BearingIndex
THE BEARINGINDEX DIRECTORY

SFH

Shanghai Hengan markets SFH miniature ball bearings and states that it was established in 2001, with a Wuxi factory and Shanghai measurement, technical and inspection functions. Its product pages list alternative ring, ball, cage and closure materials and nonstandard drawing/design work. Specify the complete construction and installed torque/noise/clearance requirements; ABEC labels, ceramic balls and application headings do not establish speed, whole-bearing nonmagnetism or medical/aerospace approval.

MINIATURE BALL BEARINGS · SPECIFY CONSTRUCTION AND INSTALLED BEHAVIOUR

Match the miniature bearing’s materials, clearance and starting behaviour.

Shanghai Hengan Miniature Bearing Co., Ltd. (上海恒安微型轴承有限公司) describes a company established in 2001, with a Wuxi factory and Shanghai measurement, technical and quality-inspection functions. Its SFH range includes metric/inch deep-groove, flanged, thin-section, double-row angular-contact, thrust and nonstandard bearings. Qualify the complete supplied construction and the intended assembly rather than selecting from precision or special-material keywords alone. Actual company introduction and site functions [1]

Prepare a sourcing inquiry
01

Specify rings, balls, cage and closure as one controlled design.

The actual metric, thin-section and nonstandard detail pages list alternative ring materials including GCr15, 9Cr18, 300-series stainless steel, cobalt/titanium alloys and M50; ball options include steel/stainless steel and zirconia, silicon nitride or silicon carbide ceramics. They also list crown/wave/full-ball arrangements, metal/nylon/polyimide cage options, metal shields and several rubber/PTFE closure options. These are advertised choices, not proof that every combination is available for every size. Actual metric product description [2] Actual thin-section description [3] Actual nonstandard offer [4]

RequirementDefine before quotationRequest for the candidate
Low torque or quiet motorStarting/running torque, load and speed, temperature, fit/clearance and test conditions.Specified grease/fill, cage and closure, torque/noise test method and limits; “EMQ” or precision grade alone is insufficient.
Corrosion or chemical exposureActual fluid/cleaner, exposure cycle, temperature and required cleanliness.Exact alloy and heat treatment for rings/balls, cage and seal compatibility, lubricant and relevant test evidence.
Nonmagnetic requirementWhole-component magnetic requirement and measurement/acceptance conditions.Materials for every part plus the agreed magnetic-property test. Ceramic balls do not establish that metal rings or the complete bearing meet the requirement.
Thin section or special envelopeSupport/fits, installation envelope, loading/deflection and accuracy needs.Controlled drawing and installed clearance/precision requirements; the thin-section family label is not a load or rigidity rating.

The manufacturer lists applications including medical devices and small aircraft, but no candidate-specific medical, airworthiness or customer qualification was established here. State the applicable approval/testing requirement explicitly. Actual application wording and its scope [1]

02

Use the old technical charts to ask precise questions, not to release a part.

The technical page consists largely of original charts. Those images were loaded and visually read in the browser. Its clearance chart gives C2/C0/C3/C4/C5 groupings by nominal bore and also lists special MC2–MC5 ranges, with both MC3 and MC4 labelled “Standard” despite different ranges. Confirm the actual specified clearance, units, measurement method and installed target. Shaft/housing fit and temperature must be considered in the assembly; a group name is not the final mounted clearance. Actual viewed technical charts [5]

The old precision chart references GB/T 307.1-2005 and includes ABEC/ISO comparison columns through ABEC-9, while the company introduction describes an ABEC-1 to ABEC-7 range. The image’s English and Chinese grade-count wording also differs. Do not infer current ABEC-9 supply or universal equivalence from that old chart. Agree the current standard/edition and dimensional/rotational acceptance features on the candidate drawing. Actual chart and wording [5] Actual advertised range [1]

Standard-envelope part

Send full designation/suffix and a controlled envelope drawing. Confirm ring widths, flange/taper/protruding-inner-ring features if present, fits, retention, seal/shield and cage, with clearance and grease specified.

Nonstandard design

The actual page offers manufacture to drawings or design to customer requirements. Agree who owns the design, feasibility review, drawing revision, prototype acceptance and changes. For a double-row angular-contact or thrust arrangement, define load directions and locating/setting requirements explicitly.

The details link an older hengan.pdf, while the sample-download page links a newer SFH-2024.pdf. The newer link was attempted, but its download did not complete; its model contents were not read. Request the current issued catalogue and controlled drawing instead of treating an old web chart as the latest order specification. Actual download page and newer link [6] Older product-page download route [2]

03

Grease temperature, bearing torque and assembled noise need separate checks.

