BearingIndex
THE BEARINGINDEX DIRECTORY

Youhe

Youhe describes miniature deep-groove bearings and custom ring, shaft and housing assemblies. Define what is included in the supply, then approve clearance, sealing, lubrication and the assembled result.

YOUHE · BEARING OR COMPLETED ASSEMBLY

Define the supplied item before comparing a quote.

Youhe’s website focuses on miniature precision deep-groove bearings in bearing-steel, stainless and flange forms. Its technical page goes further: nonstandard inner/outer rings and matching shafts or housings can be discussed, including supply as an assembled completed item. That changes the drawing, inspection and design responsibility a buyer must agree. Actual product focus [1] Custom and assembly scope [2]

Prepare a sourcing inquiry
01

Choose a loose bearing, modified rings or a completed assembly.

The website lists bearing-steel and stainless materials, open, shielded and sealed forms, metal or nylon cages, flange retention, V-groove stop-ring forms and nonstandard inner/outer rings. These are categories to discuss, not an approved combination for every model. The technical page also describes matching shafts and bearing housings and supplying them assembled. Published variants [1] Actual assembly offer [2]

Loose bearing

Specify complete model/suffix, envelope with units, material, clearance, precision, cage, closure and grease. Define the supplied part’s inspection and your own shaft/housing assembly conditions.

Special inner or outer ring

Provide a controlled drawing for flange, groove or other custom features, including dimensions/tolerances, mating parts and how the ring will be located and loaded. Confirm feasibility and design responsibility before paying for tooling.

Bearing with shaft or housing

List every included component, fits, retention and assembly method. Agree a completed-item drawing and functional acceptance, not only a bearing inspection report. Identify who designs and approves each interface.

The published standards-specification route did not establish a complete model-by-model controlled dimensional/load table in this review. Request the actual offered drawing and ratings; do not invent a product number from the range description. Custom response timing and available quantities must be confirmed directly. Actual specification route [8]

02

State the exposure and starting torque before choosing a closure.

The technical-page summary distinguishes open bearings, shields and seals. It describes an outer-ring-fixed SPCC shield without inner-ring contact, and seal forms that can be contacting or noncontacting. Ask which exact arrangement the offered suffix denotes. Its dated 2 January 2018 seal and grease articles are general guidance, not a present stocked lubrication specification for your model. Actual closure summary [2] Dated seal article [3] Dated grease article [4]

Small motor or low-torque assembly

Provide start/run speed, load, temperature and numerical torque/noise requirements. Obtain the offered seal contact form, grease type and fill and define the temperature and method for sample torque testing. Do not accept “low noise” as a complete acceptance criterion.

Freeze the accepted grease, fill and closure build in the order specification. If Youhe proposes an alternative, compare sample torque, vibration and installed duty under the same conditions before approving the change. These are buyer checks, not performance guarantees inferred from the website.

03

Ask what the two reported full-inspection stages actually measure.

Youhe describes an automated assembly sequence: matching/assembly → full clearance inspection → cleaning → grease and cover operations → full noise inspection. This is useful process information, but the publication does not give an order’s numerical limits, measurement setup, calibration or lot-linked results. A reported 100% inspection stage is not proof that a particular delivered batch passes your specification. Actual published assembly sequence [1]

  1. Before lubrication and closure

    Identify radial-clearance requirement and measurement method, including applied load and units. Ask how the process identifies rejects and retains results or traceability for the accepted lot.

  2. After grease and cover operations

    Agree noise/vibration method, measurement speeds and bands and numerical acceptance. Link the sample and lot report to the actual grease, cage and closure build.

  3. After assembly into the buyer’s item

    Measure agreed torque/runout, temperature and noise in the completed mechanism. Keep shaft/housing fits and assembly settings with the result; a loose-bearing result does not alone approve the assembled item.

