Jingjiu
Jingjiu’s catalogue covers linear guides, ball screws, spherical/rod-end bearings and linear-motion components. Actual JGH20CA/HA rows distinguish block length and ratings despite the same assembly height; the SFU table uses kgf load ratings and the rod-end page explicitly identifies left-hand threading. The company offers defined inspection and test services, which can support a drawing-specific validation plan rather than a blanket special-environment claim.
Specify the complete axis or joint, then agree the evidence for its duty.
Zhejiang Jingjiu Bearing Industry Co., Ltd. (浙江精久轴承工业有限公司) publishes linear guides, ball screws, spherical/rod-end bearings, linear shafts and accessories. The official introduction describes guide-profile drawing, straightening, hardening, drilling and grinding within its factory. Use the actual model drawings and test-service offer to establish the candidate configuration and acceptance; general special-environment categories do not define its rating. Actual company and manufacturing scope [1]
Two “20” blocks can share height and still require different mounting space.
The actual JGH table, also read in the browser, gives the following millimetre dimensions and kN load ratings. These are catalogue values for the complete identified configuration; they do not approve replacement blocks on another manufacturer’s rail. Actual JGH dimensional/rating rows [2]
| Published block | H / W / L, mm | Block bolt spacing C | Dynamic / static rating |
|---|---|---|---|
| JGH20CA | 30 / 44 / 78 | 36 mm | 17.75 / 37.85 kN |
| JGH20HA | 30 / 44 / 93 | 50 mm | 21.2 / 48.85 kN |
The drawing’s bolt-spacing C and the rating column’s dynamic C are different quantities. Send the rail/block drawing, rail length/end distances, block quantity and arrangement, datum shoulders, bolt pattern and available envelope. Ask for the applicable accuracy, preload, interchangeability/matching policy, straightness/parallelism and installation requirements.
The miniature JSG table includes some models with missing load fields and differing availability marks. Missing values are not zero or a basis for scaling a smaller size’s rating. Request the controlled candidate sheet and current availability; for small assemblies, confirm wiper, lubrication access and handling/retention during installation. Actual JSG miniature table [3]
Keep the full screw suffix, nut envelope and rating units.
The actual SFU table lists SFU1605-3 and SFU1605-4 with the same 16 mm diameter and 5 mm lead, but nut length L of 43 and 50 mm. It defines the circuit-count column and states its load ratings in kgf, while the guide table uses kN. Do not compare the raw numbers as the same unit or erase the suffix when asking for a substitute. Actual SFU table and unit notes [4]
Provide travel, total screw length, end machining, support-bearing arrangement, nut mounting, orientation, axial load, acceleration and duty cycle. Agree lead/positioning accuracy, backlash/preload, critical-speed/buckling assessment, lubrication, end-support components and installed torque/temperature acceptance. A diameter-and-lead designation alone does not identify the complete drive axis.
The table advises consultation for small diameters and identifies left-helix availability through specific marks. Request written feasibility and a controlled drawing for the actual hand, size and end geometry. A catalogue tick or historic product page is not a current delivery commitment.
Confirm the thread, sliding pair and oscillation duty together.
The self-lubricating SA detail gives SA20C an M20 × 1.5 thread and explicitly says left-hand products add L, with SAL20C as its example. It describes carbon-steel forged rod-end bodies and distinguishes composite and PTFE-fabric sliding pairs associated with the C/ET constructions. Confirm the exact liner, seals and thread on the proposed drawing rather than assigning one material to the whole range. Actual SA/ET detail and left-hand note [5]
Send thread diameter/pitch/hand, engagement and locking method, pin/bore fits, mounting envelope, oscillation angle, load directions, shock, frequency and temperature/environment. Ask for the applicable motion-dependent life and liner-wear criteria, allowable misalignment and corrosion protection. “Self-lubricating” does not remove the need to confirm contamination, storage and maintenance conditions.
For an existing linkage, provide both joint ends and the full assembly drawing. Matching a thread or pin diameter is not enough to approve axial load, tilt or replacement length; retain the controlled suffix and handedness.
Use the actual service menu to define a paid or included validation programme.
The technical-service page offers selection/design and technical agreements, standard-based inspection reports, hardness/effective-layer and metallographic work, salt-spray, static-load, no-load running, oscillating-life and guide-block dust testing. It also offers PPAP/FMEA and specifies paid dynamic life testing for bearings/guides/screws. Ask which deliverables are included in the quote and which require a separate programme. Actual technical-service menu [6]
Application validation
Define loads/moments, speed/acceleration, travel, duty and lubrication. Agree fixture, sample quantity, duration, failure/wear criteria and who approves the complete machine or joint.
