BearingIndex
THE BEARINGINDEX DIRECTORY

LM40 — 40 × 60 × 80 mm

BOUNDARY DIMENSIONSUNIT / mm
L = 80 mmD = 60 mmd = 40 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Linear bearings

LM40

LM40 is a linear bearings designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 40 × 60 × 80 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
40 mm
Outside D
60 mm
Length L
80 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-30

How much load does an LM40UU carry, and which LM40 is it?

YTP prints C 220 kgf and Co 410 kgf for LM40, LM40UU and LM40M alike: one 40 × 60 × 80 mm envelope with 6 ball rows. The suffix changes the seal and the cage, and with them the temperature range. The open type drops a ball row; the long type changes the ratings.

Five YTP tables carry an LM40 row. Three ratings are identical.

YTP publishes each LM construction in its own table. Read through the tables’ own data requests on 2026-10-30, the LM40 rows are:

YTP designationBall rowsLength LMassC (kgf)Co (kgf)
LM40, LM40UU, LM40M [1–3]680 mm585 g220410
LM40UU-OP, LM40M-OP (open) [4]580 mm500 g220410
LM40L, LM40LUU, LM40LM (long) [5]6151 mm1,170 g350820

In newtons, using 1 kgf = 9.80665 N: 220 kgf is about 2,157 N, 410 kgf about 4,021 N, 350 kgf about 3,432 N and 820 kgf about 8,041 N. That is arithmetic on YTP’s figures, not a value YTP prints.

The open type has one row fewer and the same printed ratings

The -OP rows give an opening of h1 = 20 mm and θ = 50°, 5 ball rows and 500 g, but repeat 220 / 410 kgf. Before orienting the opening in your housing, ask YTP which load direction those ratings assume for the open type.

The long type is not two LM40s

The 151 mm long type is rated 350 / 820 kgf, not double the single bearing’s 220 / 410 kgf. If your design replaces two LM40UU with one LM40LUU, or the reverse, recalculate from the row of the part you will fit.

The bore tolerance and retaining grooves.

The same five tables print the tolerances and the external retaining-ring groove. The 80 mm types share one set of figures; the long type has wider limits.

YTP fieldLM40, LM40UU, LM40M, -OPLM40L, LM40LUU, LM40LM
Inscribed bore dr40 mm, 0 / −0.01240 mm, 0 / −0.015
Outside diameter D60 mm, 0 / −0.01960 mm, 0 / −0.022
Length L80 mm, 0 / −0.30151 mm, 0 / −0.40
Groove spacing B60.5 mm, 0 / −0.30121 mm, 0 / −0.40
Groove diameter D1 / width W57 mm / 2.1 mm57 mm / 2.1 mm
Radial runout, max0.02 mm0.025 mm

B is the distance between the retaining-ring grooves, not the overall length. The bore limits put the inscribed diameter between 39.988 and 40.000 mm for the 80 mm types; the running clearance still depends on your shaft’s own tolerance. YTP’s clearance and fixing guidance [7] covers how the shaft fit is chosen. This page does not choose it for you.

UU and M change the seal, the cage and the temperature range.

YTP’s construction table [2] lists GCr15 steel for the shell (60–64 HRC) and the balls (61–66 HRC) in all three, with GB/T 16940-2012 as the production standard. The differences are:

ConstructionCageSeal rubberOperating temperature
LM40 (unsealed)ResinNone−20 to 80 °C
LM40UUResinNitrile−20 to 80 °C
LM40M304 stainless steelNone−20 to 150 °C

LM40M is not a stainless bearing: only the cage is stainless. YTP lists its stainless SLM series separately. If the old part is marked UU, an unsealed LM40 or LM40M changes how the axis keeps out dirt and holds lubricant; settle that before accepting either as a substitute.

YTP’s cross-reference is YTP’s claim

YTP’s LM40UU page [6] lists MISUMI LMU40, YHDA LMC02-d40, NB SM40GUU and SAMICK LM40UU against its part. Those makers publish their own ratings, which need not match YTP’s. Compare an offer with the ratings of the maker who supplies it.