The national standards platform lists GB/T 4604.1-2012 for radial internal clearance and GB/T 307.1-2017 for radial-bearing geometrical specifications and tolerances as current; both show a 1 July 2025 review concluding continued validity. Use an agreed applicable standard and edition or controlled drawing when writing the order. These official records identify standard scope and status, not Youhe certification or proof of compliance. They also do not substitute for a separate noise specification. Official clearance record [5] Official tolerances record [6]

No clearance value, noise grade or dimensional tolerance is invented here. The exact model, bore interval and agreed standard/drawing determine what must be measured and accepted.

04

Make the accepted sample reproducible in the next order.

The website states ISO9000 certification in 2017 and an annual review in November 2023. A current issuer certificate, exact edition, covered site and validity were not established. Ask for the required current certificate and annex and verify its issuer record. The stated assembly capacity is a manufacturer claim; it is not a current available slot, delivery promise or independently measured production output. Dated system and capacity wording [1]

What should a sample approval include?

Full supplied-item definition and drawing revision; exact material, clearance, cage, grease and closure; bearing lot and mating-part identification; inspection and installed functional results under agreed conditions. For completed assemblies, include the assembly process and who approves the interfaces.

What must be reconfirmed for a repeat order?

Manufacturing site/route, suppliers and controlled build, lot release and change notification. Agree approval before modifying the rings, shaft/housing fits, lubricant, cage, seals or assembly settings that affected the accepted sample.

The published company address is 1388 Zhenluo East Road, Jiaochuan, Zhenhai, Ningbo, phone 0574-86560699, fax 0574-86653290 and [email protected]. The website states credit code 91330211MA28238F0J. Confirm legal contracting and authorised engineering/sales details directly. The contact page’s 1–2 working-day reply statement is not a production lead time or resolution guarantee. Actual contact page [7]

Request sample/tooling costs, order quantity/MOQ, present delivery and nonconformance handling for the defined item. A single assembled-item quote should explicitly state which bearing, shaft/housing and assembly/testing costs and responsibilities it includes.

YOUR NEXT STEP

Prepare a Youhe bearing or assembly brief

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

0 model records

No documented models yet.

Try broader requirements, or explore the manufacturer’s published product scope.

Explore manufacturers →

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Manufacturer homepage, browser readYouhe · miniature scope and assembly inspection sequence ↗

    Material/form categories, full clearance/noise stage descriptions and dated ISO wording; current output, certification and lot acceptance not inferred.

  2. Manufacturer technical publicationYouhe · technical and custom assembly scope ↗

    Nonstandard rings, shafts/housings and completed assembly offer; closure summary is not a model-specific performance guarantee.

  3. Dated manufacturer guidance, browser readYouhe · seal comparison article ↗

    2 January 2018 article identity; specific offered suffix, current seal build and exposure rating require confirmation.

  4. Dated manufacturer guidanceYouhe · grease guidance article ↗

    2 January 2018 guidance route; no actual order grease brand, fill quantity or temperature rating established.

  5. Primary standards platform, browser readSAMR · radial internal clearance standard ↗

    GB/T 4604.1-2012 current, 1 July 2025 review continued validity; standard scope/status only, not supplier compliance or accreditation.

  6. Primary standards platform, browser readSAMR · radial-bearing GPS and tolerances standard ↗

    GB/T 307.1-2017 current and continued validity; dimensional specification record, not a noise rating or Youhe certificate.

  7. Manufacturer contact publicationYouhe · actual contact page ↗

    Chinese Zhenluo East Road address, phone/fax/email and published credit code; reply wording is not manufacturing delivery.

  8. Manufacturer route checked in browserYouhe · standards-specification route ↗

    A complete controlled model/load table was not established; obtain the offered model drawing rather than inventing numbers from category descriptions.

Report a source correction → · Return to inquiry checklist ↑

Youhe published product scope reviewed

The manufacturer website describes miniature precision ball bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:34

Source documentation retained for editorial review.