BearingIndex
THE BEARINGINDEX DIRECTORY

GE10ES — 10 × 19 × 9 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 9 mmD = 19 mmd = 10 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Spherical plain

GE10ES

GE10ES is a spherical plain designation documented on BearingIndex from 1 manufacturer publication. The published boundary dimensions are 10 × 19 × 9 mm. The publishing works are in Zhejiang province, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
10 mm
Outside D
19 mm
Width B
9 mm

Compare the 1 publication

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Wuling’s GE10ES catalogue describes a fitting crack. What should receiving inspection check?

The manufacturer explicitly labels this range “单开缝” and “with fitting crack”. That is evidence of an intended series construction, not permission to accept every crack on a delivered part. Identify the specified feature on the selected drawing and compare the actual sample before deciding.

A catalogue construction and an observed defect are different evidence.

Wuling’s original sheet [1] names the normal series as spherical plain radial bearings with a fitting crack. It includes series sections and a product photograph. Keep that manufacturer description with the receiving specification instead of rejecting an intended feature merely because the word “crack” appears.

The series sheet does not identify the position and permissible condition of every feature on your delivered GE10ES batch. Request the controlled drawing or written feature definition for the supplied item, then compare the actual part with it. Record unexpected damage, burrs or marks for supplier review rather than assuming the catalogue description explains them.

This page has no sample photograph or inspection report from your order. It does not diagnose a delivered crack as harmless or approve the part for service. A useful receiving decision joins the specified construction to actual lot evidence.

Do not remove S merely because another maker lists GE10E at the same size.

Wuling’s exact GE10ES row gives d = 10 mm, D = 19 mm, B = 9 mm and C = 6 mm. Its drawing distinguishes the two ring widths. The row also gives d1 minimum = 13 mm, an angle entry of 12° and mass 0.011 kg.

Jingjiu’s examined row [2] instead names its 10/19/9 item GE10E, also with C = 6 mm. These are actual published designations from two manufacturers. Matching nominal dimensions does not establish that the letter difference is a typo or that the constructions are identical.

Retain the quoted manufacturer and full designation. If replacing a different maker’s GE10E, request the offered GE10ES drawing and confirmation of the actual sliding-contact construction, lubrication provisions and mounting requirements. This guide does not assign a universal lubrication-hole meaning to S from a different company’s code convention.

The source leaves load units and a sealed GE10ES offer unconfirmed.

Wuling’s load-rating columns display dynamic 8.15 and static 40.5, but the examined header does not state their units. Ask for the unit and rating basis before using either in a selection calculation. Jingjiu explicitly labels its separate GE10E ratings 8.1/40 kN; that label does not fill Wuling’s missing unit or prove a capacity increase.

The sheet lists paired ES / ES-2RS designations starting at GE15ES. It does not list a GE10ES-2RS item beside GE10ES. The series heading and sealed section illustration do not establish availability of that smaller sealed variant. If sealing is required, ask Wuling for an explicitly defined offer with its own drawing.

The next useful quotation identifies GE10ES, its actual construction and intended fitting-crack feature, confirms the load units and resolves any required seal and maintenance provision. The catalogue alone cannot settle batch condition or operating life.

What each manufacturer published.

ManufacturerSource recorded
Wuling
GE10ES
2026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 24.5 mm
Mean diameter dm(D + d) / 214.5 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish GE10ES.

Wuling

Lishui, Zhejiang, China

Linear and spherical plain bearing systems

Wuling publishes linear-motion parts and articulating joints. Its radial spherical-plain catalogue separates ring widths and lists seal variants by exact row; specify the joint’s required movement and the complete offered construction.

Published ranges: Linear ball bearings · Stud-type needle track rollers · Rod-end and spherical plain bearings · Linear guides and sliding units

52 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Wuling about GE10ES

Applications the publishing works state.

ApplicationStated by
Machine toolsWuling
Medical machineryWuling
Printing machineryWuling
Textile machineryWuling

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter · Reference mass.

Ask the manufacturer for these when you enquire.

Other designations with the same 10x19x9 mm envelope.

DesignationBearing familyWorks
GE10ESpherical plain1

Same envelope, but sealing, internal design, clearance and load capability differ — not interchangeable by default.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
GE100ES100 × 150 × 70Spherical plain2
GE100ES-2RS100 × 150 × 70Spherical plain2
GE10E10 × 19 × 9Spherical plain1

Each envelope shown is that designation’s own published size.

Request a quote for GE10ES.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Wuling · GE10ES source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Wuling · original normal-series GE / GE-2RS sheet ↗

    Original 800×1022 image actually viewed: single fitting-crack series heading, sections and exact GE10ES row. mm/kg headings explicit, load units absent; no GE10ES-2RS paired designation. Series material is not an actual batch inspection.

  2. Jingjiu · exact GE10E row for designation comparison ↗

    Actual 10/19/9 GE10E row read with C6 and explicit kN load headings. Different manufacturer; no interchange or code-normalization approval.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.