BearingIndex
THE BEARINGINDEX DIRECTORY

ZKLF1255.2RS — 12 × 55 × 25 mm

BOUNDARY DIMENSIONSUNIT / mm

FYB’s ZKLF1255.2RS row gives 12/55/25 mm plus mounting reference J 42 mm, 3×120° positions and three M6 fixing screws. Its series section also identifies shoulder and locating interfaces. A plain d/D/B envelope cannot describe this mounting arrangement.

Thrust

ZKLF1255.2RS

ZKLF1255.2RS is a thrust designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 12 × 55 × 25 mm. The publishing works are in Jiangsu province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
12 mm
Outside D
55 mm
Width B
25 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Keep the 2RS speed entry and the three-M6 mounting pattern with the complete designation.

FYB lists ZKLF1255.2RS and ZKLF1255.2Z at the same 12×55×25 mm size, mass and load figures. Their grease-speed entries differ: 3800 versus 7600 min⁻¹. The same publication excludes sealed products from its oil-speed increase note and provides mounting dimensions beyond the three-number size. Those details need separate checks when selecting a screw-support bearing or considering a suffix change.

The matching dimensions do not give 2RS the 2Z speed entry.

FYB’s exact paired rows [1] share the listed size, mass and basic load numbers. The speed column is explicitly labelled grease and min⁻¹; keep the suffix on each row when reading it.

FYB designationBore / outside / widthMass and source-labelled ratingsGrease limiting speed
ZKLF1255.2RS12 / 55 / 25 mm0.37 kg; Cr 17 / Cor 24.7 kN.3800 min⁻¹
ZKLF1255.2Z12 / 55 / 25 mm0.37 kg; Cr 17 / Cor 24.7 kN.7600 min⁻¹

For a requirement of 4000 rpm, the 2RS row is already below the requested speed. That is a reason to obtain another assessed configuration or FYB’s part-specific engineering response, rather than approve the 2RS from the 2Z row’s 7600 figure. The two rows’ identical catalogue loads do not resolve the closure, friction or lubrication differences.

Read the oil note’s exception. FYB’s Chinese note describes a 30% speed increase with oil lubrication but excludes sealed configurations. Do not turn 3800×1.3 into a 4940 rpm permission for the offered 2RS. The English note refers to sealed roller followers even though this page is headed thrust angular-contact ball bearings; have FYB confirm the applicable instruction for the selected bearing.

The publication also marks load, speed and mass as selection references. Neither 3800 nor 7600 is a measured result for your installed support. Ask for the offered seal and grease, permissible duty conditions and application assessment. A change to 2Z requires its own contamination/sealing and lubrication review, rather than being a speed-only substitution.

Retain the source’s Cr/Cor labels for the 17/24.7 kN entries and obtain their applicable load definitions from FYB. This table does not provide a tested installed stiffness, preload setting or positioning accuracy; those results cannot be derived from the larger static number or from the series name.

J 42 and three M6 fixings belong on the mounting drawing.

The FYB series section and end view [2] show locating faces, diameters and fixing positions. The exact 1255.2RS row supplies their numerical entries. Match those interfaces to the housing/support before treating the 55 mm outside diameter as sufficient mounting evidence.

Exact row [1]Published entryKeep the source qualifier
J / spacing t42 mm / 3×120°Use the labelled mounting reference and positions on the controlled drawing.
Fixing screwsM6, quantity 3The table supplies size/count, rather than tightening torque or a complete fastening specification.
d2 / b / l6.5 / 3 / 17 mml is marked minimum; identify the section’s corresponding features and tolerances before release.
d1 / D125 / 33.5 mmBoth columns are marked minimum; retain their source symbols rather than treating them as bore d12 or outside D55.
B25 mm; −0.25 annotation under B.Obtain the complete controlled tolerance definition; do not copy nominal 25 as an exact measured width.

The series illustration contains several visible features, but the table specifies three M6 fixing screws for this row. Do not turn the illustration into a six-screw instruction. Obtain the selected drawing’s fixing-hole identification, positions, engagement and mounting procedure for the actual support.

Include the mating shoulder/locating surfaces and shaft retention in the technical enquiry. Ask FYB to mark d1/D1, the section features and the width datum on that drawing. The low-resolution series image does not release machining tolerances, fastening torque or an assembled setting procedure.

The 2Z row repeats these listed mounting entries, which makes it a useful comparison of the source columns. It does not establish that a suffix change is approved for the complete machine. Review the mounting and retention requirements together with the separate sealing, lubrication and speed decision, and keep the resulting drawing revision with the order.

What each manufacturer published.

ManufacturerBore (mm)Outside diameter (mm)Width (mm)Reference mass (kg)Source recorded
FYB
ZKLF1255.2RS
125525
The current FYB table places a −0.25 annotation under the B header; obtain its controlled tolerance definition.
0.372026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings.

The works that publish ZKLF1255.2RS.

FYB

Zhenjiang, Jiangsu, China

Needle roller bearings and combined assemblies

FYB publishes needle-bearing, combined-support and track-roller ranges. Its ZKLF table distinguishes closure-specific speeds and mounting interfaces; obtain the exact offered configuration and controlled drawing for the shaft, housing and load path.

Published ranges: Needle-and-cage assemblies · Drawn-cup and combined needle bearings · Track rollers and cylindrical roller bearings · Thrust bearings and clutch-release units

23 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask FYB about ZKLF1255.2RS

Applications the publishing works state.

ApplicationStated by
Automotive assembliesFYB
Machine toolsFYB

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Request a quote for ZKLF1255.2RS.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. FYB · ZKLF1255.2RS source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. FYB · ZKLF exact paired rows, headers and bilingual notes ↗

    ZKLF1255.2RS/2Z: 12/55/25 mm, 0.37 kg, Cr 17/Cor 24.7 kN, grease speeds 3800/7600 min⁻¹; mounting/qualifier entries and reference-only note. Chinese oil-speed increase excludes sealed configurations; English follower wording needs selected-part clarification.

  2. FYB · ZKLF.2RS series section and end view ↗

    Series locating/fixing diagram, actually paired with exact-table values. Its low-resolution labels and multiple depicted features do not establish selected machining tolerances, screw count beyond the table or an assembly setting procedure.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.