BearingIndex
THE BEARINGINDEX DIRECTORY

LM30 — 30 × 45 × 64 mm

BOUNDARY DIMENSIONSUNIT / mm
L = 64 mmD = 45 mmd = 30 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Linear bearings

LM30

LM30 is a linear bearings designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 30 × 45 × 64 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
30 mm
Outside D
45 mm
Length L
64 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-30

Does an LM30M stainless-steel cage make the whole bearing stainless?

No. YTP’s construction table assigns 304 stainless steel to the LM M cage, while listing GCr15 for its shell and balls. LM30, LM30UU and LM30M share a nominal 30 × 45 × 64 mm envelope, but their cage and sealing descriptions are not interchangeable.

YTP prints the load ratings in kgf, and the variants are not all the same.

YTP’s LM30 tables [1] list the ball rows, mass and basic load ratings with each designation. The ratings are printed in kgf.

YTP designationBall rowsLength LMassC (kgf)Co (kgf)
LM30, LM30UU, LM30M664 mm250 g160220
LM30UU-OP (open type) [5]564 mm210 g160220
LM30LUU (long type) [6]6123 mm480 g254560

If your calculation works in newtons, convert with 1 kgf = 9.80665 N: 160 kgf is about 1,569 N and 220 kgf about 2,157 N. That is arithmetic on YTP’s figures, not a value YTP prints.

The open type keeps the ratings but loses a ball row

LM30UU-OP is cut open for a supported shaft and carries 5 ball rows instead of 6, yet YTP prints the same 160 / 220 kgf for it. Ask YTP which load direction those ratings assume for the open type before you orient the opening in your housing.

YTP’s cross-reference is YTP’s claim

YTP’s LM30UU page [7] lists MISUMI LMU30, NB SM30GUU and SAMICK LM30UU alongside its own part. That is YTP’s cross-reference. Those makers publish their own ratings, which need not match YTP’s; compare an offer with the ratings of the maker who supplies it.

Read each component column before accepting ‘stainless’ on a quote.

YTP’s actual construction table [2] separates shell, balls, cage and sealing parts. For LM M it lists GCr15 for shell and balls and 304 stainless steel for the cage. The unsealed LM and sealed LM UU entries use resin cages. A cage description cannot be extended to the other components.

YTP lists SLM constructions separately, with different shell and ball material entries. That is evidence that a whole-bearing material choice is a separate designation, not permission to rename LM30M as an SLM item. If corrosion resistance is the purchase requirement, obtain the complete selected SLM designation, its own dimensional row and its material statement.

Tell the supplier which exposure matters—water, a cleaning agent or another specified medium—and request qualification for that actual construction. The LM30M cage column does not establish chemical compatibility, corrosion performance or a washdown rating.

If the old part is LM30UU, an unsealed LM30 changes the requirement.

The LM30 source route [1] is explicitly the standard unsealed family. In the construction table, LM UU has nitrile rubber in the seal-material column; LM and LM M show no rubber there. Do not remove UU from an old marking when preparing a replacement request.

If keeping the existing sealed arrangement, ask for the complete offered sealed designation and the closure drawing. If considering unsealed LM30 or LM30M, the supplier and assembly owner must address how the axis will manage lubricant and contamination with that change. Matching the nominal envelope does not answer it.

YTP’s maintenance guidance [4] distinguishes oil and grease routes. That background does not select the lubricant or replenishment method for the replacement you have not yet identified. Preserve the actual seal and housing arrangement in that discussion.

The shared envelope still leaves a groove check to perform.

The examined LM30 row gives dr = 30 mm, D = 45 mm and L = 64 mm. Its external stopping-groove fields are B = 44.5 mm, D1 = 43 mm and W = 1.85 mm. B is not the total length of this linear bearing. Keep those symbols on the controlled drawing when checking the old retaining parts.

The UU table lists LM30UU / LM30M together at the same nominal envelope and groove fields. That supports a drawing comparison, not automatic approval of every seal and material variant. Request confirmation of the offered part’s tolerances and retention details before reusing the housing.

The LM30 row’s mass is 250 g and its C/C0 headings are kgf, with values 160/220. Neither a material selection nor a seal suffix converts those into an axis payload. YTP’s fixing guidance [3] also warns about alignment and direct set-screw pressure on the outer shell; the selected housing arrangement must address those conditions rather than relying on the nominal 45 mm outside diameter.

What each manufacturer published.

ManufacturerReference mass (kg)Source recorded
YTP
LM30
The stored record keeps dimensions and mass only. YTP’s current LM30 row also prints 6 ball rows and basic load ratings C 160 kgf / Co 220 kgf; kgf is YTP’s own unit, not converted in the directory table.
0.252026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 27.5 mm
Mean diameter dm(D + d) / 237.5 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish LM30.

YTP

Ningbo, Zhejiang, China

Linear ball bearings and support units

YTP offers a linear-motion catalogue, cross-reference table and selection interface. The LM20UU/MX length difference and explicit reference-only MX sizes show why a replacement needs full interfaces and availability confirmation; qualify the shaft, alignment, load distribution and lubrication together, then reconcile calculation assumptions and applicable standard editions.

Published ranges: Standard and flanged linear ball bearings · Nickel-plated and steel-cage variants · Boxed linear-bearing units · KH drawn-cup linear bearings

287 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask YTP about LM30

Applications the publishing works state.

ApplicationStated by
Linear-motion systemsYTP

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
LM30L—Linear bearings1
LM30LUU—Linear bearings2
LM30M—Linear bearings1
LM30UU—Linear bearings1
LM30UU-AJ—Linear bearings1
LM30UU-OP—Linear bearings1

Each envelope shown is that designation’s own published size.

Request a quote for LM30.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YTP · LM30 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YTP · LM standard unsealed route, actual LM30 row ↗

    Browser-rendered model row, dr/D/L and groove fields/tolerances, 250 g and kgf columns. Publisher HTTP catalogue read; HTTPS certificate mismatch not bypassed.

  2. YTP · LM UU standard table and construction variants ↗

    Browser-rendered LM30UU/LM30M nominal envelope and separate cage/seal construction. Not an interchange approval.

  3. YTP · clearance selection and fixing ↗

    Published 2023 guidance: mating parts, alignment and outer-ring retention; confirm current selected-variant instructions.

  4. YTP · installation and maintenance ↗

    Published 2023 guidance: lubrication route, alignment and ordinary linear-bearing duty limitation. No universal lubricant grade or life applied.

  5. YTP · LM UU-OP open-type table ↗

    LM30UU-OP row from the table’s own data request: 5 ball rows, 210 g, d30/D45/L64 mm, h1 15, θ 50°, C 160 / Co 220 kgf. Read 2026-10-30.

  6. YTP · LM LUU long-type table ↗

    LM30LUU / LM30LM row: 6 ball rows, 480 g, d30/D45/L123 mm, B 89 mm, C 254 / Co 560 kgf. Read 2026-10-30.

  7. YTP · LM30UU model page with cross-reference ↗

    LM30UU / LM30M row (6 ball rows, 250 g, C 160 / Co 220 kgf) and YTP’s own cross-reference to MISUMI LMU30, YHDA LMC02-d30, NB SM30GUU and SAMICK LM30UU. Read 2026-10-30.

Guide checked 2026-10-30. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.