BearingIndex
THE BEARINGINDEX DIRECTORY

GE10E — 10 × 19 × 9 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 9 mmD = 19 mmd = 10 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical plain

GE10E

GE10E is a spherical plain designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 10 × 19 × 9 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
10 mm
Outside D
19 mm
Width B
9 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

GE10E is listed as 9 mm wide. Does that also define the outer-ring seat?

Jingjiu’s row gives B = 9 mm and C = 6 mm. Its series drawing uses B across the inner ring and C across the outer ring. Preserve both dimensions in the joint drawing; the three-number envelope alone does not describe the locating arrangement or the joint’s permitted motion.

B and C belong to different rings in this manufacturer’s drawing.

Jingjiu’s actual GE10E row [1] gives d = 10 mm, D = 19 mm, B = 9 mm and C = 6 mm. The embedded series drawing [2] identifies B across the inner ring and C across the outer ring. A drawing that uses 9 mm for both leaves the outer-ring geometry incorrectly represented.

The nominal width difference is 3 mm in total. That arithmetic does not define a 1.5 mm spacer on each side or an approved locating stack. Show which faces locate each ring and check the joint’s surrounding parts against the selected controlled drawing.

The row also publishes dk = 16 mm, d1 = 13 mm and minimum edge radii r1s/r2s of 0.3 mm. Keep these symbols with the manufacturer’s diagram; the edge-radius entries are not a complete mating-shoulder specification.

In this table, C = 6 is a dimension in millimetres. The dynamic/static load columns are separate and show 8.1/40 kN. Do not confuse a dimensional symbol with a load rating or treat the 40 kN entry as a tested complete-joint working load.

The approximate 12° drawing entry does not define the duty cycle.

Jingjiu’s column is marked α° ≈ and gives 12 for GE10E. Its diagram places α at the inclined-axis geometry. This provides an approximate catalogue tilt entry; it is not a statement of your mechanism’s swing frequency, total travel per cycle or running life.

Show the required axis misalignment and nearby-part clearances on the actual assembly drawing. Separately state the working swing about the joint, its half-angle convention and the number of cycles per minute. Do not use the approximate 12° field to fill all of those inputs.

The series drawing’s enlarged detail names GE…ES-2RS. The GE10E row has a dash in the second model column, rather than a listed GE10E-2RS designation. Ask for any required sealed construction explicitly; a sealed series illustration does not prove that this row supplies it.

This is a maintenance-classified plain bearing, so the operating question changes.

Jingjiu places the examined range under “spherical plain bearings requiring maintenance”. The row does not define GE10E’s selected sliding-contact materials, lubricant, relubrication interval or permissible working speed. Obtain those from Jingjiu for the actual load and movement pattern.

THK’s spherical-plain-bearing selection explanation [3] describes a wear-based life assessment influenced by sliding-contact materials, load magnitude/direction, lubrication and sliding speed. It treats rocking motion and its frequency as duty inputs. This is technical background; its numerical coefficients and operating limits are not assigned to Jingjiu GE10E.

Technical references may also use different symbols: THK’s cited selection text defines B as outer-ring width, while Jingjiu’s drawing uses C for that width. Do not insert Jingjiu’s B = 9 into another maker’s formula by matching the letter alone.

Send the load cases, swing half-angle/frequency, temperature and maintenance access to Jingjiu. Request the offered construction, lubrication instructions and the wear/clearance criterion used for the intended duty. A ball-bearing fatigue-life calculation copied onto the 8.1 kN entry does not supply that assessment.

The catalogue’s inventory column contains a check mark and lists approximate mass 0.011 kg. It gives no dated quantity or delivery commitment for your order. Confirm availability and the complete supplied item in the quotation.

What each manufacturer published.

ManufacturerDynamic load rating (kN)Static load rating (kN)Reference mass (kg)Source recorded
Jingjiu
GE10E
8.1400.0112026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 24.5 mm
Mean diameter dm(D + d) / 214.5 mm
C / C₀ load ratiodynamic ÷ static load ratingJingjiu 0.2

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish GE10E.

Jingjiu

Lishui, Zhejiang, China

Spherical plain bearings and linear motion

Jingjiu publishes linear-motion components, ball screws and spherical/rod-end bearings. Its spherical-bearing catalogue separates designs requiring maintenance from maintenance-free designs and labels the GE15ES/GE15ES-2RS row’s load ratings in kN. Choose the complete joint and mounting drawing, then confirm its sealing and lubrication requirements for the actual motion.

Published ranges: Lubricated and self-lubricating spherical plain bearings · Rod-end and angular-contact plain bearings · Linear ball bearings and guideways · Ball screws and supporting components

42 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Jingjiu about GE10E

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Application · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Other designations with the same 10x19x9 mm envelope.

DesignationBearing familyWorks
GE10ESSpherical plain1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
GE100ES100 × 150 × 70Spherical plain2
GE100ES-2RS100 × 150 × 70Spherical plain2
GE10ES10 × 19 × 9Spherical plain1

Each envelope shown is that designation’s own published size.

Request a quote for GE10E.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Jingjiu · GE10E source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Jingjiu · exact GE10E maintenance-range table ↗

    Actual full headers and GE10E row read: mm/kN units, ring widths, geometry, approximate angle, ratings and mass. Second model dash and inventory check mark retained without availability or seal inference.

  2. Jingjiu · embedded series dimensional drawing ↗

    Manufacturer diagram actually viewed: B inner-ring/C outer-ring widths and alpha tilted-axis indication. GE…ES-2RS enlarged detail is not proof of a sealed GE10E item.

  3. THK · Selecting a Spherical Plain Bearing ↗

    Official selection text read: wear-based service-life concept and movement/lubrication inputs; outer-width symbol convention. Background only, no THK coefficients, safety factor or operating limit transferred.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.