BearingIndex
THE BEARINGINDEX DIRECTORY

51100 — 10 × 24 × 9 mm

BOUNDARY DIMENSIONSUNIT / mm
B = 9 mmD = 24 mmd = 10 mm
Boundary dimensions · schematic, not a product photograph or manufacturing drawing.
Thrust

51100

51100 is a thrust designation documented on BearingIndex from 2 manufacturer publications. The published boundary dimensions are 10 × 24 × 9 mm. The publishing works are in Zhejiang, Fujian provinces, China. Every value below comes from that manufacturer’s own published material, with the date it was recorded.

Bore d
10 mm
Outside D
24 mm
Width B
9 mm

Compare the 2 publications

MODEL-SPECIFIC BUYER GUIDE · SOURCES CHECKED 2026-10-09

Which 51100 washer belongs against the shaft shoulder?

Runstar’s detailed 51100 table gives different washer bores: 10 mm for the shaft washer and 11 mm for the housing washer. A single “10×24×9” size line hides that distinction. Identify both parts and the load path on the selected drawing before assembling or ordering a replacement.

The 10 mm and 11 mm bores have different jobs.

Runstar’s actual 51100 detail [1] identifies the washer dimensions individually:

Runstar dimensionPublished valueWhat to resolve on the assembly drawing
Shaft washer bore d10 mmIdentify the washer located with the shaft and its shoulder.
Housing washer bore d111 mmIdentify the washer supported on the housing side; do not mistake this bore for the nominal shaft seat.
Housing washer outside diameter D24 mmCheck the actual housing-side support and locating arrangement.
Shaft washer outside diameter D124 mmThe same outside diameter does not make the washers identical.
Assembly thickness H9 mmResolve the complete axial stack; this is not a published thickness for each washer.

The nominal bore difference is 1 mm in diameter. It is not a tolerance, fit class or permission to exchange the two washers. Runstar does not publish the individual washer thicknesses or the shaft/housing fit limits on this page.

SKF’s thrust-ball mounting explanation [3] distinguishes the smaller-bore shaft washer from the housing washer and places the shaft washer against a shaft step or fixed shaft component. Use that principle to understand the parts, then obtain the chosen supplier’s controlled mounting drawing. SKF’s component-interchangeability statement concerns its own bearings; it does not authorize mixing a PLB washer with a Runstar cage or washer.

A reversing motor and a reversing axial load are different selection questions.

PLB lists 51100 under its single-direction thrust-ball range [2]. SKF’s design explanation describes the single-direction arrangement as locating and carrying axial load in one direction; a double-direction design has a different arrangement [3].

On the machine drawing, show which shaft component pushes against which washer and where that force reaches the housing. Check the working axial force direction during normal operation, starting, stopping and any reversal. A motor changing its rotation direction does not, by itself, establish whether the axial force changes direction.

If the required thrust changes direction, submit both load cases and the locating arrangement to the selected manufacturer. Do not assume that turning over a loose washer, or ordering two unassessed 51100 assemblies, establishes a suitable double-direction system.

SKF also describes thrust ball bearings as axial-load bearings, with no radial loading [3]. Identify the separate radial support in the actual machine. The 10 mm shaft-washer bore is not evidence that this bearing supplies radial guidance or capacity for the assembly.

Runstar publishes more than PLB’s size row; keep that information with Runstar.

Both current manufacturer rows give a 10 / 24 / 9 nominal envelope. PLB lists mass 0.019 kg; Runstar lists 19 g. Those mass entries agree after unit conversion, but they do not establish identical cages, fits or operating limits.

Runstar’s detail publishes 10 kN dynamic and 14 kN static entries, 6000 RPM for grease and 9000 RPM for oil. These are Runstar’s catalogue entries, not PLB ratings or a complete machine load/speed approval. PLB’s examined 51100 row supplies no equivalent rating or speed values.

Runstar lists bearing-steel washers and balls, with a brass or steel cage. Resolve which cage is actually quoted; an option list does not identify the delivered construction. Its temperature range and its grease/oil speed entries do not show an approved simultaneous temperature, load and speed operating point.

For a replacement, request a complete, identified assembly and a drawing that shows both washer bores, the total stack and shoulder support. Include axial force directions and lubricant in the duty request. Runstar’s blank cross-brand correspondence cells provide no interchange evidence, and its certification status labels were not checked against certificates or a supplied lot.

What each manufacturer published.

ManufacturerReference mass (kg)Source recorded
Runstar
51100
0.0192026-09-24 source ↗Request
PLB
51100
0.0192026-09-24 source ↗Request

A dash means the site’s recorded data does not provide that value; it is not proof that the manufacturer has never published it. Check the reviewed source notes for any newer findings. Dimensions every source agrees on are shown above rather than repeated per row.

Compare the recorded figures.

PropertyFindingSources
Reference massAll 2 sources publish 0.019 kg2

Where the figures differ, use the drawing from the manufacturer you buy from.

