BearingIndex
THE BEARINGINDEX DIRECTORY

FR133 — 2.38 × 4.762 × 1.588 mm

BOUNDARY DIMENSIONSUNIT / mm

The recorded 2.38 × 4.762 × 1.588 mm tuple matches Hongchi’s open-version row. It does not describe the complete flange envelope: the flange outside diameter is 5.944 mm. Hongchi’s ZZ version is 2.38 mm wide and has a 0.787 mm flange thickness, rather than the OPEN row’s 1.588 and 0.457 mm. Select the configuration before using an axial stack drawing.

Deep groove ball

FR133

FR133 is a deep groove ball designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 2.38 × 4.762 × 1.588 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
2.38 mm
Outside D
4.762 mm
Width B
1.588 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Adding ZZ to an FR133 order changes two axial dimensions.

Hongchi’s FR133 table gives the open and ZZ versions the same 2.380 mm bore, 4.762 mm body diameter and 5.944 mm flange diameter. Their bearing width and flange thickness differ. A replacement selected only by bore and body diameter can therefore leave the retaining face, cover or spacer in the wrong position. Use the selected row and the flange sketch together before changing the closure.

The ZZ row is 0.792 mm wider, with a flange 0.330 mm thicker.

The actual Hongchi FR133 table [1] distinguishes the OPEN and zz rows for both width and flange width. It does not give one universal FR133 axial size. The old directory width below belongs to the OPEN row.

FR133 dimension, mmOPEN rowZZ row
Bore / body outside diameter2.380 / 4.7622.380 / 4.762
Flange outside diameter5.9445.944
Bearing width1.5882.38
Flange thickness0.4570.787

Subtracting the published nominal entries gives a bearing-width increase of 0.792 mm and a flange-thickness increase of 0.330 mm. These are calculations from the table, not measured spare clearance, tolerance allowances or instructions to remove that amount from a spacer. The two changes affect different callouts and should stay separate on the mounting drawing.

Hongchi’s linked section illustration [2] shows the flange on the left-hand arrangement, with body diameter D, larger flange diameter D1, total width B/C and flange thickness C2. For an existing open-version installation, mark the face against which the flange seats and the positions of the shaft shoulder, spacer and cover. Ask Hongchi to return the ZZ drawing against those same datums. That review can establish which faces move and whether the selected configuration fits the available axial space; comparing only the shaft and body diameters cannot.

RS/RZ needs its own geometry. The product-name line mentions zz/rs/rz/open, but the examined width and flange-width entries distinguish only OPEN and zz. A rubber-closure proposal cannot inherit the ZZ width or flange thickness merely because it appears in the same title. Require its selected drawing before approving the original stack.

State the actual closure and lubricant requirement in the order. The page’s shared speed block gives grease 80 and “润滑剂” 95 under ×1000 rpm; it does not identify a separate limit for each closure, and “润滑剂” is not an explicit oil-bath specification. Its material-options line also lists several materials while the detailed ring/ball rows name GCr15. Resolve the offered material and operating conditions with Hongchi rather than treating a shield or a generic options list as proof of a stainless, high-speed or sealed configuration.

A 4.762 mm body seat does not describe the 5.944 mm flange space.

Hongchi gives this FR133 a body outside diameter of 4.762 mm and flange outside diameter of 5.944 mm. Use the smaller dimension for identifying the body envelope and the larger one when marking the flange space on the surrounding part. Neither value supplies the housing fit, flange-face tolerance or corner detail needed to release a machining drawing.

The illustration contains two different retaining arrangements. On the left, C2 is explicitly labelled flange width. On the right, the same C2 notation is labelled snap-ring position, with a separate snap-ring outside diameter D2. The right-hand drawing does not establish that FR133 is supplied with a snap ring, and its C2 position cannot replace the FR133 table’s 0.457/0.787 mm flange-thickness entries. Keep the actual flange arrangement and its callouts on the request.