Environment and materials
Define dust particle/exposure, corrosion medium, temperature cycle and any vacuum/cleanliness requirement. Request the relevant material/coating, seal/wiper and process evidence for the exact candidate.
The page gives an environmental-test range of −80°C to 150°C. This is an advertised test-service range, not a temperature rating for every guide, lubricant, seal or liner. Similarly, a test rig’s load capacity is not a component’s allowable load. Request a report that identifies the drawing revision, specimen, conditions and result. Actual test limits and service wording [6]
- Freeze the technical agreement. Identify model, materials, accuracy/preload and acceptance standards.
- Approve representative samples. Link geometry, material and functional/environment evidence to the controlled production route.
- Control repeat manufacture. Agree lot inspection, traceability and notification before process, lubricant, liner, seal or site changes.
Verify the standard edition and the site responsible for the order.
The national standards platform independently lists Jingjiu among the drafting organisations for GB/T 19673.1-2025, covering sleeve-type linear-ball-bearing accessories, with an implementation date of 1 February 2026. It also lists the company on JB/T 5306-2025 for ball-stud rod ends. These support specific drafting participation, not certification of every product in the catalogue. Confirm which standard and edition actually apply to the quoted component. Actual national-standard record [7] Actual rod-end industry-standard record [8]
Zhejiang’s public portal marks one company declaration for GB/T 32322.1-2015 as withdrawn by the enterprise. That is the status of this particular declaration, not proof that the national standard itself is withdrawn or that a product failed testing. Obtain the current contract declaration and candidate conformity report rather than relying on that record. Actual enterprise-declaration status [9]
The dedicated contact gives 135 Qibaiyang Street, Nanmingshan, Liandu, Lishui; catalogue footers still give 16 Baixian Road. Confirm the manufacturing/inspection and sample-receiving sites. Technical/key-account contact: 0578-2269588; sales manager: 0578-2262838 / 2692333; email: [email protected]. The dedicated page’s supplier-procurement numbers are for selling inputs to Jingjiu, not the buyer’s product enquiry route. Actual contact and departmental routing [10] Actual catalogue footer address [2]
For ISO9001, GJB9001C or a specialised customer requirement, request the applicable current certificate, legal entity/site scope and approval evidence. The company introduction’s broad capability claims do not establish current candidate approval or unrestricted interchangeability. Scope of company system/application claims [1]
Prepare a Jingjiu linear-axis or linkage enquiry
Tick what you have ready. Copy the full checklist with its current status for your procurement notes.
Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.
Documented models.
42 model recordsEvidence, with boundaries.
Our review approach →Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.
- Official actual introduction, also read in browserJingjiu · company and production scope ↗
Range and guide-profile process claims; current certificates/customer approval require originals.
- Official actual dimensional/rating table; CA/HA rows read in browserJingjiu · JGH guide/block table ↗
H/W/L, bolt spacing and kN ratings; matching/accuracy and current availability require confirmation.
- Official actual miniature tableJingjiu · JSG miniature guide table ↗
Published dimensions and some missing rating fields; no inferred ratings or unit correction.
- Official actual table and notationJingjiu · SFU ball-screw table ↗
1605 suffix/length difference, lead and kgf load-unit notes; full drive configuration needs approval.
- Official actual table and construction notesJingjiu · self-lubricating SA/ET rod ends ↗
Thread/left-hand marking and sliding-pair alternatives; candidate drawing resolves geometry/material choice.
- Official actual test/service menuJingjiu · technical services and testing ↗
PPAP/FMEA, material/dust/environment and paid life tests; rig ranges are not universal product ratings.
- Primary actual current national-standard recordSAMR · GB/T 19673.1-2025 record ↗
Specific drafting organisation, scope and implementation date; not product certification.
- Primary actual industry-standard recordSAMR · JB/T 5306-2025 record ↗
Specific ball-stud rod-end drafting participation; candidate compliance still requires evidence.
- Primary actual enterprise-declaration statusZhejiang standards portal · company declaration ↗
One enterprise declaration marked withdrawn; not the national standard’s status or a failed-product result.
- Official actual contact and department listJingjiu · current dedicated contact page ↗
Qibaiyang135, technical/sales route and procurement distinction; production/receiving assignment requires confirmation.
Report a source correction → · Return to inquiry checklist ↑
Jingjiu published product scope reviewed
The manufacturer website describes spherical plain bearings and linear motion.
Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.
Company-level record; not a model test report · 2026-09-24 04:20:33
Source documentation retained for editorial review.