BearingIndex
THE BEARINGINDEX DIRECTORY

17TAC47C — 17 × 47 × 15 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 15 mmD = 47 mmd = 17 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Angular contact

17TAC47C

17TAC47C is a angular contact designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 17 × 47 × 15 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
17 mm
Outside D
47 mm
Width B
15 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Can 17TAC47C replace 15TAC47C while keeping the existing screw support?

The published envelopes do not establish that replacement. YJB gives both items a 47 mm outside diameter and 15 mm width, but their bores are 17 mm and 15 mm. Resolve the actual screw-end bearing seat and complete support drawing before treating the shared housing-side dimensions as compatibility.

Two unchanged dimensions leave the shaft interface changed.

YJB’s two actual TAC rows [1] list:

YJB field15TAC47C17TAC47C
Bore d15 mm17 mm
Outside diameter D47 mm47 mm
Width B15 mm15 mm
Approximate catalogue mass0.13 kg0.14 kg

The bore differs by 2 mm in diameter. A support drawing with a 15 mm nominal bearing seat does not describe the same shaft interface as the 17 mm nominal bore. Matching the housing diameter and nominal width therefore leaves a material interface question unresolved.

Identify the bearing journal on the actual screw-end drawing, rather than using the screw’s overall diameter or the old support’s outside dimensions. Include the shaft shoulder, locknut/spacer arrangement and axial locating faces in the retrofit review. The three envelope dimensions contain no approved sleeve, journal modification or retention scheme.

If a replacement screw or support is part of the proposal, obtain the coordinated assembly drawing identifying every retained and changed interface. If only the bearing is being replaced, retain the old complete designation and have the manufacturer assess compatibility. This dimensional comparison does not authorize machining or modifying the existing screw.

The 17TAC47C model PDF includes series section and mounting illustrations [2]. They do not give numerical shoulder bounds or identify a matched retrofit set. For the separate pairing and unnamed-field problem in the 15 mm item, see the individually reviewed 15TAC47C page.

A larger bore and repeated catalogue fields do not demonstrate higher capacity.

Both actual rows display 27 under Cor, 11.5 under the maximum-axial-load heading and the same “21.527” string under Cr. The Cr column elsewhere in the series also contains strings such as “28.541.5”. Ask YJB for the intended numeric value and a controlled rating specification; do not split a string into a guessed number or use it as a verified calculation input.

The official 17TAC47C PDF [2] repeats “21.527”. The download does not independently resolve that formatting question. It also repeats 12000 under grease lubrication without a speed unit and the two fields labelled only “(KN)” and “(N.mm)”, with values 2.6 and 50.

The larger bore and 0.01 kg catalogue-mass difference supply no stiffness, working-force or life improvement for the proposed support. The maximum-axial field is not a documented continuous operating allowance for your machine, and the unit-only fields are not identified preload or locknut torque instructions.

After the interface drawing is resolved, submit the actual axial force cases and reversals, bearing count/orientation, lubrication and rotational duty for the selected arrangement. The required evidence is the coordinated support specification and manufacturer assessment, rather than a capacity conclusion drawn from the bore number or an unclear Cr field.

What each manufacturer published.

ManufacturerCr column — value needs clarificationStatic load rating (kN)Grease column — unit unconfirmedReference mass (kg)Source recorded
YJB
17TAC47C
21.527
The source displays 21.527 under Cr. Other TAC rows contain malformed-looking numeric strings; obtain the intended value before using it in a calculation.
2712000
The examined website and model PDF label this field grease lubrication but give no speed unit. Historical rpm interpretation awaits confirmation.
0.142026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 215 mm
Mean diameter dm(D + d) / 232 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 17TAC47C.

YJB

Hangzhou, Zhejiang, China

Precision spindle and machine-tool bearings

YJB publishes precision angular-contact, double-row cylindrical roller and ball-screw bearing ranges. Its NN3006-K-W33 catalogue separates bearing dimensions from mounting callouts. Confirm the offered bore, precision and lubrication configuration against the actual spindle drawing.

Published ranges: Angular contact ball bearings · Cylindrical roller bearings · Double-direction thrust angular contact bearings · Tapered roller and nonstandard designs

740 designations documented here · 1 reviewed evidence record · source recorded 2026-10-07

Ask YJB about 17TAC47C

Applications the publishing works state.

ApplicationStated by
Instrument motorsYJB
Machine-tool spindlesYJB
Medical equipmentYJB
RoboticsYJB

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 17x47x15 mm envelope.

DesignationBearing familyWorks
BS1747Angular contact1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Request a quote for 17TAC47C.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YJB · 17TAC47C source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YJB · actual 15TAC47C / 17TAC47C series rows ↗

    Fresh model rows and complete headers read; dimensions/mass and unresolved raw field strings retained. Other malformed-looking Cr cells give a reason to request clarification, not evidence for any guessed correction.

  2. YJB · official 17TAC47C model PDF ↗

    Downloaded one-page official PDF, text extracted and native browser rendering viewed at 100%. Numeric strings, unnamed fields and series illustrations checked, not a controlled retrofit drawing.

  3. YJB · exact 17TAC47C detail ↗

    Fresh exact detail read, confirming 17/47/15 mm, approximate 0.14 kg and the same unresolved raw fields. No fitted screw, modified seat or tested support supplied.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.