Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical plain
GE100ES-2RS
GE100ES-2RS is a spherical plain designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 100 × 150 × 70 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.
Does a GE100ES-2RS quotation promise a maintenance-free joint?
The suffix alone does not make that promise. Jingjiu explicitly places GE100ES-2RS in its “requiring maintenance” catalogue range. Obtain the selected manufacturer’s actual construction and maintenance instructions before ordering an inaccessible or supposedly maintenance-free assembly.
Use the manufacturer’s classification, then request its actual service requirement.
Jingjiu’s current catalogue page [1] pairs GE100ES with GE100ES-2RS and classifies the range as spherical plain bearings requiring maintenance. That does not support buying its listed item as maintenance-free merely because the quoted designation ends in 2RS.
Ask Jingjiu to identify the offered sliding-contact materials and closure construction, initial lubricant and maintenance instructions for the actual duty. The examined row gives no relubrication interval, temperature range or approved continuous operating life.
If the supplier requires a lubrication route, show how that route remains accessible in the assembled joint and ask for the relevant bearing drawing. Do not assume that an outer-ring opening, an inner-ring opening or a housing passage can be inferred from a series picture or from the suffix alone.
For a Wuling offer, obtain Wuling’s own maintenance classification and instructions. Its examined sheet names the paired variant but does not provide the same written maintenance classification; Jingjiu’s classification is not silently transferred to that offer.
Matching geometry does not merge two manufacturers’ documentation.
Both examined publications give d = 100 mm, D = 150 mm, inner-ring width B = 70 mm and outer-ring width C = 55 mm. Their series drawings distinguish the ring widths. Keep the actual locating arrangement on the selected drawing; the 15 mm total width difference does not specify symmetric spacers.
Examined field
Jingjiu [1]
Wuling [2]
Dynamic / static entries
607 / 3030 kN; unit explicitly stated
610 / 3050; load unit not stated in the examined header
Catalogue mass
Approximately 4.45 kg
4.3 kg
Angle entry
α ≈ 7°
7°
Confirm Wuling’s load units and rating basis before making a numerical capacity comparison. Do not combine its larger displayed numbers with Jingjiu’s kN label. Neither manufacturer’s catalogue mass is a measured packed-shipping weight for your order.
The angle belongs to the inclined-ring geometry shown by the series diagrams. It is not the mechanism’s complete swing-duty definition. Specify axis misalignment and the working swing angle/frequency separately.
A large static rating cannot replace the actual joint assessment.
Jingjiu’s 3030 kN static entry is a bearing catalogue rating. The source does not supply the allowable load of your shaft, housing or complete mechanism. Ask the selected manufacturer to assess the actual radial/axial load cases, load direction, motion, lubrication and mounting arrangement.
If maintenance-free operation is an essential requirement, state it explicitly and request a construction and written duty assessment meeting that requirement. Do not erase the requirement by copying an unqualified “sealed” description into the order.
The useful quotation package identifies the exact manufacturer and item, provides the controlled mounting and lubrication drawing, explains the applicable ratings and states the maintenance requirement. Jingjiu’s inventory check mark supplies no dated quantity or delivery commitment; obtain those separately for the actual order.
A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.
Calculated from the published values.
Figure
How it is obtained
Result
Radial section height
(D − d) / 2
25 mm
Mean diameter dm
(D + d) / 2
125 mm
C / C₀ load ratio
dynamic ÷ static load rating
Jingjiu 0.2
Arithmetic on the figures above — not a bearing life calculation for your load case.
Jingjiu publishes linear-motion components, ball screws and spherical/rod-end bearings. Its spherical-bearing catalogue separates designs requiring maintenance from maintenance-free designs and labels the GE15ES/GE15ES-2RS row’s load ratings in kN. Choose the complete joint and mounting drawing, then confirm its sealing and lubrication requirements for the actual motion.
Published ranges: Lubricated and self-lubricating spherical plain bearings · Rod-end and angular-contact plain bearings · Linear ball bearings and guideways · Ball screws and supporting components
42 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Wuling publishes linear-motion parts and articulating joints. Its radial spherical-plain catalogue separates ring widths and lists seal variants by exact row; specify the joint’s required movement and the complete offered construction.
Published ranges: Linear ball bearings · Stud-type needle track rollers · Rod-end and spherical plain bearings · Linear guides and sliding units
52 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08
Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.
Fields absent from the recorded dataset.
Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.
Ask the manufacturer for these when you enquire.
Other designations with the same 100x150x70 mm envelope.
Current class heading and exact paired row freshly read: explicit maintenance classification, mm/kN/kg headers, 100/150/70/C55 dimensions, approximate angle and rating entries. Embedded series drawings viewed; no duty or interval inferred.
Original image actually viewed with exact paired row, mm/kg headings and angle. Load unit is not stated in the examined header; maintenance instructions absent. Different manufacturer, not a shared operating approval.
Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.
We use cookies and analytics to operate this website and measure visits. Form contents and private workspace pages are excluded from analytics. Privacy & cookies