BearingIndex
THE BEARINGINDEX DIRECTORY

LM10UU-OP — 10 × 19 × 29 mm

BOUNDARY DIMENSIONSUNIT / mm

YTP’s LM10UU-OP is an open linear bearing: the series end view labels opening angle θ and height h1, while the longitudinal view separates overall length L from retaining-groove spacing B. The exact row lists θ 80°, h1 6.8, L 29 and B 22. A 10×19×29 mm envelope does not describe these interfaces.

Linear bearings

LM10UU-OP

LM10UU-OP is a linear bearings designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 10 × 19 × 29 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
10 mm
Outside D
19 mm
Length L
29 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Fit the 80° opening and retaining grooves before approving a 10×19×29 replacement.

YTP lists LM10UU-OP with a 10 mm bore, 19 mm outside diameter and 29 mm overall length. Its open section also has an 80° angle and h1 reference of 6.8; the retaining-groove spacing B is 22, rather than the overall length. These interfaces, its three ball rows and the supplier’s kgf load entries need their own checks when replacing a linear bearing around an existing shaft and support.

The 80° opening and B22 grooves are separate from the 29 mm length.

YTP’s exact LM10UU-OP row [1] and its two series CAD views describe different parts of the interface. Check them against the actual shaft, support and retention drawing. The opening view labels θ and h1; it does not supply a complete installation clearance or prove that an existing support passes through the bearing over its full travel.

InterfaceExact catalogue entryBuyer check
Bore dr / outside D10 / 19 mmdr: 0/−0.009; D: 0/−0.013. Keep each dimension’s own tolerance with the selected drawing.
Overall length L29 mm; tolerance 0/−0.20.Use L for the overall axial envelope. B22 is a different interface.
Retaining grooves B / D1 / W22 / 18 / 1.3; B tolerance 0/−0.20.The longitudinal view marks B between the grooves, D1 at the groove diameter and W at each groove. Obtain the controlled groove and ring specification.
Opening θ / h180° / 6.8Match the end-view labels to the mating support; obtain the height datum, tolerances and required clearance.

The size filters explicitly label dr, D and L in mm. The auxiliary columns show the symbols and numbers above without independently printing a unit beside each; obtain the controlled drawing’s units before machining the grooves or support. The series images establish the labelled features, while a selected drawing must define the actual manufacturing and assembly limits.

The longitudinal CAD view [2] depicts a W groove at each end. Do not use (29−22)/2 as a released end-to-groove machining dimension: the drawing’s groove boundaries and datums matter. Likewise, the end view’s h1 and 80° angle describe the opening, rather than a complete support-clearance calculation.

The same catalogue lists LM20UU-OP with a 60° opening and four ball rows, compared with LM10UU-OP’s 80° and three rows. An opening rule copied across the series would change the support interface. Keep the exact LM10 row and opening view [3] with the enquiry, and have YTP mark the intended support position and force directions on the assembly drawing.

38/56 kgf and a resin-cage UU row need precise ordering language.

The exact table states three ball rows, mass 23 g, basic load C 38 kgf and Co 56 kgf. Mass and load are different quantities: these load figures are force entries, not a declaration that a carriage can carry a 38 or 56 kg payload in any direction. YTP does not provide a selected support-orientation correction, duty calculation or measured installed accuracy in this row.

For a side load or a force directed toward the opening, send the assembly’s force directions and support orientation to YTP. Ask which conditions and directional assessment apply to these three ball rows, then assess the complete guide arrangement. Do not divide a nominal payload equally among bearings without an assembly assessment, or treat the table’s radial-runout maximum of 0.012 as carriage positioning accuracy.

Series material row [1]Published distinctionOrdering consequence
LM □ UU-OPGCr15 shell and balls; resin cage; 65Mn seal skeleton and nitrile rubber.Confirm this complete configuration on the offered LM10UU-OP and its material documentation.
LM □ M-OP304 stainless cage; rubber column shows a dash.A stainless cage does not turn the listed GCr15 shell and balls into an all-stainless bearing, or establish the UU sealing configuration.

The UU-OP row gives shell hardness 60–64 HRC and ball hardness 61–66 HRC. Its −20 to 80°C entry sits under the cage “operating temperature” heading; the M-OP row shows −20 to 150°C there. Do not give LM10UU-OP the M-row temperature range, or call either column a tested whole-machine operating range. Supply the actual temperature, lubricant and contamination conditions for the offered cage and seal assessment.

YTP’s comparison columns associate this row with YHDA LMC31-d10, NB SM10GUU-OP and SAMICK LM10UU-OP. Those are YTP’s published reference entries; this page has not established the other brands’ current groove dimensions, opening geometry, loads or sealing configuration. Use them to identify candidate documents, then compare each proposed part’s controlled drawing before substitution. Keep the offered manufacturer and complete designation on the order.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Reference mass (kg)Overall length L (mm)Source recorded
YTP
LM10UU-OP
10190.023292026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish LM10UU-OP.

YTP

Ningbo, Zhejiang, China

Linear ball bearings and support units

YTP offers a linear-motion catalogue, cross-reference table and selection interface. The LM20UU/MX length difference and explicit reference-only MX sizes show why a replacement needs full interfaces and availability confirmation; qualify the shaft, alignment, load distribution and lubrication together, then reconcile calculation assumptions and applicable standard editions.

Published ranges: Standard and flanged linear ball bearings · Nickel-plated and steel-cage variants · Boxed linear-bearing units · KH drawn-cup linear bearings

287 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask YTP about LM10UU-OP

Applications the publishing works state.

ApplicationStated by
Linear-motion systemsYTP

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for LM10UU-OP.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YTP · LM10UU-OP source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YTP · LM10UU-OP exact row and series material table ↗

    Exact LM10UU-OP: three ball rows, 23 g, dr10/D19/L29, tolerance entries, B22/D1 18/W1.3/h1 6.8/θ80°, radial-runout maximum 0.012 and C38/Co56 kgf. Series material headings separate UU resin/nitrile from M variants. Catalogue size filters identify the three main dimensions in mm; auxiliary machining units require a controlled drawing.

  2. YTP · Open-series longitudinal CAD view ↗

    YTP’s catalogue-linked series section distinguishes L, groove spacing B, groove diameter D1 and W at both ends. It provides no selected machining release or retaining-ring specification.

  3. YTP · Open-series end CAD view ↗

    YTP’s catalogue-linked end view labels dr, θ and h1. Use it with the exact LM10 row and the controlled mating-support drawing; it does not establish installed clearance or directional load factors.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.