

Where automotive sourcing requires a current management-system certificate, customer-specific approval or part-submission package, obtain it for the exact legal entity, site and product. Do not substitute the technology-SME entry or general company history.

04

Use the Wenling contact route with the original-part evidence attached.

The dedicated contact gives 98 Minhe Road, Building 2, east side, floors 1–5, Zeguo, Wenling, Taizhou and +86-18257616666; the site’s contact panel lists [email protected]. Confirm the current audit and receiving location, contracting/invoicing entity and responsible application engineer. The reported 1996 manufacturing history should not replace a current business licence. Official contact page and panel [8]

Send the original-part identifier, controlled drawing or sample, required assembly contents and duty/qualification plan. Request a quotation separating the bearing/pulley/carrier, tooling and sample tests where applicable, with written lead time, packing, traceability, warranty and claim procedure.

YOUR NEXT STEP

Prepare a Shengya tensioner, release or nonstandard-bearing enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Official company textShengya · company introduction ↗

    Reported1996history, general10millionannual capability and nonstandard scope; no current allocation/approval.

  2. Official product detailShengya · LZ7170 ↗

    OD30/height25/bore11mm; no complete vehicle/duty approval.

  3. Official detail read in browserShengya · LZ7200 ↗

    OD62/height28.5/bore12.5mm and tensioner-wheel category.

  4. Official product detailShengya · LZ7201 ↗

    OD68/height30.5/bore24mm; mounting offset and full kit not inferred.

  5. Official product detailShengya · HY-6006 ↗

    Release category OD82/height16/bore50mm; clutch interfaces require drawing.

  6. Official actual HTML table also read in browserShengya · ball-cage-category bearing table ↗

    BR new/old designations, dimensions and spherical-outer45001; not full CVjoint claims.

  7. Primary9-pagePDF actually read; cover rendered and viewedTaizhou Science and Technology Bureau · first2022provincial SME recognition ↗

    6June2022notice, page6entry183Shengya; dated administrative recognition rather than automotive/product certification.

  8. Official contact textShengya · dedicated contact ↗

    Minhe98Building2eastfloors1-5, phone and site email panel; confirm current contract/receiving details.

Report a source correction → · Return to inquiry checklist ↑

Shengya published product scope reviewed

The manufacturer website describes small bearings for automotive and machinery applications.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.