BearingIndex
THE BEARINGINDEX DIRECTORY

THT

THT is presented by Shanghai Laigong as its precision-bearing brand for machine-tool spindles. The official site lists 70-series angular-contact variants and publishes a spindle-bearing image catalogue with separate contact-angle and oil/grease speed columns. A useful enquiry must define the matched arrangement, preload, lubrication and whole-spindle acceptance; a series name or catalogue speed is not a validated installed-spindle result.

THT MACHINE-TOOL BEARINGS · MATCH THE SET AND THE SPINDLE DUTY

Specify the bearing arrangement before comparing a spindle-bearing quote.

Shanghai Laigong Precision Bearing Co., Ltd. (上海莱工精密轴承有限公司) presents THT as its own brand for precision and high-precision bearing work. Its company image says it was established in 2007 and describes angular-contact, cylindrical and thrust products alongside spindle and motion components. These are company statements; the practical buying route is to define whether you need bearings, a matched bearing set, or an entire spindle. Official brand statement [1] Company page and original introduction image actually viewed [2]

Prepare a sourcing inquiry
01

Carry the complete designation, arrangement and preload into the quote.

The 20 June 2022 70-series detail lists variants such as 7005C, 7005AC and 7005BQ. The actual listing does not define every suffix or a full matched-set specification. Its 9 April 2009 angular-contact article names 718, 719, 70, 72 and 2344 and discusses paired/multiple arrangements and opposing axial loads. Those older pages guide the questions to ask; they do not establish current stock, a universally interchangeable replacement or every candidate’s grade. Actual 70-series designation list [3] Dated angular-contact article [4]

SpecifyWhy it matters hereRequest with the quote
Complete designation and angleC, AC and other listed suffixes cannot be discarded from a spindle replacement.Supplier’s controlled suffix key, drawing, dimensions, contact angle, cage and accuracy class with applicable standard/edition.
Matched arrangementA single bearing and a paired/multiple set have different axial and mounting responsibilities.Arrangement drawing, set identification, orientation/marking, matching method and permitted replacement policy.
Preload and mountingA correct envelope does not resolve the assembled bearing condition.Preload/clearance target and verification conditions; shaft/housing fits, shoulders, spacers and installation instructions.
Speed, duty and lubricationContact angle and lubricant columns are separated in the published image catalogue.Limits for the exact supplied set under the specified speed/load/duty, lubrication and cooling—not a copied base-series number.

The original bearing-introduction image describes commonly used 15° (C), 25° (AC) and 30° (A) angles and separate C/AC, grease/oil columns. For example, its H7005 row gives 25 × 47 × 12 mm, with different angle/lubrication speeds. Use that as evidence of the distinctions to preserve, not as proof that a quoted 7005BQ or mounted set has any of those ratings. The image’s version and current candidate approval were not established. Original image catalogue, actual first table viewed [5]

02

Resolve the cylindrical support and axial location as one arrangement.

The 9 April 2009 cylindrical article explains radial support, axial movement and combination with a separate axial-bearing arrangement. Its title says “NN30K, N10” while the body discusses “N30” and “NN30”. Do not silently correct that discrepancy into a candidate designation. Obtain the exact model/drawing and have the supplier identify the locating and floating roles in your spindle. Actual title/body wording [6]

Radial support proposal

Supply spindle loads, shaft/housing dimensions, fit/clearance requirements and axial travel. If the candidate uses a tapered bore, request its actual taper, mounting procedure and clearance-setting method rather than assuming a suffix is sufficient.

Axial-location proposal

Show the separate thrust or angular-contact support, both axial load directions and spacer/shoulder interfaces. Require a coordinated arrangement drawing and mounted acceptance criteria; a cylindrical radial part alone does not settle axial restraint.

For a replacement, retain the original arrangement drawing and full markings before ordering. A family label or photograph cannot establish matched dimensions, fits, clearance or compatibility with the remaining bearings.

03

Match the acceptance test to the scope you are actually buying.

