BearingIndex
THE BEARINGINDEX DIRECTORY

SG20 — 6 × 24 × 11 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 11 mmD = 24 mmd = 6 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Track rollers

SG20

SG20 is a track rollers designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 6 × 24 × 11 mm. The publishing works are in Fujian province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
6 mm
Outside D
24 mm
Width B
11 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-08

Which SG20 do you need—and does it fit your axle and rail?

Runstar publishes two SG20 detail pages: one labelled Rubber seal and one labelled shields. Both have a 6 mm bore and an 8 mm guide-size field. Start by identifying those two interfaces and the closure on your old roller; they answer different replacement questions.

Choose between the two actual SG20 listings.

The rubber-seal listing [1] and shield listing [2] both publish d/D/B = 6/24/11 mm, B1 = 12.75 mm and mass = 25 g. The range table repeats SG20 without explaining the difference; the individual pages resolve that repetition. A bare SG20 line on a quote still leaves the closure open.

For an existing assembly, compare photographs of both roller faces with the selected drawing and state which closure you are replacing. For a new assembly, tell Runstar what reaches the roller—dry dust, moisture or a cleaning process—and request the closure and lubricant specification that the quote actually covers. Neither listing gives a washdown rating or establishes stainless material.

The useful purchase decision is a particular Runstar construction with an order code. The words Rubber seal and shields on these pages do not establish that another supplier uses the same suffix or closure geometry.

Use three separate checks for a roller that will not fit.

QuestionSG20 evidenceCheck on your assembly
Will it go on the axle?d = 6 mmIdentify axle diameter, fit and inner-ring support from the mounting drawing.
Will the spacer stack support the correct ring?B = 11 mm; B1 = 12.75 mmLocate the actual inner-ring end faces and clearance to the outer ring and closure.
Will it run on the existing rail?Guide-size field = 8 mmCompare the offered contact profile with the rail drawing, not just its nominal diameter.

B1 exceeds B by 1.75 mm, calculated from the published numbers. That does not establish equal protrusion on both faces: the page gives no complete axial profile drawing. Do not divide that difference in half to design two spacers without the drawing.

If an 8 mm pin is being proposed through the bearing, stop that dimensional comparison: Runstar's 8 mm entry is the guide field, while the mounting bore is 6 mm. If the old mounting pin is 6 mm but the rail is different, resolve the rail contact separately. These are drawing checks, not a diagnosis of a worn assembly.

The 8 mm guide field still leaves the contact drawing unresolved.

The two SG20 pages specify a suitable guide size but give no complete contact-contour tolerance or permissible load. If the rail is being retained, the missing item is a drawing that identifies where this offered groove contacts that rail—not another copy of the 6/24/11 dimensions.

Send Runstar the rail cross-section and the axle/roller positions. Ask it to identify the mating profile and the allowable loading of this combination. An answer containing only a bearing load rating would leave the rail contact unresolved. Schaeffler’s track-roller background [3] explains why bearing and track loading are separate checks; none of its INA numerical limits is a Runstar SG20 limit.

If the supplier cannot establish that combination, retain SG20 as an unqualified candidate. This catalogue does not approve a payload or a life. For a proposed move to SG25, first compare the changed bore, body, inner-ring width and guide field; it is not a like-for-like replacement.

What each manufacturer published.

ManufacturerReference mass (kg)Source recorded
Runstar
SG20
0.0252026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 29 mm
Mean diameter dm(D + d) / 215 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish SG20.

Runstar

Zhangzhou, Fujian, China

Miniature ball and thrust bearings

Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.

Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs

223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Runstar about SG20

Applications the publishing works state.

ApplicationStated by
Fishing tackleRunstar
Medical equipmentRunstar
Precision instrumentsRunstar
Small motorsRunstar

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Request a quote for SG20.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Runstar · SG20 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Runstar · SG20 rubber-seal detail ↗

    d/D/B/B1, guide-size field, mass and Rubber seal label. No permissible load, rail profile, material or environmental approval established.

  2. Runstar · SG20 shield detail ↗

    Separate shields listing with the same envelope and guide field; exact order suffix to be confirmed.

  3. Schaeffler · Track Roller Guidance Systems LF1 ↗

    Printed pages 12–13: bearing/track loading and unsupported outer-ring considerations. Background only; INA numerical limits not copied to Runstar.

Guide checked 2026-10-08. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.