BearingIndex
THE BEARINGINDEX DIRECTORY

20TAC47C — 20 × 47 × 15 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 15 mmD = 47 mmd = 20 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Angular contact

20TAC47C

20TAC47C is a angular contact designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 20 × 47 × 15 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
20 mm
Outside D
47 mm
Width B
15 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Does changing from 17TAC47C to 20TAC47C support a higher axial-force requirement?

YJB’s examined maximum-axial entries do not show that improvement: 20TAC47C is listed at 10.6 kN and 17TAC47C at 11.5 kN. Bore size is not a substitute for the actual catalogue field, and that field still needs its conditions defined for the proposed screw support.

The 20 mm-bore item has the lower published maximum-axial entry.

YJB’s actual adjacent catalogue rows [1] share D = 47 mm and B = 15 mm. In the explicitly labelled maximum-axial-load column:

YJB itemBoreMaximum-axial entry
17TAC47C17 mm11.5 kN
20TAC47C20 mm10.6 kN

The latter entry is 0.9 kN lower. This is a comparison of two labelled source fields, not a calculation of either support’s working capacity, stiffness or life. A larger bore therefore cannot be used as evidence of an axial-capacity upgrade from these rows.

For a conditional numerical screen, a requirement of 11 kN would exceed 20TAC47C’s published 10.6 kN entry. This is not an observed machine load. The examined row would not support that requirement without further manufacturer evidence. The same number being below 17TAC47C’s entry would not, by itself, approve the other item for continuous duty.

Ask YJB what the maximum-axial entry represents: the construction and arrangement to which it applies, the loading conditions and any duty restrictions. Do not assume it is an interchangeable single-bearing, paired-set and complete-machine allowance. The examined row does not identify those conditions.

Resolve the force cases and field meanings before calling the support upgraded.

Provide the actual screw-end axial forces in each direction, including the relevant peak, reversing and continuous cases, alongside the support drawing and bearing arrangement. Request the manufacturer’s assessment for the exact offered construction, not a recommendation based only on a 20 mm bore.

The official 20TAC47C PDF [2] confirms 20 / 47 / 15 mm and repeats the 10.6 kN field. It shows a series section and single/paired mounting illustrations but no model-specific support stiffness or machine positioning result. A selected set and a controlled drawing are still required.

The PDF and website also display “19.325” under Cr. Other series Cr cells contain strings such as “28.541.5”, so the intended numeric formatting needs YJB’s confirmation. This page keeps the raw field and excludes it from the shared load-ratio calculation; it does not guess a corrected rating.

The remaining unresolved entries matter to this request: 12000 has no speed unit under the grease heading, 2.3 has only a kN label, and 50 has only an N·mm label. They do not establish an operating speed, a preload setting or a locknut tightening instruction. Obtain their definitions rather than using them to complete a support specification.

If the proposed change is a retrofit, the larger bore also changes the shaft interface. The 17TAC47C interface review explains why shared housing-side dimensions do not establish compatibility. Resolve that drawing question separately from the force assessment; neither one proves the other.

What each manufacturer published.

ManufacturerCr column — value needs clarificationStatic load rating (kN)Grease column — unit unconfirmedReference mass (kg)Source recorded
YJB
20TAC47C
19.325
The source displays 19.325 under Cr; the series contains malformed-looking numeric strings. Confirm the intended rating before using this field in a calculation.
2512000
The examined website and official PDF give 12000 under grease lubrication without a speed unit. Historical rpm interpretation remains unconfirmed.
0.132026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 213.5 mm
Mean diameter dm(D + d) / 233.5 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 20TAC47C.

YJB

Hangzhou, Zhejiang, China

Precision spindle and machine-tool bearings

YJB publishes precision angular-contact, double-row cylindrical roller and ball-screw bearing ranges. Its NN3006-K-W33 catalogue separates bearing dimensions from mounting callouts. Confirm the offered bore, precision and lubrication configuration against the actual spindle drawing.

Published ranges: Angular contact ball bearings · Cylindrical roller bearings · Double-direction thrust angular contact bearings · Tapered roller and nonstandard designs

740 designations documented here · 1 reviewed evidence record · source recorded 2026-10-07

Ask YJB about 20TAC47C

Applications the publishing works state.

ApplicationStated by
Instrument motorsYJB
Machine-tool spindlesYJB
Medical equipmentYJB
RoboticsYJB

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 20x47x15 mm envelope.

DesignationBearing familyWorks
BS2047Angular contact1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Request a quote for 20TAC47C.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YJB · 20TAC47C source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YJB · actual 17TAC47C and 20TAC47C catalogue rows ↗

    Fresh rows and full headers read: independent maximum-axial column, actual bore/OD/width and unresolved numeric/unit-only fields. Lower maximum-axial entry is not a tested support comparison.

  2. YJB · official 20TAC47C PDF ↗

    Grounded download link opened; one-page official PDF downloaded and text read. Native browser rendering at 100% actually viewed with the 20/47/15, 10.6 and unresolved field entries. Illustrations are series material, not a controlled matched-support specification.

  3. YJB · exact 20TAC47C detail ↗

    Fresh detail read: repeats the model-specific envelope and field values. No working machine, continuous-duty force limit, stiffness test or positioning result inspected.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.