The official product inventory includes bearings, CNC-lathe electric spindles, mechanical spindles and other spindle categories. The actual CNC-lathe detail dated 20 July 2018 presents an image/category but leaves model and dimensions blank; its displayed 0-yuan field is not a usable quotation. Ask for the current controlled configuration and commercial offer. Actual product inventory [7] Actual lathe-spindle detail and empty fields [8]

  1. Bearing-only purchase. Agree dimensional/rotational accuracy, matching/preload evidence, material/lot traceability and lubrication/installation instructions. Define who assembles and verifies the spindle.
  2. Complete spindle purchase. Add nose/interface and mounting drawings, drive/electrical and cooling requirements where applicable, lubrication, orientation and operating duty. Agree runout, vibration, thermal behaviour and functional test conditions for the complete assembly.
  3. Replacement/failure project. Provide original markings, arrangement and operating history, plus vibration/temperature/runout observations and lubricant condition. Approve a documented corrective proposal before repeat production.

The company page captions contour/coordinate, hardness, roundness, roughness and length measurements. Request the applicable instruments, calibration and candidate/lot results rather than treating equipment pictures as inspection records. Its 18 September 2009 spindle-balance article discusses rotor balance and resulting vibration/heating; that is background, not proof that your assembly was balanced to an agreed criterion. Actual inspection captions [2] Dated spindle-balance article [9]

04

Confirm the manufacturing site and the person responsible for the set.

The contact page explicitly labels Room 309, Building B, 958 Kangqiao East Road, Pudong, Shanghai as the Shanghai liaison office. It publishes Liu Chao, 021-58126027, 13501946162 and [email protected]. Confirm the actual manufacturing, assembly, inspection and receiving sites; a liaison address should not be turned into a factory-location claim. Actual office/contact wording [10]

Current certificate originals, an independently verified capacity statement and an order-specific test record were not established from the pages read. Government/association/platform searches did not yield a usable exact-entity primary record in this review; a similarly named precision-electromechanical entity is not substituted. Request the legal supplier, current applicable certificate scope and traceable inspection documents as part of qualification. Missing research evidence is not a determination that the company lacks certification.

Keep the bearing-set engineering approval separate from the commercial quote. Confirm sample/first-article quantity, matching responsibilities, delivery date, warranty scope and the inspection report you will receive. No enquiry was sent during the review.

YOUR NEXT STEP

Prepare a THT spindle-bearing or spindle-assembly enquiry

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Official brand publication actually readTHT Shanghai Laigong · homepage ↗

    THT company ownership and advertised precision-bearing focus; not independent audit.

  2. Official actual page and images/jj.jpg viewed in browserLaigong · company/inspection page and image introduction ↗

    2007 founding and production statements; actual inspection captions, not calibrated lot records/current audited capacity.

  3. Official detail updated 20 June 2022THT · actual 70-series spindle-bearing listing ↗

    Full suffix alternatives; not all suffix definitions, current stock or candidate ratings.

  4. Official technical article dated 9 April 2009THT · angular-contact arrangement article ↗

    Listed series, paired/multiple arrangements and load discussion; historical technical publication.

  5. Official original image actually viewed at natural sizeTHT · original bearing-introduction image catalogue ↗

    First-table C/AC angle and grease/oil distinctions, H7005 envelope; current revision/candidate rating not established.

  6. Official actual article dated 9 April 2009THT · cylindrical spindle-support article ↗

    Radial/axial support discussion and title/body series discrepancy; exact candidate needs controlled drawing.

  7. Official actual inventoryTHT · product inventory ↗

    Bearing and spindle categories; not current inventory/availability or scope of every manufacturing process.

  8. Official actual detail dated 20 July 2018THT · CNC-lathe electric spindle detail ↗

    Image/category, blank model/dimensions and zero price field; no usable current specification or quote.

  9. Official actual technical article dated 18 September 2009THT · spindle dynamic-balance article ↗

    Balance background; not candidate assembly test or order approval.

  10. Official actual dedicated contact pageTHT · Shanghai liaison contact ↗

    Liu Chao, phone/email and office role; production/receiving site requires confirmation.

Report a source correction → · Return to inquiry checklist ↑

THT published product scope reviewed

The manufacturer website describes precision machine-tool bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.