The rows come from 宁波宇通轴承有限公司 (Ningbo Yutong Bearing Co., Ltd., brand YTP), whose site gives its address as 376 Longzhen Avenue, Longshan Town, Cixi, Ningbo, Zhejiang. Its company page says it runs an ISO 9001:2015 quality system and helped draft GB/T 19673.2-2025, GB/T 27557-2026 and GB/T 27558-2026. No certificate number is shown, so ask for the current certificate with your quotation.

What each manufacturer published.

ManufacturerReference mass (kg)Source recorded
YTP
LM40
The stored record keeps dimensions and mass only. YTP’s current LM40 row also prints 6 ball rows, a 0.02 mm maximum radial runout and basic load ratings C 220 kgf / Co 410 kgf.
0.585
YTP prints 585 g in a column headed (g). Shown here converted to kg.
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 210 mm
Mean diameter dm(D + d) / 250 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish LM40.

YTP

Ningbo, Zhejiang, China

Linear ball bearings and support units

YTP offers a linear-motion catalogue, cross-reference table and selection interface. The LM20UU/MX length difference and explicit reference-only MX sizes show why a replacement needs full interfaces and availability confirmation; qualify the shaft, alignment, load distribution and lubrication together, then reconcile calculation assumptions and applicable standard editions.

Published ranges: Standard and flanged linear ball bearings · Nickel-plated and steel-cage variants · Boxed linear-bearing units · KH drawn-cup linear bearings

287 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask YTP about LM40

Applications the publishing works state.

ApplicationStated by
Linear-motion systemsYTP

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
LM40L—Linear bearings1
LM40LUU—Linear bearings2
LM40UU—Linear bearings1
LM40UU-AJ—Linear bearings1
LM40UU-OP—Linear bearings1

Each envelope shown is that designation’s own published size.

Request a quote for LM40.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. YTP · LM40 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. YTP · LM unsealed table (宁波宇通轴承有限公司) ↗

    LM40 row from the table’s own data request: 6 ball rows, 585 g, dr 40 0/−0.012, D 60 0/−0.019, L 80 0/−0.30, B 60.5, D1 57, W 2.1, runout 0.02, C 220 / Co 410 kgf. Read 2026-10-30.

  2. YTP · LM UU table and construction table ↗

    LM40UU / LM40M row (same values as LM40); construction table: GCr15 shell 60–64 HRC and balls 61–66 HRC, resin or 304 cage, nitrile seal for UU, −20–80 °C (resin) and −20–150 °C (M), GB/T16940-2012. Read 2026-10-30.

  3. YTP · LM M steel-cage table ↗

    LM40M row: 6 ball rows, 585 g, C 220 / Co 410 kgf. Read 2026-10-30.

  4. YTP · LM UU-OP and LM M-OP open-type tables ↗

    LM40UU-OP row (and LM40M-OP in table 243): 5 ball rows, 500 g, h1 20 mm, θ 50°, C 220 / Co 410 kgf. Read 2026-10-30.

  5. YTP · LM LUU long-type table ↗

    LM40LUU / LM40LM row (and LM40L in table 375): 6 ball rows, 1170 g, dr 0/−0.015, D 0/−0.022, L 151 0/−0.40, B 121, runout 0.025, C 350 / Co 820 kgf. Read 2026-10-30.

  6. YTP · LM40UU model page with cross-reference ↗

    LM40UU / LM40M row and YTP’s cross-reference to MISUMI LMU40, YHDA LMC02-d40, NB SM40GUU and SAMICK LM40UU. Read 2026-10-30.

  7. YTP · clearance selection and fixing ↗

    General guidance on shaft fit, alignment and outer-ring retention. Not a fit selected for this page. Read 2026-10-30.

  8. YTP · company introduction ↗

    Product range, ISO 9001-2015 statement without certificate number, standards-drafting statement and address 浙江宁波慈溪市龙山镇龙镇大道376号. The product-catalogue footer prints an older address, 龙山镇西门外工业区. Read 2026-10-30.

Guide checked 2026-10-30. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.