The actual technical image discusses oil/grease lubrication, a general filled-grease temperature statement of −30 to 100 °C and special lubricant selection. A separate image lists several historical lubricant codes, brands and temperature ranges. These are manufacturer reference statements, not a current entire-bearing temperature envelope or proof of current lubricant availability. Agree the exact supplied grease/oil, fill, material/seal compatibility and combined speed/load/temperature duty. Do not use a lubricant table maximum as the complete assembly rating. Actually viewed lubrication text and table [5]

  1. Define the measurable behaviour. State starting/running torque, rotational/dimensional requirements, load/speed, noise/vibration, temperature and contamination or cleanliness criteria where needed.
  2. Inspect representative samples. Obtain lot-linked geometry/clearance results, material identity and the agreed torque/noise tests with measurement conditions and uncertainty/calibration evidence.
  3. Validate the actual host assembly. Record installation, fits/retention and operating cycle. Check the buyer’s defined torque, heat, noise/vibration or wear criteria; bearing-only tests cannot isolate all motor/device assembly effects.
  4. Release repeat supply. Agree traceability, lubricant/material/site/process-change approval, packaging cleanliness and storage, reinspection and complaint measurements. Confirm sample cost, quantity and committed delivery.

The actual detection-centre page states that it performs production/finished-bearing precision measurement and accepts external measurement work. It does not establish accredited scope, uncertainty or a guaranteed service turnaround. Ask which named measurement and report can be provided for your part. Actual detection-centre scope [7]

04

Match the order’s factory and inspection route to current certificate scope.

The introduction describes a Wuxi factory and Shanghai headquarters functions; the contact page publishes Unit 208H, second floor, Building 10, 1188 Lianhang Road, Pujiang Town, Minhang, Shanghai. Confirm which site manufactures, assembles, inspects and releases the quoted part, and where samples should be received. A commercial contact address is not automatically the audited manufacturing site. Actual production/Shanghai function description [1] Actual dedicated contact [8]

The introduction’s certificate images were actually loaded and visually read inside the company page after a standalone image navigation initially returned no usable image. The displayed ISO 9001:2015 certificate covers miniature-bearing design/production, showing 4 November 2021 to 3 November 2024. The displayed IATF 16949:2016 certificate shows 12 October 2022 to 11 October 2025 and refers to an appendix for scope. Both show a Kangqiao East Road address, differing from the current contact page. These historical images do not establish current renewal or coverage of a Wuxi site. Obtain current originals, appendices and issuer-status evidence for the actual legal entity and manufacturing/support sites. Actual company page and viewed certificate images [1] Current published commercial address [8]

The published enquiry route is +86 21 68183666, contacts Wu/Zhang/Zhu/Zou and [email protected], [email protected], [email protected]. Confirm the engineering and quality owner for the selected construction before shipping samples. No enquiry was sent. Employee, historical output and “1,600 varieties” statements were not verified as current available capacity or stock. Actual contacts [8] Scope of manufacturer capacity statements [1]

YOUR NEXT STEP

Prepare an SFH miniature-bearing construction and behaviour brief

Tick what you have ready. Copy the full checklist with its current status for your procurement notes.

Checks stay in this page and reset on reload. Nothing is sent to the manufacturer. The inquiry link opens a separate form.

Materials to prepare
Continue to sourcing inquiry →

Documented models.

51 model records
Model / bearing familyManufacturerBore dOutside DWidth B / T / LDetails

Evidence, with boundaries.

Our review approach →

Facts above are attributed to their source. Buying and qualification steps are BearingIndex editorial suggestions. Sources checked ; this is not the sources’ publication date or an independent factory audit.

  1. Actual official text; embedded ISO/IATF images loaded and visually read in browserSFH Hengan · introduction and original certificate images ↗

    History, advertised range and Shanghai/Wuxi functions; historical certificate dates/addresses not current renewal or site coverage.

  2. Actual official product descriptionSFH Hengan · metric deep-groove detail ↗

    Advertised material/cage/closure alternatives and older catalogue link; not every combination/model approval.

  3. Actual official product descriptionSFH Hengan · thin-section detail ↗

    Family and construction options; no invented rigidity/load ratings.

  4. Actual official product descriptionSFH Hengan · nonstandard detail ↗

    Manufacture to drawings or design to requirements; ownership, acceptance and capability require agreement.

  5. Original JS1/bg1x/bg2/bg3 images loaded and actually viewed in browserSFH Hengan · original technical image charts ↗

    Historical precision/clearance/material/noise/lubrication references; not a current controlled model specification.

  6. Actual official link page; newer PDF incomplete downloadSFH Hengan · sample download ↗

    SFH-2024.pdf link actually observed; contents not reviewed and no current model values inferred.

  7. Actual official publicationSFH Hengan · detection centre ↗

    Production/product and external measurement offer; accreditation, uncertainty and turnaround not established.

  8. Actual official publicationSFH Hengan · dedicated contact ↗

    Lianhang Road commercial contact and email routes; exact sample/site responsibility not tested.

Report a source correction → · Return to inquiry checklist ↑

SFH published product scope reviewed

The manufacturer website describes miniature and thin-section ball bearings.

Scope: Official website product scope only. No independent factory audit, material-report review or model-level performance validation is implied.

Company-level record; not a model test report · 2026-09-24 04:20:33

Source documentation retained for editorial review.