Calculated from the published values.

FigureHow it is obtainedResult
Radial section height(D − d) / 27 mm
Mean diameter dm(D + d) / 217 mm

Arithmetic on the figures above — not a bearing life calculation for your load case.

The works that publish 51100.

PLB

Ningbo, Zhejiang, China

Motor, steering and custom precision bearings

PLB connects a searchable miniature/automotive catalogue with named inspection equipment and ring/assembly process steps. Specify closure-dependent widths, keep alternator reference numbers separate from the delivered construction, and request part-linked test conditions for custom robot or rail-component work.

Published ranges: Automotive alternator and steering bearings · Motor bearings · Precision spindle-bearing applications · Nonstandard bearing designs

124 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask PLB about 51100

Runstar

Zhangzhou, Fujian, China

Miniature ball and thrust bearings

Runstar publishes miniature, flanged and thrust bearings, with separate dental and ceramic product routes. Its SF692 variants have different ring widths, and some published dimensional or mass entries require clarification. Use the complete designation and controlled drawing for the offered product; catalogue application labels do not establish medical approval or a verified ceramic composition.

Published ranges: Miniature deep groove ball bearings · Small deep groove ball bearings · Flat thrust ball bearings · Nonstandard miniature designs

223 designations documented here · 1 reviewed evidence record · source recorded 2026-10-08

Ask Runstar about 51100

Applications the publishing works state.

ApplicationStated by
Automotive systemsPLB
Electric motorsPLB
Fishing tackleRunstar
Machine-tool spindlesPLB
Medical equipmentRunstar
Precision instrumentsRunstar
Small motorsRunstar

Application areas each manufacturer states for its own range. Confirm load, speed, temperature and lubrication for your case.

Fields absent from the recorded dataset.

Precision class · Internal clearance · Sealing · Material · Cage material · Z class · V class · Dynamic load rating · Static load rating · Limiting speed · Lubrication · Operating temperature · Precision standard · Ring material · Rolling element material · Limiting speed — grease · Limiting speed — oil · Noise / vibration test method · Manufacturer series · Manufacturer suffix · Ball count · Ball diameter.

Ask the manufacturer for these when you enquire.

Neighbouring designations documented here.

DesignationEnvelope d × D × B (mm)Bearing familyWorks
5110112 × 26 × 9Thrust2
5110215 × 28 × 9Thrust2
5110317 × 30 × 9Thrust2
5110420 × 35 × 10Thrust2
51105—Thrust2
5110630 × 47 × 11Thrust1
5110735 × 52 × 12Thrust1
5110840 × 60 × 13Thrust1
5110945 × 65 × 14Thrust1
5111050 × 70 × 14Thrust1
5111155 × 78 × 16Thrust1
5111260 × 85 × 17Thrust1
5111365 × 90 × 18Thrust1
5111470 × 95 × 18Thrust1
5111575 × 100 × 19Thrust1
5111680 × 105 × 19Thrust1
5111785 × 110 × 19Thrust1
5111890 × 120 × 22Thrust1

Each envelope shown is that designation’s own published size.

Request a quote for 51100.

Tick the works you want above, then send one enquiry — each manufacturer answers you separately and cannot see the others.

Open your enquiry How sourcing works here →

Figures on this page are each manufacturer’s own published material, recorded on the dates shown. How we check sources →

PREPARE THE NEXT CONVERSATION

Turn your requirements into an enquiry.

Keep the catalogue reference and your requirements separate. Blank fields remain questions for the manufacturer.

Your entries stay in this page, are not uploaded, and reset on reload. Building or copying this brief does not send an enquiry.

Review your selected products and open the enquiry form →

Open the evidence behind the comparison.

Catalogue figures belong to the stated manufacturer and document. A recording date is not a new inspection, current quotation or confirmed stock.

  1. Runstar · 51100 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

  2. PLB · 51100 source ↗

    Directory record dated 2026-09-24. Confirm the current complete designation and controlled drawing with this manufacturer.

Sources used for the individual buyer guide

  1. Runstar · actual 51100 detailed product page ↗

    Fresh detail text read: washer d/d1/D/D1, H, material/cage alternatives, ratings and RPM headers. Options and status labels do not prove the delivered construction or certification; product image did not load.

  2. PLB · actual 51100 row and single-direction catalogue ↗

    Fresh specific row and series page read: d/D/B in mm and kg; 10/24/9 and 0.019. Series diagram actually viewed uses H for overall stack, but no numeric individual-washer dimensions or ratings were published in the examined row.

  3. SKF · thrust-ball design and mounting explanation ↗

    PDF pages 468–472, printed 466–470; design and mounting text read, pages 469 and 472 rendered and viewed. Technical explanation only; no SKF rating, component interchange or fit approval transferred to Runstar/PLB.

Guide checked 2026-10-09. Manufacturer statements, technical background and BearingIndex purchasing suggestions are distinguished in the text. This is not application approval or firsthand product testing.