BearingIndex
THE BEARINGINDEX DIRECTORY

Sihai

Cixi Sihai: conventional deep-groove and separately catalogued automotive bearing references.

SIHAI · AUTOMOTIVE REFERENCES · DEEP-GROOVE

A similar number can hide a different axial fit.

Cixi Sihai’s company introduction names automotive alternators, starter motors, tensioners and overrunning devices as application routes. Its original automotive catalogue provides actual dimensions and build notes; those are a stronger starting point than an application label, but still require qualification in your particular assembly. Company application statement [1] Automotive table [2]

Prepare a sourcing inquiry
01

Compare the published width before approving a replacement.

Same bore / ODAutomotive referenceOrdinary referenceBuyer decision
12 / 28 mm63001 · B12 mm6001 · B8 mmA 4 mm width difference changes the axial interface; check shoulders, spacer, retention and closure section.
12 / 32 mm62201 · B14 mm6201 · B10 mmEqual bore/OD does not establish assembly interchangeability or equal installed clearance.

All dimensions above are transcribed from Sihai’s own original image tables. The automotive table also lists B8—79D (8/23/11 mm) and B8—85D (8/23/14 mm); preserve the complete designation and request a controlled drawing instead of quoting “8×23 bearing.” These are catalogue entries, not a confirmed stocked build or vehicle-model fitment. Automotive original [2] 6000 original [3] 6200 original [4]

The conventional drawing displays Z, ZZ, ZX, 2RS, 2RZ and ZZX variants, while the automotive drawing displays 2RS. Ask for the offered variant’s actual section, marking and BOM: the illustration is not proof that every row is available in every closure. Keep shaft/housing fits, corner clearance and axial mounting dimensions on the approved drawing.

02

Turn the automotive build notes into measurable requirements.

The automotive table states high-temperature/high-speed generator grease, C3 clearance and high-temperature seal material. Its heat-treatment note also describes high-temperature tempering and low-temperature treatment. These are manufacturer statements without a named grease, seal compound, numerical temperature range or offered-part process record. Obtain those details before specifying an operating envelope. Original table notes [2]

Alternator or starter position

Identify the actual position and operating cycle. Provide mounted speed, radial/axial loads, belt load where applicable, temperature history and start-stop duty. Agree grease identity/fill, seal contact form and material, supplied clearance and the acceptable mounted condition with the intended fits.

Tensioner or overrunning device

Define whether the quotation is for the bearing or a complete mechanism. Supply the mating assembly drawing and retention/alignment requirements; request the actual load/duty test and assembly approval. Sihai’s company application statement does not establish a clutch design, complete tensioner supply or approval for your vehicle.

The catalogue separates grease and oil limiting speeds. Treat those as catalogue fields requiring the offered build and test conditions, not a universal limit for a sealed automotive assembly. Approve noise/torque, running temperature and durability against the actual installation and numerical acceptance conditions.

03

Manufacturing-system scope and product-design approval are separate.

The manufacturer’s Chinese and English IATF16949:2016 images state miniature deep-groove ball-bearing manufacture and explicitly exclude product design. They print a registration date of 15 May 2024 and expiry of 14 May 2027, and identify Longquan Village, Henghe Town, with a more specific provincial-road site description. These are read manufacturer-displayed documents; active status has not been independently confirmed in this review. Certificate gallery [5]

The same gallery includes older ISO/TS16949:2009 material and a 2007 enterprise plaque. Keep these historical items separate from a current system record. The homepage’s ISO9001/TS16949 wording also differs from the company page’s IATF16949/ISO14001 statements; request the current certificate set, manufacturing scope, covered address and verification result rather than merging all labels into an “automotive certified” badge. Homepage wording [6] Company wording [1]

Who controls the bearing design?

For a buyer-designed build, agree drawing ownership, technical review and change authorisation. If the supplier proposes a different seal, grease, clearance, width or material, require the controlled proposal and requalification decision. A system certificate with a design exclusion does not approve an unreviewed product redesign.

Ask for current issuer/IATF verification and a readable original/site annex. The issuer’s HTTPS page presented a certificate-authority error. Its public HTTP query form was readable, but the query button was obstructed by the page layout after the company name was entered, so no status result was obtained. These access results do not establish an invalid supplier certificate. Issuer query entry [7]

04

Connect the sample, actual line and repeat order.

  1. Freeze the offered build: reference/drawing revision, complete closure/BOM, clearance, grease identity/fill, materials and markings. Reconcile any dimensional difference with the actual assembly.
  2. Review the relevant process: request part-linked manufacturing/heat-treatment route and inspection/calibration records. The company’s production-line/output figures and facility gallery do not establish a currently available slot or numerical process capability for your part.
  3. Approve the sample and installed trial: agree measurement methods, sample quantity, noise/torque and duty-test criteria, then retain the tested lot and reports. For automotive programmes, request the customer-required approval documents and production-control evidence.
  4. Release the repeat order: define lot traceability, sampling, change notification, nonconformance handling, quantity, delivery date and warranty terms in the confirmed quotation.

Sihai’s contact page distinguishes sales (0574-63261640, Ms Yang) from purchasing (0574-63261286), and publishes [email protected] and Longquan Village, Henghe. Buyers should use the sales route and match the contracting entity and plant documents to 慈溪市四海轴承有限公司. Contacts [8] Facility gallery [9]

The government-hosted 2024 third-batch technology-SME list identifies the exact company at entry 804, registration 2024330282A8006108. This is dated entity context, not a product certificate, named OEM endorsement or current capacity audit. Original government list [10]

YOUR NEXT STEP

Prepare a Sihai automotive-reference enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

85 model records
Model / bearing familyManufacturerBore dOutside DWidth B / T / LDetails

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Manufacturer statementSihai · company introduction ↗

    Actual application and system statements; no named OEM, vehicle fitment or available capacity inferred.

  2. Manufacturer model image, visually readSihai · automotive original table ↗

    Full references/dimensions and generator grease/C3/seal notes; no named material or part approval supplied.

  3. Manufacturer model image, visually readSihai · 6000 original table ↗

    6001 width and actual closure illustrations; illustrated variants not assumed available for all rows.

  4. Manufacturer model image, visually readSihai · 6200 original table ↗

    6201 width and separated grease/oil speed fields; no installed assembly approval.

  5. Manufacturer original images, visually readSihai · honour/certificate gallery ↗

    IATF2024/2027 dates, miniature manufacture/design exclusion and historical TS material; current status unconfirmed.

  6. Manufacturer publicationSihai · homepage ↗

    6–35mm bore and older ISO9001/TS wording, distinct from current about-page statements.

  7. Primary issuer entry, access limitedCASC · certificate-query entry ↗

    HTTPS certificate-authority error; publicHTTP form entered, button obstructed by layout; no supplier certificate status result.

  8. Manufacturer contact pageSihai · sales and purchasing contacts ↗

    Distinct sales/purchasing routes and Longquan site; current quotation contact to confirm.

  9. Manufacturer facility publicationSihai · production equipment gallery ↗

    Published gallery, not order-level capability/calibration or available production capacity.

  10. Government original PDFNingbo · 2024 third-batch technology-SME list ↗

    115-page original downloaded, entry804 onPDF33 exact company/registration; dated entity evidence only.

Report a source correction → · Return to inquiry checklist ↑

Sihai published product scope reviewed

The manufacturer website describes deep groove bearings for motors and automotive use.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:34

Source documentation retained for editorial review.