Quotation or drawing entryWhat the actual source givesDecision before ordering
Hongchi FR133A separate flange diameter 5.944 mm and OPEN/ZZ flange-thickness rows.Specify the selected closure and show where the flange locates, including its contact face and surrounding clearance.
Hongchi R133zzThe separate deep-groove page repeats bore 2.380, body OD 4.762 and OPEN/ZZ widths 1.588/2.380 mm. It has no matching FR133 flange-dimension rows.A quote shortened to R133zz leaves the required flange unresolved. Ask for the offered part drawing; the matching three dimensions do not approve substitution.
Shared illustration, right sideD2 is a snap-ring diameter and C2 a snap-ring position.Do not add a snap ring to the FR133 order or copy that position into the flange-thickness field.

The separate R133zz page [3] is useful for detecting that shortened quotation, not for authorizing removal of the locating flange. Both product pages also repeat the same 144 N dynamic and 53 N static entries. Equal catalogue load figures cannot settle the missing flange, its fit or the way this small assembly locates.

For sample acceptance, first identify the ordered OPEN or ZZ version and the exact manufacturer drawing revision. Compare the sample’s bearing-body width, flange diameter, flange thickness and locating face with that drawing and the existing assembly. Ask the supplier to state the applicable tolerances rather than inventing them from the three-decimal catalogue entries. The linked product photograph [4] shows several open and covered flanged bearings without a scale or individual model identification; it cannot verify the ordered sample’s dimensions or supplied closure.

Hongchi’s table footnote calls its data reference information and names “宏诚精密”, whereas the website footer names Ningbo Hongchi. The page alone does not establish the relationship between those names. Have the responding manufacturer identify the legal supplier and the drawing it is offering together with the exact FR133 configuration. That keeps the interface approval attached to an identifiable part and quotation.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Open-version bearing width (mm)Source recorded
Hongchi
FR133
2.384.7621.588
This historical 1.588 mm width matches Hongchi’s OPEN row. Its ZZ row gives 2.38 mm bearing width and a different flange thickness; the page does not give separate RS/RZ geometry.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish FR133.

Hongchi

Ningbo, Zhejiang, China

Miniature metric, inch and thrust bearings

Hongchi’s FR188 table gives different bearing and flange widths for open and ZZ versions, while 6800 and 63800 share bore/OD but differ in width. Use those distinctions to prepare a controlled interface drawing; qualify U/V wheels against the actual rail section and obtain part-linked manufacturing and inspection documents where the website’s technical text names other companies.

Published ranges: Metric and inch miniature bearings · Flanged miniature bearings · Flat thrust ball bearings

80 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Hongchi about FR133

Applications the publishing works state.

ApplicationStated by
Cooling fansHongchi
DronesHongchi
Miniature motorsHongchi
Precision instrumentsHongchi

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for FR133.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Hongchi · FR133 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Hongchi · exact FR133 product table ↗

    Exact official page actually read: OPEN/ZZ flange diameter, bearing width and flange thickness; shared material/load/speed text and reference-data footnote. No separate RS/RZ geometry, interface tolerance or closure-specific speed is inferred.

  2. Hongchi · linked flange and snap-ring section ↗

    Original 715×478 illustration actually viewed. The left flange arrangement labels D1 and flange width C2; the right snap-ring arrangement labels D2 and snap-ring position C2. It is not a controlled FR133 manufacturing drawing.

  3. Hongchi · separate R133zz product table ↗

    Separate official deep-groove entry actually read: repeats the bore, body OD and OPEN/ZZ bearing widths, without the FR133 flange-dimension rows. Used to identify an unresolved shortened quote, not to approve interchange.

  4. Hongchi · linked flanged-bearing photograph ↗

    Original photograph actually viewed: several open and covered flanged bearings, without scale or individual model identification. Not dimensional or supplied-configuration evidence.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.